Notice for Initial Synchronisation. The Facility Owner shall give CEB not less than 7 (seven) Days’ notice of the time it wishes first to synchronise the Facility to the CEB System following successful completion of the Pre- commissioning tests under Schedule H, as certified and notified by the Independent Engineer. Facility Owner shall develop, design, construct, commission, test, operate, and maintain the Facility in accordance with the Specifications and Standards mentioned in the table below. IEC TS 62804-1 Photovoltaic (PV) modules – Test methods for the detection of potential- induced degradation – Part 1: Crystalline Silicon EN 50380 Datasheet and nameplate information of photovoltaic module. IEC 61215 -1 Terrestrial photovoltaic (PV) modules - Design qualification and type approval- part 1: Tests Requirements IEC 61215 -2 Terrestrial photovoltaic (PV) modules - Design qualification and type approval- part 2: Tests procedures IEC 61701 Salt mist corrosion testing of photovoltaic (PV) modules IEC 61730-1/2 Photovoltaic (PV) module safety qualification Part 1: Requirements for construction Part 2: Requirements for testing IEC 61853-1 Photovoltaic (PV) module performance testing and energy testing – Part 1: Irradiance and temperature performance measurements and power rating IEC 62790 Junction Boxes for photovoltaic modules-Safety requirements and tests IEC 62994 Photovoltaic PV modules through the life cycle- Environmental health and safety (EH&S) risk assessment- General principles and nomenclature IEC TS 62915 Photovoltaic (PV) modules - Type approval, design and safety qualification - Retesting IEC TS 62941 Terrestrial photovoltaic (PV) modules - Guideline for increased confidence in PV module design qualification and type approval IEC TS 62782 Photovoltaic (PV) modules - Cyclic (dynamic) mechanical load testing IEC 62979 Photovoltaic modules - Bypass diode - Thermal runaway test IEC 62894 Data sheet and name plate for photovoltaic inverters IEC 61683 Photovoltaic Systems – Power conditioners – Procedure for measuring efficiency IEC 62109-1 Safety of power converters for use in photovoltaic power systems Part 1: General Requirements IEC 62109-2 Safety of power converters for use in photovoltaic power systems-Part 2: Particular Requirements for inverters IEC 62109-3 Safety of power converters for use in photovoltaic power systems-Part 3: Particular Requirements for Electronic Devices in Combination with Photovoltaic Elements IEC 62891 Maximum Power Point Tracking Efficiency of Grid Connected Photovoltaic Inverters IEC TS 62910 Test Procedure of Low Voltage Ride-Through (LVRT) Measurement for Utility interconnected PV Inverter IEC 62920 EMC Requirements and Test methods for Grid Connected Power Converters applying to Photovoltaic Power Generating units IEC 62116 Test Procedure for islanding prevention measures for Utility connected photovoltaic inverters IEC 60947 Connectors for photovoltaic systems - Safety. IEC 61727 Photovoltaic (PV) systems - Characteristics of the utility interface IEC 61836 Solar photovoltaic energy systems - Terms, definitions and symbols IEC 62093 Balance-of-system components for photovoltaic systems IEC 62446-1 Photovoltaic (PV) systems - Requirements for testing, documentation, and maintenance – Part 1: Grid-connected systems – Documentation, commissioning tests and inspection IEC 61724 (all parts) Photovoltaic System Performance Monitoring IEC TS 63049 Terrestrial photovoltaic (PV) systems – Guidelines for effective quality assurance in PV systems installation, operation and maintenance IEEE P1547 Series of Standards for Interconnection, May, 2003, NREL/CP-560-34003 BS 7354 Code of Practice for Design of high voltage open terminal stations BS 7430 Code of Practice for Protective Earthing of electrical installations EN 50521 Connectors for photovoltaic systems - Safety. IEC 60068-2 Environmental testing of specimen to withstand specific severities of repetitive and non- repetitive nature IEC 60076 Power transformers - ALL PARTS IEC 60228 Conductors of Insulated Cables IEC 60364-1 Electrical installations of buildings - Part 1: Scope, object and fundamental principles IEC ▇▇▇▇▇-▇-▇▇ Electrical installations of buildings. Part 5: Selection and erection of electrical equipment. Chapter 54: Earthing