Do Not Duplicate Sample Clauses

The "Do Not Duplicate" clause prohibits the reproduction or copying of certain materials, documents, or information covered by the agreement. In practice, this means that parties are not allowed to make additional copies of proprietary content, such as manuals, software, or confidential documents, without explicit permission. This clause serves to protect intellectual property and sensitive information, ensuring that valuable or confidential materials are not distributed beyond their intended scope and reducing the risk of unauthorized disclosure or misuse.
POPULAR SAMPLE Copied 1 times
Do Not Duplicate. Residents shall not violate this provision or possess University Housing keys other than the one assigned to them by the community desk.
View SourceView Similar (9)
Do Not Duplicate. Subject to the terms of this Agreement, Recipient and its Representatives may duplicate documents which do not bear the aforementioned legend, provided that such duplication is reasonably required in furtherance of the Transaction.
View Source
Do Not Duplicate. Note: In cold conditions brush or roller application may be difficult due to increase in product viscosity at low temperatures and to ease of application we will raise the temperature of the Base component to a minimum of 10oC prior to aid mixing and application. This can be achieved by keeping the product in a warm vehicle or site hut until required, or by immersing the sealed Base component in warm water prior to mixing. To maintain the specified film thickness at welds edges, round boltholes and other sharp protuberances, a stripe coat shall be applied to these areas prior to carrying out the overall application. Over-coating times are dependent on the overall room temperature and the standard time allowances are highlighted within the 11T-B system specification. The stripe coat shall be applied by brush. During application all crevices and deeply pitted surfaces shall be completely penetrated and coated particularly edges, bolt heads, weld runs, etc. During application the applicator will carry out regular checks of wet thickness with a wet film thickness gauge to ensure the specified thickness is applied.
View Source
Do Not Duplicate. Key Points –
View Source
Do Not Duplicate. COVAC possess an unparalleled wealth of experience in connection with the refurbishment of these type of structures and as a Preferred Channel Partner of 3M™ can offer Single Source 3M Scotchkote™ 165PW (formerly known as COPON Hycote 165 PW) can be applied by brush or roller and for these methods of application the product is supplied in pre-measured composite units. The Base component shall first be stirred and whilst continuing stirring, the Activator component shall be added and stirring continued until a homogeneous mix is achieved. To ensure complete mixing the product shall then be transferred to a clean container with the original container being scraped out and further mixing being carried out. A mechanical mixer will assist in ensuring correct and thorough mixing. The mixed 3M Scotchkote™ 165PW shall then be applied by brush or roller to give a uniform even thickness of a nominal 500 Microns. Two coats will be required to achieve a nominal specified thickness of 1000 Microns (1mm). To maintain the specified film thickness at joints welds, edges, around bolt heads, struts and other sharp protuberances, a stripe coat shall be applied to these areas prior to carrying out the overall application. The stripe coat shall be applied by brush whilst the overall application will be applied by brush / roller.
View Source

Related to Do Not Duplicate

  • Non-duplication In the event that the Executive shall perform services for the Bank or any other direct or indirect subsidiary or affiliate of the Company or the Bank, any compensation or benefits provided to the Executive by such other employer shall be applied to offset the obligations of the Company hereunder, it being intended that this Agreement set forth the aggregate compensation and benefits payable to the Executive for all services to the Company, the Bank and all of their respective direct or indirect subsidiaries and affiliates.

  • Non-Duplication of Payment or Benefits For purposes of clarity, in the event of a Qualifying Pre-CIC Termination, any severance payments and benefits to be provided to the Executive under Section 3(b) will be reduced by any amounts that already were provided to the Executive under Section 3(a). Notwithstanding any provision of this Agreement to the contrary, if the Executive is entitled to any cash severance, continued health coverage benefits, or vesting acceleration of any equity awards (other than under this Agreement) by operation of applicable law or under a plan, policy, contract, or arrangement sponsored by or to which any member of the Company Group is a party (“Other Benefits”), then the corresponding severance payments and benefits under this Agreement will be reduced by the amount of Other Benefits paid or provided to the Executive.

  • Non-Duplication of Benefits Executive is not eligible to receive benefits under this Agreement more than one time.

  • Third Party Administrators for Defined Contribution Plans 2.1 The Fund may decide to make available to certain of its customers, a qualified plan program (the “Program”) pursuant to which the customers (“Employers”) may adopt certain plans of deferred compensation (“Plan or Plans”) for the benefit of the individual Plan participant (the “Plan Participant”), such Plan(s) being qualified under Section 401(a) of the Code and administered by TPAs which may be plan administrators as defined in the Employee Retirement Income Security Act of 1974, as amended. 2.2 In accordance with the procedures established in Schedule 2.1 entitled “Third Party Administrator Procedures,” as may be amended by the Transfer Agent and the Fund from time to time (“Schedule 2.1”), the Transfer Agent shall: (a) Treat Shareholder accounts established by the Plans in the name of the Trustees, Plans or TPAs, as the case may be, as omnibus accounts; (b) Maintain omnibus accounts on its records in the name of the TPA or its designee as the Trustee for the benefit of the Plan; and (c) Perform all Services under Section 1 as transfer agent of the Funds and not as a record-keeper for the Plans. 2.3 Transactions identified under Sections 1 and 2 of this Agreement shall be deemed exception services (“Exception Services”) when such transactions: (a) Require the Transfer Agent to use methods and procedures other than those usually employed by the Transfer Agent to perform transfer agency and recordkeeping services; (b) Involve the provision of information to the Transfer Agent after the commencement of the nightly processing cycle of the TA2000 System; or (c) Require more manual intervention by the Transfer Agent, either in the entry of data or in the modification or amendment of reports generated by the TA2000 System, than is normally required.

  • No Duplicative Payment The Company shall not be liable under this Agreement to make any payment of amounts otherwise indemnifiable hereunder if and to the extent that Indemnitee has otherwise actually received such payment under any insurance policy, contract, agreement or otherwise.