NEW PROCESSES Sample Clauses

NEW PROCESSES. If any process not covered by the terms of this Agreement is installed by the Company, a temporary rate will be established and the process will be put into operation. Both parties will meet within ninety (90) days after installation for the purpose of agreeing to a permanent rate. In the event the agreement on a satisfactory rate cannot be reached, the matter will be referred to the Grievance Procedure and the new rate will be effective the date of the grievance.
View SourceView Similar (8)
NEW PROCESSES. The parties will discuss in good faith the details of the introduction of new process technologies, technology roadmaps and new Process Nodes at FoundryCo (subject to, in each case, any applicable constraints to which FoundryCo may be subject pursuant to any confidentiality obligations (whether oral or in writing) to or confidentiality agreements with third parties) for use to manufacture Products, including production capacity, ramp time, dependencies and Wafer Prices. As between FoundryCo and AMD, FoundryCo will bear all expenses for introducing new process technology and new Process Nodes, as further described in Exhibit A, other than AMD-Specific Manufacturing Process Technologies.
View SourceView Similar (4)
NEW PROCESSES. The parties will discuss in good faith the details of the introduction of new process technologies into Ft. ▇▇▇▇▇▇▇, including but not limited to, necessary capital investment, production capacity and wafer prices.
View SourceView Similar (2)
NEW PROCESSES. The ▇▇▇▇▇▇▇ shall give the Union reasonable notice when the Company intends to introduce any new process or equipment. Within ten (10) days of submitting such notice the Company agrees to meet Union representatives in order to discuss the time, procedure and training necessary for the introduction of such processes or equipment. The Company agrees to provide facilities and sufficient time without loss of regular weekly wages in order that employees may become proficient in the operation of such new processes or equipment. become and remain members of the Union while covered under this Collective Agreement. They shall be entitled to all conditions of the Collective Agreement with the exception that:
View Source
NEW PROCESSES. The parties will discuss in good faith the details of the introduction of new process technologies, technology roadmaps and new Process Nodes at FoundryCo (subject to, in each case, any applicable constraints to which FoundryCo may be subject pursuant to any confidentiality obligations (whether oral or in writing) to or confidentiality agreements with third parties) for use to manufacture Products, including production capacity, ramp time, dependencies and Wafer Prices. As between FoundryCo and AMD, FoundryCo will bear all expenses for introducing new process technology and new Process Nodes, as further described in Exhibit A, other than AMD-Specific Manufacturing Process Technologies. [****] = Certain confidential information contained in this document, marked by brackets, has been omitted because it is both (i) not material and (ii) would be competitively harmful if publicly disclosed.
View Source
NEW PROCESSES. This Letter of Understanding shall take into consideration the entirety of an Employee's career. As Such, the following shall apply for the duration of the trial period:
View Source

Related to NEW PROCESSES

  • Processes Any employer, employee, trade union or employer’s association may at any point in time apply for an exemption from any of the provisions of this Collective Agreement. The applicant is required to complete and submit in writing with the relevant office of the Council, a fully and properly completed prescribed application for exemption form, accompanied by all relevant supporting documentation.

  • Product Development (a) Supplier may develop enhancements it intends to incorporate into the BioGlue Surgical Adhesive during the term of this Agreement that have potential application to the Company Product (“Enhancements”). Unless otherwise agreed by the parties, at least once every six months during the Term, representatives of each of BioForm and Supplier shall hold a meeting in accordance with Sections 4.4 and 8.4 (the “Product Development Meeting”) at which Supplier will present Enhancements for BioForm to consider for application to the Company Product. At such Product Development Meeting, BioForm will also present its marketing plans (pursuant to Section 4.4) for the period and any information or feedback that BioForm reasonably believes may lead to Improvements. Within 30 calendar days following each Product Development Meeting, Supplier shall deliver a notice to BioForm (the “Enhancements Notice”) that shall describe the Enhancements that were presented by Supplier at such Product Development Meeting. Within 30 calendar days following receipt of the Enhancements Notice, BioForm may notify Supplier in writing if BioForm elects that any Enhancement described in the Enhancements Notice shall become an Improvement. If BioForm does provide such notice to Supplier during such 30-calendar day period, then BioForm and Supplier shall agree on a timeline for implementation of the Improvement in new Product Specifications for Company Product. If BioForm does not provide such a notice, said Enhancement shall not be implemented into the Company Product. The Enhancements Notice may also describe any potential Enhancements presented by Supplier at the Product Development Meeting, but BioForm shall not be required to take any action under this Section 8.4 with respect to such potential Enhancements until such time as they are presented by Supplier as Enhancements at a future Product Development Meeting. All Enhancements and potential Enhancement information provided by Supplier shall be considered Supplier Confidential Information. (b) From time to time, each party may request the other party to participate in joint projects to develop Improvements. Neither party is obligated to participate in such projects, and in each **** Certain information on this page has been omitted and filed separately with the Securities and Exchange Commission. Confidential treatment has been requested with respect to the omitted portions. instance, each party’s decision whether to participate will be made in such party’s sole discretion. If both parties mutually agree to participate in such a project (a “Program”), the parties will promptly prepare a mutually agreeable written development agreement specifying the development activities to be performed by and the research and development tasks assigned to each party (the “Development Agreement”). All allocation of Intellectual Property rights with respect to any Program will be set forth in writing in the Development Agreement. (c) In the absence of a Development Agreement, (i) BioForm and Supplier shall retain joint ownership of Intellectual Property rights in which there is joint inventorship by BioForm (or its Affiliates) and Supplier, as determined in accordance with United States patent law, with Supplier’s rights in such joint ownership being subject to the license rights of BioForm under this Agreement, (ii) any Intellectual Property rights related to the Company Products, Enhancements, and Improvements that are created solely by employees or consultants of Supplier during the Term shall be considered to be Intellectual Property rights of Supplier, subject to the license rights of BioForm under this Agreement, and (iii) any Intellectual Property rights related to the Company Products and Improvements that are created solely by employees or consultants of BioForm or any of its Affiliates during the Term shall be considered to be Intellectual Property rights of BioForm. BioForm hereby grants to Supplier a perpetual, royalty free, world-wide, nonexclusive license to Supplier under such Blocking Intellectual Property to make, use, and sell such Intellectual Property outside the Field. “Blocking Intellectual Property” for the purposes of Section 8.4(c)(iii) shall mean Intellectual Property necessary for Supplier to make, use, or sell SA Product.

  • Manufacturing (a) The Supplier shall without limitation be responsible, at no additional cost to the Purchaser, for: sourcing and procuring all raw materials for the Products; obtaining all necessary approvals, permits and licenses for the manufacturing of the Products; providing sufficient qualified staff and workers to perform the obligations under this Purchase Agreement; implementing and maintaining effective inventory and production control procedures with respect to the Products; and handling other matters as reasonably requested by the Purchaser from time to time. (b) The Supplier shall not change any process, material, component, packaging or manufacturing location without the Purchaser’s express prior written approval.

  • Application of Funding Techniques to Programs 6.3.1 The State shall apply the following funding techniques when requesting Federal funds for the component cash flows of the programs listed in sections 4.2 and 4.3 of this Agreement. 6.3.2 Programs Below are programs listed in Section 4.2 and Section 4.3.

  • New Products You agree to comply with NASD Notice to Members 5-26 recommending best practices for reviewing new products.