Measurement principle Sample Clauses

Measurement principle. The emissions to be measured from the exhaust of the engine include the gaseous components (carbon monoxide, total hydrocarbons for diesel engines on the ESC test only; non-methane hydrocarbons for diesel and gas engines on the ETC test only; methane for gas engines on the ETC test only and oxides of nitrogen), the particulates (diesel engines only) and smoke (diesel engines on the ELR test only). Additionally, carbon dioxide is often used as a tracer gas for determining the dilution ratio of partial and full flow dilution systems. Good engineering practice recommends the general measurement of carbon dioxide as an excellent tool for the detection of measurement problems during the test run.
View SourceView Similar (5)
Measurement principle. 2.1 The opacity of the exhaust gases produced by the engine shall be measured with the engine running under full-load and at steady speed. 2.2 A sufficient number of measurements will be carried out ranging between the maximum rated speed and the minimum rated speed. The extreme points of measurement shall be situated at the limits of the interval defined above and one point of measurement will coincide with the speed at which the engine develops its maximum power and the speed at which it develops maximum torque.
View SourceView Similar (4)
Measurement principle. The emissions to be measured from the exhaust of the engine include the gaseous components (carbon monoxide, total hydrocarbons for diesel and type 3B dual-fuel engines on the ESC test only; non-methane hydrocarbons for diesel, dual-fuel and gas engines on the ETC test only; methane for gas and dual-fuel engines on the ETC test only and oxides of nitrogen), the particulates (diesel and dual-fuel engines only) and smoke (diesel and dual- fuel engines on the ELR test only). Additionally, carbon dioxide is often used as a tracer gas for determining the dilution ratio of partial and full flow dilution systems. Good engineering practice recommends the general measurement of carbon dioxide as an excellent tool for the detection of measurement problems during the test run."
View SourceView Similar (4)
Measurement principle. The engine exhaust emissions to be measured include the gaseous components (carbon monoxide, total hydrocarbons and oxides of nitrogen), and the particulates. Additionally, carbon dioxide is often used as a tracer gas for determining the dilution ratio of partial and full flow dilution systems. Good engineering practice recommends the general measurement of carbon dioxide as an excellent tool for the detection of measurement problems during the test run.
View SourceView Similar (3)
Measurement principle. The emissions to be measured from the exhaust of the engine include the gaseous components (carbon monoxide, total hydrocarbons for diesel and type 3B dual-fuel engines on the ESC test only; non-methane hydrocarbons for diesel, dual-fuel and gas engines on the ETC test only; methane for gas and dual-fuel engines on the ETC test only and oxides of nitrogen), the particulates (diesel and dual-fuel engines only) and smoke (diesel and dual- fuel engines on the ELR test only). Additionally, carbon dioxide is often used as a tracer gas for determining the dilution ratio of partial and full flow dilution systems. Good engineering practice recommends the general measurement of carbon dioxide as an excellent tool for the detection of measurement problems during the test run." Paragraph 2.1.1. amend to read: (a) For compression-ignition and dual-fuel engines: …" 4.1.2. amend to read:
View Source

Related to Measurement principle

  • Measuring EPP parameters Every 5 minutes, EPP probes will select one “IP address” of the EPP servers of the TLD being monitored and make an “EPP test”; every time they should alternate between the 3 different types of commands and between the commands inside each category. If an “EPP test” result is undefined/unanswered, the EPP service will be considered as unavailable from that probe until it is time to make a new test.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.

  • Measurement Should the State terminate this contract as herein provided, no fees other than fees due and payable at the time of termination shall thereafter be paid to the Engineer. In determining the value of the work performed by the Engineer prior to termination, the State shall be the sole judge. Compensation for work at termination will be based on a percentage of the work completed at that time. Should the State terminate this contract under paragraph (4) or (5) above, the Engineer shall not incur costs during the thirty-day notice period in excess of the amount incurred during the preceding thirty days.

  • Measurements and arithmetic conventions All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.