DCS Technical Requirements. 11.6.1 DCS shall provide completed end-to-end cross connection of the channels designated by Advent. 11.6.2 Where technically available in BellSouth's DCS system and supported by BellSouth's network management software, DCS shall provide multiplexing, format conversion, signaling conversion, or other functions. 11.6.3 The end-to-end cross connection assignment shall be input to the underlying device used to provide DCS from an operator at a terminal or via an intermediate system. The cross connection assignment shall remain in effect whether or not the circuit is in use. 11.6.4 BellSouth shall continue to administer and maintain DCS, including updates to the control software to current available releases. 11.6.5 BellSouth shall provide various types of Digital Cross-Connect Systems including: 11.6.5.1 DS0 cross-connects (typically termed DCS 1/0); 11.6.5.2 DS1/VT1.5 (Virtual Tributaries at the 1.5Mbps rate) cross-connects (typically termed DCS 3/1); 11.6.5.3 DS3 cross-connects (typically termed DCS 3/3); 11.6.5.4 STS-1 cross-connects; and 11.6.5.5 Other technically feasible cross-connects designated by Advent. 11.6.6 DCS shall continuously monitor protected circuit packs and redundant common equipment. 11.6.7 Where technically available in BellSouth’s DCS System, DCS shall automatically switch to a protection circuit pack on detection of a failure or degradation of normal operation. 11.6.8 The underlying equipment used to provide DCS shall be equipped with a redundant power supply or a battery back-up. 11.6.9 BellSouth shall make available to Advent spare facilities and equipment necessary for provisioning repairs, as it does for itself and for its own customers. 11.6.10 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform optical to electrical conversion where the underlying equipment used to provide DCS contains optical interfaces or terminations (e.g., Optical Carrier level 3, i.e., OC-3, interfaces on a DCS 3/1). 11.6.11 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall have SONET ring terminal functionality where the underlying equipment used to provide DCS acts as a terminal on a SONET ring. 11.6.12 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall provide multipoint bridging of multiple channels to other DCSs. Advent may designate multipoint bridging to be one-way broadcast from a single master to multiple tributaries, or two-way broadcast between a single master and multiple tributaries. 11.6.13 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall multiplex lower speed channels onto a higher speed interface and demultiplex higher speed channels onto lower speed interfaces as designated by Advent. 11.6.14 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform signaling conversion and data conditioning as designated by Advent.
Appears in 1 contract
Sources: Interconnection Agreement
DCS Technical Requirements. 11.6.1 8.6.1 DCS shall provide completed end-to-end cross connection of the channels designated by AdventComputer Business Sciences.
11.6.2 8.6.2 Where technically available in BellSouth's ’s DCS system and supported by BellSouth's ’s network management software, DCS shall provide multiplexing, format conversion, signaling conversion, or other functions.
11.6.3 8.6.3 The end-to-end cross connection assignment shall be input to the underlying device used to provide DCS from an operator at a terminal or via an intermediate system. The cross connection assignment shall remain in effect whether or not the circuit is in use.
11.6.4 8.6.4 BellSouth shall continue to administer and maintain DCS, including updates to the control software to current available releases.
11.6.5 8.6.5 BellSouth shall provide various types of Digital Cross-Connect Systems including:
11.6.5.1 8.6.5.1 DS0 cross-connects (typically termed DCS 1/0);
11.6.5.2 8.6.5.2 DS1/VT1.5 (Virtual Tributaries at the 1.5Mbps rate) cross-connects (typically termed DCS 3/1);
11.6.5.3 8.6.5.3 DS3 cross-connects (typically termed DCS 3/3);
11.6.5.4 8.6.5.4 STS-1 cross-connects; and
11.6.5.5 8.6.5.5 Other technically feasible cross-connects designated by AdventComputer Business Sciences.
11.6.6 8.6.6 DCS shall continuously monitor protected circuit packs and redundant common equipment.
11.6.7 8.6.7 Where technically available in BellSouth’s DCS System, DCS shall automatically switch to a protection circuit pack on detection of a failure or degradation of normal operation.
11.6.8 8.6.8 The underlying equipment used to provide DCS shall be equipped with a redundant power supply or a battery back-up.
11.6.9 8.6.9 BellSouth shall make available to Advent Computer Business Sciences spare facilities and equipment necessary for provisioning repairs, as it does for itself and for its own customers.
11.6.10 8.6.10 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform optical to electrical conversion where the underlying equipment used to provide DCS contains optical interfaces or terminations (e.g., Optical Carrier level 3, i.e., OC-3, interfaces on a DCS 3/1).
11.6.11 8.6.11 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall have SONET ring terminal functionality where the underlying equipment used to provide DCS acts as a terminal on a SONET ring.
