METERING, CHARTS Sample Clauses

The 'Metering, Charts' clause establishes the requirements and procedures for measuring and recording quantities, such as utilities or resources, used or delivered under a contract. It typically outlines how metering devices should be installed, maintained, and read, and may specify the format and frequency of charts or reports generated from these measurements. This clause ensures accurate tracking and transparent reporting of usage or delivery, helping to prevent disputes and support proper billing or compliance with contractual obligations.
METERING, CHARTS. Recording charts have been replaced by telemetering devices to reduce costs in N order to efficiently collect daily meter reading data. In the event of telemetering failure, Customer shall N take meter readings on a daily basis at a time specified by Company and shall promptly forward such readings to Company.
View SourceView Similar (11)
METERING, CHARTS. Recording charges have been replaced by telemetering devices to reduce costs in order to efficiently collect daily meter reading data. In the even of telemetering failure, Customer shall take meter readings on a daily basis at a time specified by Company and shall promptly forward such readings to Company.
View SourceView Similar (4)
METERING, CHARTS. Recording charts have been replaced by telemetering devices to reduce costs in order to efficiently collect daily meter reading data. In the event of telemetering failure, Customer shall take meter readings on a daily basis at a time specified by Company and shall promptly forward such readings to Company. Date Filed: 06-27-14 By: ▇▇▇▇▇ ▇. ▇▇▇▇▇▇ Effective Date: 11-01-14 President and CEO of Northern States Power Company, a Minnesota corporation Docket No. G002/M-14-540 Order Date: 10-17-14 Section No. Original Sheet No. 11.1 N
View Source

Related to METERING, CHARTS

  • Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.

  • Signaling protocol 4.1.3.1 SS7 Signaling is AT&T-21STATE’s preferred method for signaling. Where MF signaling is currently used, the Parties agree to use their best efforts to convert to SS7. If SS7 services are provided by AT&T-21STATE, they will be provided in accordance with the provisions of the applicable access tariffs. 4.1.3.2 Where MF signaling is currently used, the Parties agree to interconnect their networks using MF or dual tone MF (DTMF) signaling, subject to availability at the End Office Switch or Tandem Switch at which Interconnection occurs. The Parties acknowledge that the use of MF signaling may not be optimal. AT&T-21STATE will not be responsible for correcting any undesirable characteristics, service problems or performance problems that are associated with MF/SS7 inter-working or the signaling protocol required for Interconnection with CLEC employing MF signaling.

  • Calibration The comparison of a measurement system or device of unverified accuracy with a measurement system of known and greater accuracy to detect deviation of the unverified measurement system from required performance specifications (of the unverified measurement system or device) and to quantify all measured values to applicable units of the international system of units.

  • Equipment Specifications All equipment must meet the contract specifications and all federal and State safety codes and regulations in effect at the date of manufacture. All equipment must be Original Equipment Manufacturer (OEM) equipment unless otherwise stated in the contract. All products, materials, supplies, replacement parts, and equipment offered and furnished must be new, of current manufacturer production, and must have been formally announced by the manufacturer as being commercially available, unless otherwise stated in this Contract.

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at a P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.