Common use of Operation of State Laws Clause in Contracts

Operation of State Laws. In any State in which any statute or regulation relating to apprentices is in force, that statute and regulation will operate in that State provided that the provisions of the statute or regulation are not inconsistent with this Agreement in which case the provisions of this Agreement will apply. (i) Where it is consistent with State Legislation, an apprentice may be engaged under a Training Agreement or Contract of Training approved by the relevant State or Territory Authority, provided the qualification outcome specified in the Training Agreement or Contract of Training is consistent with that established for the vocation in the training package determined from time to time by the Manufacturing Industry Skills Council (MISC) or its successors and endorsed by the relevant Training Authority or, is consistent with the qualifications established for electrical vocations within the relevant electrical/utilities Training Package endorsed by the National Training Quality Council or its successor. (ii) Subject to (a) of this subclause, an apprenticeship may be undertaken in any of the following trades: (1) Engineering Tradesperson (Mechanical) (2) Engineering Tradesperson (Fabrication) (3) Engineering Tradesperson (Electrical/Electronic) (4) Higher Engineering Tradesperson and Advanced Engineering Tradesperson (A) The duration and pay for these apprenticeships are dealt with in Schedule D. (B) The classification on completion of a Higher Engineering Tradesperson apprenticeship will be as a minimum C10. Where the apprentice is offered employment at the completion of their apprenticeship and such employment is in the area of the apprenticeship training, such that they are exercising or will be required to exercise the skills and knowledge gained during their apprenticeship necessary for a C7 level of work they shall be classified at C7. (C) The training program for each Higher Engineering Tradesperson apprentice is to be consistent with the minimum training requirement for the classification of C7 Special Class Tradesperson, as determined from time to time by the Manufacturing Industry Skills Council (MISC), and as endorsed by the National Training Quality Council. Each apprentice shall also complete the requirements for a trade certificate as defined in (c)(i), as part of the training program leading to the completion of the Certificate IV in Engineering. (D) The training program for each Advanced Engineering Tradesperson apprentice is to be consistent with the minimum training requirement for the classification of C5 Advanced Engineering Tradesperson, as determined from time to time by the, Manufacturing Industry Skills Council (MISC), and as endorsed by the National Training Quality Council. Each apprentice shall also complete the requirements for a trade certificate as defined in (c)(i), and a Certificate IV in Engineering as part of the training program leading to the completion of the Diploma of Engineering.

Operation of State Laws. In any State in which any statute or regulation relating to apprentices is in force, that statute and regulation will operate in that State provided that the provisions of the statute or regulation are not inconsistent with this Agreement agreement in which case the provisions of this Agreement agreement will apply. (i) Where it is consistent with State Legislation, an apprentice may be engaged under a Training Agreement or Contract of Training approved by the relevant State or Territory Authority, provided the qualification outcome specified in the Training Agreement or Contract of Training is consistent with that established for the vocation in the training package determined from time to time by the Manufacturing Industry Skills Council (MISC) or its successors and endorsed by the relevant Training Authority or, is consistent with the qualifications established for electrical vocations within the relevant electrical/utilities Training Package endorsed by the National Training Quality Council or its successor. (ii) Subject to (a) of this subclause, an apprenticeship may be undertaken in any of the following trades: (1) Engineering Tradesperson (Mechanical) (2) Engineering Tradesperson (Fabrication) (3) Engineering Tradesperson (Electrical/Electronic) (4) Higher Engineering Tradesperson and Advanced Engineering Tradesperson (A) The duration and pay for these apprenticeships are dealt with in Schedule D. (B) The classification on completion of a Higher Engineering Tradesperson apprenticeship will be as a minimum C10. Where the apprentice is offered employment at the completion of their apprenticeship and such employment is in the area of the apprenticeship training, such that they are exercising or will be required to exercise the skills and knowledge gained during their apprenticeship necessary for a C7 level of work they shall be classified at C7. (C) The training program for each Higher Engineering Tradesperson apprentice is to be consistent with the minimum training requirement for the classification of C7 Special Class Tradesperson, as determined from time to time by the Manufacturing Industry Skills Council (MISC), and as endorsed by the National Training Quality Council. Each apprentice shall also complete the requirements for a trade certificate as defined in (c)(i), as part of the training program leading to the completion of the Certificate IV in Engineering. (D) The training program for each Advanced Engineering Tradesperson apprentice is to be consistent with the minimum training requirement for the classification of C5 Advanced Engineering Tradesperson, as determined from time to time by the, Manufacturing Industry Skills Council (MISC), and as endorsed by the National Training Quality Council. Each apprentice shall also complete the requirements for a trade certificate as defined in (c)(i), and a Certificate IV in Engineering as part of the training program leading to the completion of the Diploma of Engineering.