11.6.12 8.6.12 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall provide multipoint bridging of multiple channels to other DCSs. Advent Computer Business Sciences may designate multipoint bridging to be one-way broadcast from a single master to multiple tributaries, or two-way broadcast between a single master and multiple tributaries.
11.6.13 8.6.13 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall multiplex lower speed channels onto a higher speed interface and demultiplex higher speed channels onto lower speed interfaces as designated by AdventComputer Business Sciences.
11.6.14 8.6.14 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform signaling conversion and data conditioning as designated by AdventComputer Business Sciences.
Appears in 1 contract
Sources: Interconnection Agreement
DCS Technical Requirements. 11.6.1 12.6.1 DCS shall provide completed end-to-end cross connection of the channels designated by AdventSupra Telecommunications and Information Systems, Inc. .
11.6.2 12.6.2 Where technically available in BellSouth's DCS system and supported by BellSouth's network management software, DCS shall provide multiplexing, format conversion, signaling conversion, or other functions.
11.6.3 12.6.3 The end-to-end cross connection assignment shall be input to the underlying device used to provide DCS from an operator at a terminal or via an intermediate system. The cross connection assignment shall remain in effect whether or not the circuit is in use.
11.6.4 12.6.4 BellSouth shall continue to administer and maintain DCS, including updates to the control software to current available releases.
11.6.5 12.6.5 BellSouth shall provide various types of Digital Cross-Connect Systems including:
11.6.5.1 12.6.5.1 DS0 cross-connects (typically termed DCS 1/0);
11.6.5.2 12.6.5.2 DS1/VT1.5 (Virtual Tributaries at the 1.5Mbps rate) cross-connects (typically termed DCS 3/1);
11.6.5.3 12.6.5.3 DS3 cross-connects (typically termed DCS 3/3);
11.6.5.4 12.6.5.4 STS-1 cross-connects; and
11.6.5.5 12.6.5.5 Other technically feasible cross-connects designated by AdventSupra Telecommunications and Information Systems, Inc. .
11.6.6 12.6.6 DCS shall continuously monitor protected circuit packs and redundant common equipment.
11.6.7 12.6.7 Where technically available in BellSouth’s DCS System, DCS shall automatically switch to a protection circuit pack on detection of a failure or degradation of normal operation.
11.6.8 12.6.8 The underlying equipment used to provide DCS shall be equipped with a redundant power supply or a battery back-up.
11.6.9 12.6.9 BellSouth shall make available to Advent Supra Telecommunications and Information Systems, Inc. spare facilities and equipment necessary for provisioning repairs, as it does for itself and for its own customers.
11.6.10 12.6.10 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform optical to electrical conversion where the underlying equipment used to provide DCS contains optical interfaces or terminations (e.g., Optical Carrier level 3, i.e., OC-3, interfaces on a DCS 3/1).
11.6.11 12.6.11 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall have SONET ring terminal functionality where the underlying equipment used to provide DCS acts as a terminal on a SONET ring.
11.6.12 12.6.12 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall provide multipoint bridging of multiple channels to other DCSs. Advent Supra Telecommunications and Information Systems, Inc. may designate multipoint bridging to be one-way broadcast from a single master to multiple tributaries, or two-way broadcast between a single master and multiple tributaries.
11.6.13 12.6.13 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall multiplex lower speed channels onto a higher speed interface and demultiplex higher speed channels onto lower speed interfaces as designated by AdventSupra Telecommunications and Information Systems, Inc. .
11.6.14 12.6.14 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform signaling conversion and data conditioning as designated by AdventSupra Telecommunications and Information Systems, Inc. .
Appears in 1 contract
Sources: Interconnection Agreement
DCS Technical Requirements. 11.6.1 DCS shall provide completed end-to-end cross connection of the channels designated by AdventSupra Telecommunications and Information Systems, Inc. .
11.6.2 Where technically available in BellSouth's ’s DCS system and supported by BellSouth's ’s network management software, DCS shall provide multiplexing, format conversion, signaling conversion, or other functions.
11.6.3 The end-to-end cross connection assignment shall be input to the underlying device used to provide DCS from an operator at a terminal or via an intermediate system. The cross connection assignment shall remain in effect whether or not the circuit is in use.
11.6.4 BellSouth shall continue to administer and maintain DCS, including updates to the control software to current available releases.
11.6.5 BellSouth shall provide various types of Digital Cross-Connect Systems including:
11.6.5.1 DS0 cross-connects (typically termed DCS 1/0);
11.6.5.2 DS1/VT1.5 (Virtual Tributaries at the 1.5Mbps rate) cross-connects (typically termed DCS 3/1);
11.6.5.3 DS3 cross-connects (typically termed DCS 3/3);
11.6.5.4 STS-1 cross-connects; and
11.6.5.5 Other technically feasible cross-connects designated by AdventSupra Telecommunications and Information Systems, Inc. .