arrangements and protective conductors IEC ▇▇▇▇▇-▇-▇▇ Electrical installations of buildings IEC 60502-1 Power Cables with extruded insulation and their accessories for rated voltages from 1 kV (Um – 1.2 kV) up to 30 kV (Um = 36 kV) Part 1 - Cables for rated voltages for 1 kV (Um=1.2 kV) and 3 kV (Um=3.6 kV) IEC 60664-1 Insulation coordination for equipment within low-voltage systems –Part 1: Principles, requirements and tests IEC 60909-1 Short circuit calculation in three-phase ac systems. IEC 62208 General requirements for empty enclosures for low voltage switchgear and control gear assemblies IEC 62305-3 Protection against lightning, part 3 physical damage and life hazards in structures IEEE C37.90 IEEE Standard for Relays and Relay Systems Associated with Electric Power Apparatus IEC 60529 Degree of protection provided by enclosures IEC ▇▇▇▇▇-▇-▇ Limits - Limits for harmonic current emissions (equipment input current up to and including 16 A per phase) IEC ▇▇▇▇▇-▇-▇ Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection IEC ▇▇▇▇▇-▇-▇ Assessment of emission limits for the connection of the connection of fluctuating installations to MV, HV and EHV power systems IEC ▇▇▇▇▇-▇-▇▇ Electromagnetic compatibility (EMC) - Part 3-11: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems - Equipment with rated current ≤ 75 A and subject to conditional connection. IEC ▇▇▇▇▇-▇-▇ Generic standard -EMC - Susceptibility - Residential, Commercial and Light industry IEC ▇▇▇▇▇-▇-▇ Generic standard - EMC - Emissions - Residential, Commercial and Light industry IEC ▇▇▇▇▇-▇-▇: Electromagnetic compatibility (EMC) - Generic standards - Immunity for power station and substation environments IEC TR ▇▇▇▇▇-▇-▇ Assessment of emission limits for the connection of distorting installations to MV, HV and EHV power systems IEEE519 IEEE Recommended practice and requirements for harmonic control of electric power systems, Institute of Electrical and Electronic Engineers. 1. Interconnection Facilities
Appears in 1 contract
Sources: Interconnection Agreement
Notice for Initial Synchronisation. The Facility Owner shall give CEB not less than 7 (seven) Days’ notice of the time it wishes first to synchronise the Facility to the CEB System following successful completion of the Pre- commissioning tests under Schedule H, as certified and notified by the Independent Engineer. Facility Owner shall develop, design, construct, commission, test, operate, and maintain the Facility in accordance with the Specifications and Standards mentioned in the table below. IEC TS 62804-1 Photovoltaic (PV) modules – Test methods for the detection of potential- induced degradation – Part 1: Crystalline Silicon EN 50380 Datasheet and nameplate information of photovoltaic module. IEC 61215 -1 Terrestrial photovoltaic (PV) modules - Design qualification and type approval- part 1: Tests Requirements IEC 61215 -2 Terrestrial photovoltaic (PV) modules - Design qualification and type approval- part 2: Tests procedures IEC 61701 Salt mist corrosion testing of photovoltaic (PV) modules IEC 61730-1/2 Photovoltaic (PV) module safety qualification Part 1: Requirements for construction Part 2: Requirements for testing IEC 61853-1 Photovoltaic (PV) module performance testing and energy testing – Part 1: Irradiance and temperature performance measurements and power rating IEC 62790 Junction Boxes for photovoltaic modules-Safety requirements and tests IEC 62994 Photovoltaic PV modules through the life cycle- Environmental health and safety (EH&S) risk assessment- General principles and nomenclature IEC TS 62915 Photovoltaic (PV) modules - Type approval, design and safety qualification - Retesting IEC TS 62941 Terrestrial photovoltaic (PV) modules - Guideline for increased confidence in PV module design qualification and type approval IEC TS 62782 Photovoltaic (PV) modules - Cyclic (dynamic) mechanical load testing IEC 62979 Photovoltaic modules - Bypass diode - Thermal runaway test IEC 62894 Data sheet and name plate for photovoltaic inverters IEC 61683 Photovoltaic Systems – Power conditioners – Procedure for measuring efficiency IEC 62109-1 Safety of power converters for use in photovoltaic power systems Part 1Part1: General Requirements IEC 62109-2 Safety of power converters for use in photovoltaic