Average Log Length and Payment Reduction Clause Samples

Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine ▇▇▇▇▇▇▇▇ mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
View SourceView Similar (57)
Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine ▇▇▇▇▇▇▇▇ mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
View SourceView Similar (32)
Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) Where:
View SourceView Similar (14)
Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine ▇▇▇▇▇▇▇▇ mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code. Purchaser must provide a plan in writing, acceptable to the State, to acquire third party ▇▇▇▇▇▇▇▇ mbf scaling information in order to be eligible for a payment reduction for a tonnage sort according to clauses P-036.2 or P-037.2. Logs delivered and accepted by the Purchaser prior to the State’s acceptance of Purchaser’s written payment reduction plan are not eligible for payment reduction. Failure of Purchaser to provide sample scale data in a timely, accurate and legible basis will void an approved sample scale plan. An approved payment reduction plan can be voided at the sole discretion of the State. For the purpose of tonnage sort payment reduction requests, preferred log lengths for tonnage sawlog sorts shall include the following plus any additional lengths identified in clause G-024.2: Species Type Preferred Lengths Conifer Sorts 16’, 20’, 24’, 26’, 32’, 40’ Hardwood Sorts 18’, 20’, 26’, 28’, 30’, 36’, 38’, 40’
View Source
Average Log Length and Payment Reduction. If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine ▇▇▇▇▇▇▇▇ mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
View Source

Related to Average Log Length and Payment Reduction

  • Subsequent Recalculation In the event the Internal Revenue Service adjusts the computation of the Company under Section 5.2 herein so that the Executive did not receive the greatest net benefit, the Company shall reimburse the Executive for the full amount necessary to make the Executive whole, plus a market rate of interest, as determined by the Committee, within 30 days after such adjustment.

  • Calculation and Payment Interest on LIBOR Loans and all other Obligations and the amount of any fees set forth in Subsection 1.4 shall be calculated on the basis of a three hundred sixty (360) day year for the actual number of days elapsed. Interest on the Base Rate Loans shall be calculated on the basis of a three hundred sixty-five or -six (365-6) day year for the actual number of days elapsed. The date of funding or conversion to a Base Rate Loan and the first day of an Interest Period with respect to a LIBOR Loan shall be included in the calculation of interest. The date of payment of any Loan and the last day of an Interest Period with respect to a LIBOR Loan shall be excluded from the calculation of interest; provided, if a Loan is repaid on the same day that it is made, one (1) day’s interest shall be charged. Interest accruing on the Base Rate Loan is payable in arrears on each of the following dates or events: (i) the last day of each calendar quarter; (ii) the prepayment of such Loan (or portion thereof); and (iii) the applicable Maturity Date or the Revolving Loan Expiration Date, as the case may be, whether by acceleration or otherwise. Interest accruing on each LIBOR Loan is payable in arrears on each of the following dates or events: (i) the last day of each applicable Interest Period; (ii) if the Interest Period is longer than three (3) months, on each three-month anniversary of the commencement date of such Interest Period; (iii) the prepayment of such Loan (or portion thereof); and (iv) the applicable Maturity Date or the Revolving Loan Expiration Date, as the case may be, whether by acceleration or otherwise.

  • Application of Commitment Reductions; Payment of Fees The Administrative Agent will promptly notify the Appropriate Lenders of any termination or reduction of unused portions of the Letter of Credit Sublimit or the Swing Line Sublimit or the unused Commitments of any Class under this Section 2.06. Upon any reduction of unused Commitments of any Class, the Commitment of each Lender of such Class shall be reduced by such Lender’s Pro Rata Share of the amount by which such Commitments are reduced (other than the termination of the Commitment of any Lender as provided in Section 3.07). All commitment fees accrued until the effective date of any termination of the Aggregate Commitments shall be paid on the effective date of such termination.

  • Measurement and Payment Temporary traffic control work, including, but not limited to installation and removal of portable signs, cones, drums, skinny drums, flaggers, AFAD’s, changeable message boards, truck mounted attenuators, flashing arrow boards, and pilot vehicles will be paid at the contract lump sum price for

  • Mandatory Repayments and Commitment Reductions (a) If on any date the aggregate amount of all Letter of Credit Outstandings and Bank Guaranty Outstandings exceeds the Total Credit-Linked Commitment as then in effect, the U.S. Borrower or the Bermuda Borrower (as determined by the U.S. Borrower) (subject to clause (x) of the proviso to this clause (a)) agrees to pay to the Administrative Agent at the Payment Office on such date an amount of cash and/or Cash Equivalents in Dollars equal to such excess, such cash or Cash Equivalents to be held as security for all Obligations of the respective Borrower (including, without limitation, in the case of the U.S. Borrower pursuant to the Credit Agreement Party Guaranty) to the Issuing Lenders, Bank Guaranty Issuers and Lenders relating to Letters of Credit and Bank Guaranties (and reimbursement and other Obligations relating thereto) hereunder in a cash collateral account to be established by, and under the sole dominion and control of, the Administrative Agent; provided that (x) the aggregate amount of cash and/or Cash Equivalents paid by the Bermuda Borrower to the Administrative Agent under this clause (a) shall not at any time exceed the sum of the Letter of Credit Outstandings (with respect to Bermuda Borrower Letters of Credit) and the Bank Guaranty Outstandings (with respect to Bermuda Borrower Bank Guaranties) at such time and (y) any such cash and/or Cash Equivalents shall first be applied to repay any amounts owing to the respective Issuing Lender and Bank Guaranty Issuer as described in Section 2C.03 hereof. (i) In addition to any other mandatory repayments or commitment reductions pursuant to this Section 4.02, on each date set forth below, the U.S. Borrower shall be required to repay that principal amount of Tranche B Term Loans, to the extent then outstanding, as is set forth opposite such date (each such repayment, as the same may be reduced as provided in Sections 4.01 and 4.02(g), a “Tranche B Term Loan Scheduled Repayment”):