Intersections and Grade Separators Sample Clauses

Intersections and Grade Separators. All intersections and grade separators shall be as per the provision of relevant Manual. Existing intersections which are deficient shall be improved to the prescribed standards. Properly designed intersections shall be provided at the locations and of the types and features given in the tables below: (xii) At-grade intersections Major Junction: - 1 16+284 At Grade-Y Junction Junction with Slip Road and Existing Road/Ramp-5 (New NH-37/Old NH-53) 2 Near 17+430 At Grade-Y Junction Junction with End Point of Ramp -3 and Existing Road/Ramp-5 (New NH-37/Old NH-53)
View SourceView Similar (2)
Intersections and Grade Separators. All intersections shall be as per Section3 of the Manual. Existing intersections which are deficient shall be improved to the prescribed standards. There are no intersections with cross roads having bituminous surfacing. The cross roads fall into the category of VRs. The Contractor has to construct the following: Properly designed intersections shall be provided at the locations and of the types and features given in the tables below: (a) At-grade Intersections Sl. No CHAINAGE TYPE SIDE CONNECTING PLACES (b) Grade Separated Intersection With/Without Ramps S. No. Location Salient features Minimum length of viaduct to be provided Road to be carried over / under the structures
View Source
Intersections and Grade Separators. All intersections and grade separators shall be as per the provision of relevant Manual. Existing intersections which are deficient shall be improved to the prescribed standards. Properly designed intersections shall be provided at the locations and of the types and features given in the tables below: (i) At-grade intersections (ii) Major Junction: - 1 37+655 At Grade-T Junction Junction with Slip Road and Existing Road (New NH-37/Old NH-44) (iii) Minor Junction: - 1 35+175 X-Type MDR Road (Improvement below VUP with Cross Road and Connecting Road) 2 37+910 Y-LHS Village Road 3 38+▇▇▇ ▇-▇▇▇ ▇▇▇▇▇▇▇ ▇▇▇▇
View Source
Intersections and Grade Separators. All intersections and grade separators shall be as per the provision of relevant Manual. Properly designed intersections shall be provided at the locations and of the types and features given in the tables below: (i) At-grade intersections (ii) Grade separated intersection with/without ramps Sl. No. Location Salient features Minimum length of viaductto be provided Road to be carried over/under the structures
View Source
Intersections and Grade Separators. All intersections and grade separators shall be as per the provision of relevant Manual. Existing intersections which are deficient shall be improved to the prescribed standards. Properly designed intersections shall be provided at the locations and of the types and features given in the tables below: (i) At-grade intersections a. Major Junction: - b. Minor Junction: - 1 243+845 T-Junction 2 244+500 Y-Junction 3 246+150 T-Junction 4 247+150 Y-Junction 5 247+750 Y-Junction 6 250+495 X-Junction 7 250+860 T-Junction 8 253+850 Y-Junction 9 254+800 Y-Junction 10 255+100 Y-Junction 11 255+490 T-Junction 12 256+160 T-Junction 13 257+185 T-Junction (ii) Grade separated intersections with/without ramps Sl. No. Location Salient features Minimum length of viaduct to be provided Road to be carried over/under the structures
View Source
Intersections and Grade Separators. All intersections and grade separators shall be as per the provision of relevant Manual. Existing intersections which are deficient shall be improved to the prescribed standards. Properly designed intersections shall be provided at the locations of the types and features given in the tables below: (i) At-grade intersections 1 0.170 T Crossroad 5 0.605 T Paikan 7 1.455 X Crossroad 8 1.925 T Kharmohara 9 2.725 T Crossroad 11 3.340 T Barmohara 12 3.380 X Crossroad 16 5.175 T Bar Vita 18 6.050 T Crossroad 19 6.620 T Crossroad 21 8.375 X Crossroad 22 8.645 X Crossroad 24 11.250 Y Crossroad 26 11.460 X Crossroad 27 12.505 T Crossroad 32 14.875 T Crossroad 34 15.475 X Crossroad 36 18.215 T Crossroad 37 18.500 T Nibari 39 20.480 Y Crossroad 41 20.910 X Crossroad (ii) Grade separated intersection with/without ramps (1) (2) (3) (4) (5) 1) Junctions to be improved shall be as per section-3 of relevant Manual as specified in Schedule-D and MOST type design for intersection on National Highways, 1992. 2) It is clarified that if any other junction is identified during development/Construction of the project highway in addition to those mentioned above, shall also be improved with proper drainage facilities as per standards. They are deemed to be covered within the scope of work. The Number, location & type of junction shown in above table are minimum and it may increase as per actual site condition and increase in number will not attract change of Scope. 3) The contractor shall take up ‘Detailed Engineering study’ to ascertain further details of all intersections and treatment of the intersections and all shall be designed in accordance with the latest guidelines mentioned in section-3 of relevant Manual as specified in Schedule-D. The same shall not constitute a Change of Scope, save and except any variations arising out of a Change of Scope expressly undertaken in accordance with the provisions of Article 13. 4) Junction improvement under grade separators/ interchanges shall be carried out as per section-3 of relevant Manual as specified in Schedule-D and typical layout drawing attached, with proper entry/exit to cross roads and slip/service roads. 5) Traffic calming measures on Major & Minor Junction and cross Roads: The cross-road junctions as mentioned above shall be provided with Rumble strips by thermoplastic paint at the approach of junctions as per IRC: 99-2018 Guidelines for Traffic Calming Measures in Urban and Rural Areas (First Revision). 6) For cross road ...
View Source

