Monitoring Installation and Testing of the System Sample Clauses

POPULAR SAMPLE Copied 1 times
Monitoring Installation and Testing of the System. Scope ofInstallation Work. Nexamp shall furnish all labor, materials and equipment to perform the Installation Work, all in accordance with Applicable Law, applicable vendors’ and manufacturers’ warranties, instructions and specifications, and applicable insurance requirements. Nexamp will cause the System to be designed, engineered, installed and constructed in accordance with the Final Drawings, Applicable Law and the terms of this Agreement. Nexamp shall perform the Installation Work in accordance with a good and workmanlike manner using only new materials and without causing material damage to any roof on the Site. Host shall havethe right to review all engineering evaluations of the impact ofthe System on the structural integrity and strength ofthe roof(s) ofthe License Area and to approve all construction plans for the System, which approval shall not be unreasonably withheld, delayed or conditioned. Host shall respond to Nexamp within ten (10) days of any request for approval hereunder. Host’s failure to respond shall be deemed to be an approval. If Host does not consent to Nexamp’s request for approval, Host shall describe in reasonable detail the basis upon whichit is denying such approval. After completion of the Installation Work, Nexamp shall not modify the System in a manner contradictoryto the Final Drawings applicable to the System without the consent of Host, which consent shall not be unreasonablywithheld, conditioned or delayed. During the Term ofthis Agreement, Nexamp shall comply with obligations imposed on an “Installer” under the Commonwealth Solar Initiative. 5.2
View Source
Monitoring Installation and Testing of the System 
View SourceView Similar (3)

Related to Monitoring Installation and Testing of the System

  • Inspection and Testing Each Constructing Entity shall cause inspection and testing of the Interconnection Facilities that it constructs in accordance with the provisions of this section. The Construction Parties acknowledge and agree that inspection and testing of facilities may be undertaken as facilities are completed and need not await completion of all of the facilities that a Constructing Entity is building.

  • Installation and Use You may install and use the Software only for the number of licenses acquired by you. In order to exercise your rights to the Software under this Agreement, you must activate your copy of the Software in the manner described during the launch sequence.

  • Installation, Maintenance, Testing and Repair Unless otherwise agreed in writing by the Parties, to the extent required by Applicable Law, Interconnection provided by a Party shall be equal in quality to that provided by such Party to itself, any subsidiary, affiliates or third party. If either Party is unable to fulfill its obligations under this Section 14.2, it shall notify the other Party of its inability to do so and will negotiate alternative intervals in good faith. The Parties agree that to the extent required by Applicable Law, the standards to be used by a Party for isolating and clearing any disconnections and/or other outages or troubles shall be at parity with standards used by such Party with respect to itself, any subsidiary, affiliate or third party.

  • Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.

  • Inspection and Tests 3.8.1 The Procuring entity or its representative shall have the right to inspect and/or to test the goods to confirm their conformity to the Contract specifications. The Procuring entity shall notify the tenderer in writing in a timely manner, of the identity of any representatives retained for these purposes. 3.8.2 The inspections and tests may be conducted in the premises of the tenderer or its subcontractor(s), at point of delivery, and/or at the Goods’ final destination If conducted on the premises of the tenderer or its subcontractor(s), all reasonable facilities and assistance, including access to drawings and production data, shall be furnished to the inspectors at no charge to the Procuring entity. 3.8.3 Should any inspected or tested goods fail to conform to the Specifications, the Procuring entity may reject the equipment, and the tenderer shall either replace the rejected equipment or make alterations necessary to make specification requirements free of costs to the Procuring entity. 3.8.4 The Procuring entity’s right to inspect, test and where necessary, reject the goods after the Goods’ arrival shall in no way be limited or waived by reason of the equipment having previously been inspected, tested and passed by the Procuring entity or its representative prior to the equipment delivery. 3.8.5 Nothing in paragraph 3.8 shall in any way release the tenderer from any warranty or other obligations under this Contract.