11.6.6 DCS shall continuously monitor protected circuit packs and redundant common equipment.
11.6.7 Where technically available in BellSouth’s DCS System, DCS shall automatically switch to a protection circuit pack on detection of a failure or degradation of normal operation.
11.6.8 The underlying equipment used to provide DCS shall be equipped with a redundant power supply or a battery back-up.
11.6.9 BellSouth shall make available to Advent Supra Telecommunications and Information Systems, Inc. spare facilities and equipment necessary for provisioning repairs, as it does for itself and for its own customers.
11.6.10 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform optical to electrical conversion where the underlying equipment used to provide DCS contains optical interfaces or terminations (e.g., Optical Carrier level 3, i.e., OC-3, interfaces on a DCS 3/1).
11.6.11 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall have SONET ring terminal functionality where the underlying equipment used to provide DCS acts as a terminal on a SONET ring.
11.6.12 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall provide multipoint bridging of multiple channels to other DCSs. Advent Supra Telecommunications and Information Systems, Inc. may designate multipoint bridging to be one-way broadcast from a single master to multiple tributaries, or two-way broadcast between a single master and multiple tributaries.
11.6.13 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall multiplex lower speed channels onto a higher speed interface and demultiplex higher speed channels onto lower speed interfaces as designated by AdventSupra Telecommunications and Information Systems, Inc. .
11.6.14 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform signaling conversion and data conditioning as designated by AdventSupra Telecommunications and Information Systems, Inc. .
Appears in 1 contract
Sources: Telecommunications
DCS Technical Requirements. 11.6.1 8.6.1 DCS shall provide completed end-to-end cross connection of the channels designated by AdventEastland of Orlando.
11.6.2 8.6.2 Where technically available in BellSouth's DCS system and supported by BellSouth's network management software, DCS shall provide multiplexing, format conversion, signaling conversion, or other functions.
11.6.3 8.6.3 The end-to-end cross connection assignment shall be input to the underlying device used to provide DCS from an operator at a terminal or via an intermediate system. The cross connection assignment shall remain in effect whether or not the circuit is in use.
11.6.4 8.6.4 BellSouth shall continue to administer and maintain DCS, including updates to the control software to current available releases.
11.6.5 8.6.5 BellSouth shall provide various types of Digital Cross-Connect Systems including:
11.6.5.1 8.6.5.1 DS0 cross-connects (typically termed DCS 1/0);
11.6.5.2 8.6.5.2 DS1/VT1.5 (Virtual Tributaries at the 1.5Mbps rate) cross-connects (typically termed DCS 3/1);
11.6.5.3 8.6.5.3 DS3 cross-connects (typically termed DCS 3/3);
11.6.5.4 8.6.5.4 STS-1 cross-connects; and
11.6.5.5 8.6.5.5 Other technically feasible cross-connects designated by AdventEastland of Orlando.
11.6.6 8.6.6 DCS shall continuously monitor protected circuit packs and redundant common equipment.
11.6.7 8.6.7 Where technically available in BellSouth’s DCS System, DCS shall automatically switch to a protection circuit pack on detection of a failure or degradation of normal operation.
11.6.8 8.6.8 The underlying equipment used to provide DCS shall be equipped with a redundant power supply or a battery back-up.
11.6.9 8.6.9 BellSouth shall make available to Advent Eastland of Orlando spare facilities and equipment necessary for provisioning repairs, as it does for itself and for its own customers.
11.6.10 8.6.10 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform optical to electrical conversion where the underlying equipment used to provide DCS contains optical interfaces or terminations (e.g., Optical Carrier level 3, i.e., OC-3, interfaces on a DCS 3/1).
11.6.11 8.6.11 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall have SONET ring terminal functionality where the underlying equipment used to provide DCS acts as a terminal on a SONET ring.
11.6.12 8.6.12 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall provide multipoint bridging of multiple channels to other DCSs. Advent Eastland of Orlando may designate multipoint bridging to be one-way broadcast from a single master to multiple tributaries, or two-way broadcast between a single master and multiple tributaries.
11.6.13 8.6.13 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall multiplex lower speed channels onto a higher speed interface and demultiplex higher speed channels onto lower speed interfaces as designated by AdventEastland of Orlando.
11.6.14 8.6.14 Where technically available in BellSouth’s DCS System and supported by BellSouth’s network management software, DCS shall perform signaling conversion and data conditioning as designated by AdventEastland of Orlando.
Appears in 1 contract
Sources: Interconnection Agreement