DRAWN UP AND SIGNED Clause Samples

The "Drawn Up and Signed" clause establishes that a contract or agreement becomes valid and enforceable only once it has been formally written out and signed by the relevant parties. In practice, this means that any negotiations, drafts, or verbal agreements are not legally binding until the final document is executed with signatures. This clause ensures that all parties are clear on the terms and that there is a definitive, mutual acknowledgment of the agreement, thereby preventing disputes over informal or incomplete arrangements.
POPULAR SAMPLE Copied 1 times
DRAWN UP AND SIGNED. Place and date: ….………………………………… ….………………………………… (name of Host and signature)
View SourceView Similar (2)
DRAWN UP AND SIGNED. Place and date: ….………………………………… This contract has been created automatically. By creating the booking code sent by the Host to the tenant, the Host/employer has agreed to this contract. ….………………………………… (name Host) Place and date: ….………………………………… ….………………………………… (name tenant)
View Source
DRAWN UP AND SIGNED. Place and date: Place and date: ………………………………… ………………………………… ………………………………… ………………………………… (name Host) (name Employer)
View Source
DRAWN UP AND SIGNED. Place and date
View Source

Related to DRAWN UP AND SIGNED

  • Conditions Precedent to Each Loan and Letter of Credit The obligation of each Lender on any date (including the Closing Date) to make any Loan and of each L/C Issuer on any date (including the Closing Date) to Issue any Letter of Credit is subject to the satisfaction of each of the following conditions precedent:

  • Insurance and Fingerprint Requirements Information Insurance If applicable and your staff will be on TIPS member premises for delivery, training or installation etc. and/or with an automobile, you must carry automobile insurance as required by law. You may be asked to provide proof of insurance. Fingerprint It is possible that a vendor may be subject to Chapter 22 of the Texas Education Code. The Texas Education Code, Chapter 22, Section 22.0834. Statutory language may be found at: ▇▇▇▇://▇▇▇.▇▇▇▇▇▇▇▇.▇▇▇▇▇.▇▇▇▇▇.▇▇.▇▇/ If the vendor has staff that meet both of these criterion: (1) will have continuing duties related to the contracted services; and (2) has or will have direct contact with students Then you have ”covered” employees for purposes of completing the attached form. TIPS recommends all vendors consult their legal counsel for guidance in compliance with this law. If you have questions on how to comply, see below. If you have questions on compliance with this code section, contact the Texas Department of Public Safety Non-Criminal Justice Unit, Access and Dissemination Bureau, FAST-FACT at ▇▇▇▇@▇▇▇▇▇.▇▇▇▇▇.▇▇.▇▇ and you should send an email identifying you as a contractor to a Texas Independent School District or ESC Region 8 and TIPS. Texas DPS phone number is (▇▇▇) ▇▇▇-▇▇▇▇. See form in the next attribute to complete entitled: Texas Education Code Chapter 22 Contractor Certification for Contractor Employees

  • Investigation of Financial Condition Without in any manner reducing or otherwise mitigating the representations contained herein, Company shall have the opportunity to meet with Buyer's accountants and attorneys to discuss the financial condition of Buyer. Buyer shall make available to Company all books and records of Buyer.

  • General Conditions Applicable to Insurance All policies of insurance required by this section shall comply with the following requirements:

  • GENERAL WORKING CONDITIONS Section 18-1. Employment begins and ends at each project site. Section 18-2. The selection of craft foremen and/or general foremen and the number of foremen required shall be entirely the responsibility of the Employer, it being understood that in the selection of such foremen and/or general foremen the Employer will give primary consideration to the qualified individuals available in the local area. After giving such consideration, the Employer may select such individuals from other areas. All foremen shall take orders from the designated Employer representatives. Craft foremen shall be designated working foremen at the request of the Employer. Section 18-3. There shall be no limit on production by employees nor restrictions on the full use of tools or equipment. Employees using tools shall perform any of the work of the trade and shall work under the direction of the craft foremen. There shall be no restrictions on efficient use of manpower other than as may be required by safety regulations. Section 18-4. Employees shall be at their place of work at the starting time and shall remain at their place of work performing their assigned functions under the supervision of the Employer until quitting time. The parties reaffirm their policy of a fair day’s work for a fair day’s wage. Section 18-5. All equipment assigned to a project shall be under the control of the Employer. The Employer shall have the right to determine how many pieces of equipment an individual employee shall operate. In an emergency, foremen shall operate any equipment assigned by the Employer, and there shall be no restriction on foremen in the use of the tools of his or her craft in such emergency. The foremen shall be from the craft normally operating the equipment. In accordance with currently recognized craft jurisdiction, the Employer shall determine the assignment of employees to start, stop, and maintain small portable construction equipment. Such work may be assigned to craft employees within a reasonable distance of their primary duties or an employee may be assigned full time to start, stop and maintain the Employer’s small, portable equipment on the job site. There shall be no over ▇▇▇▇▇▇▇ of this type of equipment. The number of employees assigned to rigging and scaffolding operations shall be at the sole discretion of the Employer. The ratio of journeyperson to welders shall be determined solely by the Employer. Section 18-6. The Employer may utilize the most efficient methods or techniques of construction, tools or other labor saving devices to accomplish the work. Practices not a part of the terms and conditions of this Agreement, stand by crews and feather bedding practices will not be recognized. Section 18-7. It is recognized that specialized or unusual equipment may be installed and/ or serviced by individuals who have special training, skill, or qualifications and are not covered by this Agreement. Testing, inspection, or service performed on plant equipment under warranty may be performed by the vendor’s personnel. Section 18-8. Neither the Union nor its local unions shall coerce or in any way interfere with the Owner’s personnel, operation or facilities at the plant site. The Owner’s right to contract directly with other companies for work at the plant site shall not be limited, and the Union shall cooperate and not interfere with the Employer’s operations. Section 18-9. It is agreed that overtime is undesirable and not in the best interest of the industry or the employees; therefore, except in unusual circumstances, overtime will not be worked. Where unusual circumstances do exist, however, the Employer will have the right to assign specific employees and/or crews to perform such overtime work as is necessary to accomplish the job. Section 18-10. There will be no rest periods, organized coffee breaks or other non-working time established during working hours. Section 18-11. Individual seniority shall not be recognized or applied to employees working on projects under this Agreement. Section 18-12. The Employer shall establish such reasonable project rules as the Employer deems appropriate. These rules will be reviewed at the pre-job conference and posted at the project site by the Employer, and may be amended thereafter as necessary.