Related to Intersections and Grade Separators

  • Geographic Area and Sector Specific Allowances, Conditions and Exceptions The following allowances and conditions shall apply where relevant. Where the Employer does work which falls under the following headings, the Employer agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.

  • COVID-19 Vaccine Passports Pursuant to Texas Health and Safety Code, Section 161.0085(c), Contractor certifies that it does not require its customers to provide any documentation certifying the customer’s COVID-19 vaccination or post-transmission recovery on entry to, to gain access to, or to receive service from the Contractor’s business. Contractor acknowledges that such a vaccine or recovery requirement would make Contractor ineligible for a state-funded contract.

  • COVID-19 Employees of Contractor and/or persons working on its behalf, including, but not limited to, subcontractors (collectively, “Contractor Personnel”), while performing services under this Agreement and prior to interacting in person with City employees, contractors, volunteers, or members of the public (collectively, “In-Person Services”) must be fully vaccinated against the novel coronavirus 2019 (“COVID-19”). “Fully vaccinated” means that 14 or more days have passed since Contractor Personnel have received the final dose of a two-dose COVID-19 vaccine series (Moderna or Pfizer-BioNTech) or a single dose of a one-dose COVID-19 vaccine (▇▇▇▇▇▇▇ & ▇▇▇▇▇▇▇/▇▇▇▇▇▇▇) and all booster doses recommended by the Centers for Disease Control and Prevention. Prior to assigning Contractor Personnel to perform In-Person Services, Contractor shall obtain proof that such Contractor Personnel have been fully vaccinated. Contractor shall retain such proof for the document retention period set forth in this Agreement. Contractor shall grant medical or religious exemptions (“Exemptions”) to Contractor Personnel as required by law. If Contractor wishes to assign Contractor Personnel with Exemptions to perform In- Person Services, Contractor shall require such Contractor Personnel to undergo weekly COVID-19 testing, with the full cost of testing to be borne by Contractor. If Contractor Personnel test positive, they shall not be assigned to perform In-Person Services or, to the extent they have already been performing In-Person Services, shall be immediately removed from those assignments. Furthermore, Contractor shall immediately notify City if Contractor Personnel performing In-Person Services (1) have tested positive for or have been diagnosed with COVID-19, (2) have been informed by a medical professional that they are likely to have COVID-19, or (3) meet the criteria for isolation under applicable government orders.

  • COVID-19 Vaccinations Contractor understands, acknowledges, and agrees that, pursuant to Article II of the General Appropriations Act, none of the General Revenue Funds appropriated to the Department of State Health Services (DSHS) may be used for the purpose of promoting or advertising COVID-19 vaccinations in the 2024-25 biennium. It is also the intent of the legislature that to the extent allowed by federal law, any federal funds allocated to DSHS shall be expended for activities other than promoting or advertising COVID-19 vaccinations. Contractor represents and warrants that it is not ineligible, nor will it be ineligible during the term of this Contract, to receive appropriated funding pursuant to Article II.

  • Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Freedom has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Freedom. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Freedom (e.g. hairpinning): 1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises. 2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated. 3. If capacity exists, provide "side-door" porting through the switch. 4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch). 2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases. 2.6.3 If no alternate facility is available, and upon request from Freedom, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Freedom will then have the option of paying the one-time SC rates to place the Loop.