Expression of results Sample Clauses

Expression of results. Subtract the initial haze from the final haze for every measurement point, the difference representing the so-called delta haze. Calculate out of these values for the individual measurement points the average delta haze (including standard deviation) resulting from abrasion action of aqueous dirt wiped for 20,000 cycles on the sample surface by a to be reported wiper blade type.
View SourceView Similar (4)
Expression of results. Determine whether, When target (a) (see Figure 22(a)) is used, the primary and secondary images of the circle separate, i.e. whether the limit value of n is exceeded, or When target (b) (see Figure 22(b)) is used, the secondary image of the spot shifts beyond the point of tangency with the inside edge of the circle, i.e. whether the limit value of n is exceeded. Figure 22 Slot width 2 mm a) D D b) 12 mm centre spot n nt O ly Figure 23 mme Safety glazing Target Rake angle Observation distance ( X > 7 m) Suitable light source PublicCo Figure 24 Collimation telescope Observation telescope r Fo Image plane (1) Lamp bulb (2) Condenser aperture > 8.6 mm (3) Ground-glass screen aperture > condenser aperture (4) Colour filter with central hole approximately 0.3 mm in diameter, diameter > 8.6 mm (5) Polar co-ordinate plate, diameter > 8.6 mm (6) Achromatic lens, f  86 mm, aperture 10 mm (7) Achromatic lens, f  86 mm, aperture 10 mm (8) Black spot, diameter approximately 0.3 mm
View SourceView Similar (4)
Expression of results. Determine whether, When target (a) (see Figure 22(a)) is used, the primary and secondary images of the circle separate, i.e. whether the limit value of n is exceeded, or When target (b) (see Figure 22(b)) is used, the secondary image of the spot shifts beyond the point of tangency with the inside edge of the circle, i.e. whether the limit value of n is exceeded. Figure 22 Figure 23 Figure 24 (1) Lamp bulb (2) Condenser aperture > 8.6 mm (3) Ground-glass screen aperture > condenser aperture (4) Colour filter with central hole approximately 0.3 mm in diameter, diameter > 8.6 mm (5) Polar co-ordinate plate, diameter > 8.6 mm (6) Achromatic lens, f  86 mm, aperture 10 mm (7) Achromatic lens, f  86 mm, aperture 10 mm (8) Black spot, diameter approximately 0.3 mm Achromatic lens, f = 20 mm, aperture < 10 mm.
View Source
Expression of results. The safety-glass pane shall first be examined by a simple scanning technique to establish the area giving the strongest secondary image. That area shall then be examined by the collimation-telescope system at the appropriate angle of incidence. The maximum secondary-image separation shall be measured.
View Source
Expression of results. For Public Comment Only The windscreen shall first be examined by a simple scanning technique to establish the area giving the strongest secondary image. That area shall then be examined by the collimation-telescope system at the appropriate angle of incidence. The maximum secondary-image separation shall be measured.
View Source

Related to Expression of results

  • Notification of Results Within 10 days after satisfactory inspection and/or testing of Interconnection Facilities built by the Interconnection Customer (including, if applicable, inspection and/or testing after correction of defects or failures), the Interconnected Transmission Owner shall confirm in writing to the Interconnection Customer and Transmission Provider that the successfully inspected and tested facilities are acceptable for energization.

  • Publication of Results The National Aeronautics and Space Act (51 U.S.C. § 20112) requires NASA to provide for the widest practicable and appropriate dissemination of information concerning its activities and the results thereof. As such, NASA may publish unclassified and non-Proprietary Data resulting from work performed under this Agreement. The Parties will coordinate publication of results allowing a reasonable time to review and comment.

  • Ownership of Results Any interest of Contractor or its subcontractors, in the Deliverables, including any drawings, plans, specifications, blueprints, studies, reports, memoranda, computation sheets, computer files and media or other documents prepared by Contractor or its subcontractors for the purposes of this Agreement, shall become the property of and will be transmitted to City. However, unless expressly prohibited elsewhere in this Agreement, Contractor may retain and use copies for reference and as documentation of its experience and capabilities.

  • Interpretation of results 2.1.3.1. In the case of all vehicles, the time t shall not exceed 20 seconds.

  • Methods of Resolution of Disputes In the event of any dispute with respect to the construction and performance of this Agreement, the Parties shall first resolve the dispute through friendly negotiations. In the event the Parties fail to reach an agreement on the dispute within 30 days after either Party’s request to the other Parties for resolution of the dispute through negotiations, either Party may submit the relevant dispute to the China International Economic and Trade Arbitration Commission for arbitration, in accordance with its arbitration rules. The arbitration shall be conducted in Beijing. The arbitration award shall be final and binding on all Parties.