NFT Minting Clause Samples
NFT Minting
Load Shedding The Distributor may carry out Load Shedding in the following circumstances: (a) Maintenance of Network equipment: if the Distributor wishes to inspect or effect alterations, maintenance, repairs, or additions to any part of the Network, subject to clauses 4.6, 4.8, 4.10, and Schedule 5 as applicable; (b) Permitted by Service Standards: as permitted by the Service Standards, if the Customer has elected to receive an interruptible or otherwise non-continuous supply of electricity; (c) Compliance with instructions from the System Operator: (i) to comply with a request or instruction received from the System Operator in accordance with the Code; or (ii) if communication with the System Operator has been lost, and the Distributor reasonably believes that, had communication with the System Operator been maintained, the Distributor would have received a request or instruction from the System Operator to shed load in accordance with the Code; (d) Maintain security and safety: to maintain the security and safety of the Network in order to: (i) maintain a safe environment, consistent with the Distributor's health and safety policies; (ii) prevent unexpected short term overloading of the Network; (iii) prevent voltage levels rising or falling outside of legal requirements; (iv) manage System Security; and (v) avoid or mitigate damage to the Network or any equipment connected to the Network; (e) Compliance with the Code: to comply with the Code or the law; or (f) Other circumstances: for any other purpose that, in the Distributor’s reasonable opinion, and in accordance with Good Electricity Industry Practice, requires the interruption or reduction of delivery of electricity to any ICP.
Modern Slavery You hereby affirm your compliance with the Modern Slavery ▇▇▇ ▇▇▇▇ and associated guidance. You confirm (a) that you have read, are familiar with and shall not perform an act or omission which is in contravention with, the letter or spirit of the Act; and (b) you carry out regular, meaningful and comprehensive due diligence procedures and have internal policies in place to address any suspected human rights abuse in your business and Group where applicable.
Tariff Elimination 1. Except as otherwise provided in this Agreement, neither Party may increase any existing customs duty, or adopt a new customs duty, on an originating good. 2. Except as otherwise provided in this Agreement, each Party shall progressively eliminate its customs duties on originating goods in accordance with the Tariff Elimination Schedule established in Annex III.04.2. 3. Upon the request of any Party, the Parties shall consult to consider the possibility of accelerating the elimination of customs duties set out in Annex III.04.2 or incorporating into one Party’s Tariff Elimination Schedule goods not subject to the elimination schedule. An agreement between the Parties to accelerate the elimination of a customs duty on a good or to include a good in a Party’s elimination schedule shall supersede any duty rate or staging category determined pursuant to their Schedules for such good when approved by each such Party in accordance with its applicable legal procedures. 4. The agreement adopted based on paragraph 3, regarding the accelerated elimination of a customs duty for an originating good, shall prevail over any customs duty or tariff elimination schedule set out in the Annexes to this Article. 5. Notwithstanding paragraphs 1 and 2, any Party may maintain or increase a customs duty as authorised by the Dispute Settlement Understanding of the WTO, or any other agreement under the WTO Agreement. 6. Originating goods produced in free trade zones in the territory of a Party shall be subject to the most favoured nation treatment (MFN tariff) when imported into the territory of the other Party, except for the products included in Annex III.04.6, which shall benefit from the Tariff Elimination Schedule. 7. The Parties agree that, from the date of entry into force of this Agreement, and in accordance with the functions assigned to the Joint Council in Article I.06.8(a), upon request of either Party, the Joint Council may meet with the purpose of including other goods into Annex III.04.6.
TOOL STORAGE 1. A company shall provide on all construction jobs in towns and cities, and elsewhere where reasonably necessary and practicable (or if requested buy the employee), a suitable and secure waterproof lock-up solely for the purpose of storing employees’ tools, and on multi-storey and major projects the company shall provide, where possible, a suitable lock-up for employees’ tools within a reasonable distance of the work area of large groups of employees. 2. Where an employee is absent from work because of illness or accident and has advised the company in accordance with Clause 33 – Personal Leave of the award, the company shall ensure that the employee’s tools are securely stored during his/her absence.
Sub-Processing 10.1 In respect of any Processing of Personal Data performed by a third party on behalf of a Party, that Party shall: (a) carry out adequate due diligence on such third party to ensure that it is capable of providing the level of protection for the Personal Data as is required by the contract, and provide evidence of such due diligence to the other Party where reasonably requested; and (b) ensure that a suitable agreement is in place with the third party as required under applicable Data Protection Legislation.