power systems-Part 2: Particular Requirements for inverters IEC 62109-3 Safety of power converters for use in photovoltaic power systems-Part 3: Particular Requirements for Electronic Devices in Combination with Photovoltaic Elements IEC 62891 Maximum Power Point Tracking Efficiency of Grid Connected Photovoltaic Inverters IEC TS 62910 Test Procedure of Low Voltage Ride-Through (LVRT) Measurement for Utility interconnected PV Inverter IEC 62920 EMC Requirements and Test methods for Grid Connected Power Converters applying to Photovoltaic Power Generating units IEC 62116 Test Procedure for islanding prevention measures for Utility connected photovoltaic inverters IEC 60947 Connectors for photovoltaic systems - Safety. IEC 61727 Photovoltaic (PV) systems - Characteristics of the utility interface IEC 61836 Solar photovoltaic energy systems - Terms, definitions and symbols IEC 62093 Balance-of-system components for photovoltaic systems IEC 62446-1 Photovoltaic (PV) systems - Requirements for testing, documentation, and maintenance – Part 1: Grid-connected systems – Documentation, commissioning tests and inspection IEC 61724 (all parts) Photovoltaic System Performance Monitoring IEC TS 63049 Terrestrial photovoltaic (PV) systems – Guidelines for effective quality assurance in PV systems installation, operation and maintenance IEEE P1547 Series of Standards for Interconnection, May, 2003, NREL/CP-560-34003 BS 7354 Code of Practice for Design of high voltage open terminal stations BS 7430 Code of Practice for Protective Earthing of electrical installations EN 50521 Connectors for photovoltaic systems - Safety. IEC 60068-2 Environmental testing of specimen to withstand specific severities of repetitive and non- repetitive nature IEC 60076 Power transformers - ALL PARTS IEC 60228 Conductors of Insulated Cables IEC 60364-1 Electrical installations of buildings - Part 1: Scope, object and fundamental principles IEC ▇▇▇▇▇-▇-▇▇ Electrical installations of buildings. Part 5: Selection and erection of electrical equipment. Chapter 54: Earthing arrangements and protective conductors IEC ▇▇▇▇▇-▇-▇▇ Electrical installations of buildings IEC 60502-1 Power Cables with extruded insulation and their accessories for rated voltages from 1 kV (Um – 1.2 kV) up to 30 kV (Um = 36 kV) Part 1 - Cables for rated voltages for 1 kV (Um=1.2 kV) and 3 kV (Um=3.6 kV) IEC 60664-1 Insulation coordination for equipment within low-voltage systems –Part 1: Principles, requirements and tests IEC 60909-1 Short circuit calculation in three-phase ac systems. IEC 60840 Power cables with extruded insulation and their accessories for rated voltages above 30 kV (Un = 36 kV) up to 150 kV (Un = 170 kV)- Test methods and requirements. IEC 62208 General requirements for empty enclosures for low voltage switchgear and control gear assemblies IEC 62305-3 Protection against lightning, part 3 physical damage and life hazards in structures IEEE C37.90 IEEE Standard for Relays and Relay Systems Associated with Electric Power Apparatus IEC 60529 Degree of protection provided by enclosures IEC ▇▇▇▇▇-▇-▇ Limits - Limits for harmonic current emissions (equipment input current up to and including 16 A per phase) IEC ▇▇▇▇▇-▇-▇ Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection IEC ▇▇▇▇▇-▇-▇ Assessment of emission limits for the connection of the connection of fluctuating installations to MV, HV and EHV power systems IEC ▇▇▇▇▇-▇-▇▇ Electromagnetic compatibility (EMC) - Part 3-11: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems - Equipment with rated current ≤ 75 A and subject to conditional connection. IEC ▇▇▇▇▇-▇-▇ Generic standard -EMC - Susceptibility - Residential, Commercial and Light industry IEC ▇▇▇▇▇-▇-▇ Generic standard - EMC - Emissions - Residential, Commercial and Light industry IEC ▇▇▇▇▇-▇-▇: Electromagnetic compatibility (EMC) - Generic standards - Immunity for power station and substation environments IEC TR ▇▇▇▇▇-▇-▇ Assessment of emission limits for the connection of distorting installations to MV, HV and EHV power systems IEEE519 IEEE Recommended practice and requirements for harmonic control of electric power systems, Institute of Electrical and Electronic Engineers.
1. Interconnection Facilities
Appears in 1 contract
Sources: Interconnection Agreement