Common use of Other Traffic Control Methods Clause in Contracts

Other Traffic Control Methods. The posting of CB channel signs may be authorized. On roads listed in CT5.31#, Purchaser may be authorized to install temporary gates, barricades (except cables), or natural barriers. The devices must be installed with the necessary hazard markers, be reasonably passable by Forest Service, and be removed prior to acceptance of the subdivision being served by the road. Part II. Specific Requirements Purchaser shall furnish, install, and maintain “TRUCKS” warning signs prior to and during all periods of log and equipment haul, at the following locations: 1. On National Forest Service Road (NFSR) 45 (Hillock Burn Road) mile post 0.00, at the Junction (Jct) NFSR 4500120 & NFSR 45, facing west. 2. On NFSR 45 (Hillock Burn Road) mile post 0.50, at the Junction (Jct) NFSR 4500130 & NFSR 45, facing east. Purchaser shall furnish, install, and maintain “FOR LOGGING USE ONLY” warning signs prior to and during all periods of log and equipment haul, at the following locations: 1. On NFSR 4500120 at Mile Post 0.00. 2. On NFSR 4500130 at Mile Post 0.00. Contractor shall furnish, install, and maintain “TREE FELLING AHEAD” signs prior to and during all periods of felling “Danger Trees” along all roads. Contractor shall furnish flaggers where & when needed. 1. On all roads where “Danger Trees” are required for felling and/or removal. Name Name Title Title Date Date CT2.11# - TIMBER SUBJECT TO AGREEMENT (06/1972) In addition, there is within Sale Area an unestimated quantity of: that shall be Included Timber upon written agreement. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) All live trees as specified by the designation by description table below or Marked with blue tracer paint for the Individual Tree Mark units (ITM) which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange tracer paint and boundary tags , or identified by N/A are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Table 1. PAYMENT UNIT DESIGNATION BY DESCRIPTION DESIGNATED SPECIES SPACING FEET1/ GAPS 2 ▇▇▇▇▇▇▇-fir, western hemlock 15 Yes 4 ▇▇▇▇▇▇▇-fir, western hemlock 12 Yes 6 All live trees Marked with a horizontal BLUE tracer paint band around it and ▇▇▇▇▇ ▇▇▇▇. ITM - 8 All live trees Marked with a horizontal BLUE tracer paint band around it and ▇▇▇▇▇ ▇▇▇▇. ITM - 10 ▇▇▇▇▇▇▇-fir, western hemlock 15 Yes Payment Units that include Marked trees follow the specifications below: Gaps: Cut all designated species with a minimum 7 inch diameter at ▇▇▇▇▇ height(DSH)2/ within 25 feet1/ measured from DSH2/ of a tree marked with a horizontal YELLOW tracer paint band around the bole and a ▇▇▇▇▇ ▇▇▇▇. Trees marked with YELLOW tracer paint are to be cut. Areas outside of Gaps described above, cut all designated species, with a minimum 7 inch DSH2/, within the DxD spacing1/ measured from ▇▇▇▇▇ height2/ of a live tree with the largest DSH2/. Boundary trees or species other than a designated species which have the largest DSH2/ can be used as the largest tree to designate cut trees. Cut all live trees marked with a horizontal BLUE tracer paint band around the bole and a ▇▇▇▇▇ ▇▇▇▇. 1/ Distances are measured in slope distance, tree face to tree face outside bark at ▇▇▇▇▇ height 2/ or breast height3/ above the natural forest floor on the high or uphill side. The face of the tree is defined as the portion of the bole that is closest to the bole of the tree being measured from.

Other Traffic Control Methods. The posting of CB channel signs may be authorized. On roads listed in CT5.31#, Purchaser may be authorized to install temporary gates, barricades (except cables), or natural barriers. The devices must be installed with the necessary hazard markers, be reasonably passable by Forest Service, and be removed prior to acceptance of the subdivision being served by the road. Page 140C Sale Name: Gruff Part II. Specific Requirements Purchaser shall furnish, install, and maintain “TRUCKS” warning signs prior to and during all periods of log and equipment haul, at the following locations: 1. On National Forest Service Road (NFSR) 45 4500 (Hillock Burn Memaloose Road) mile post 0.0030.58, at the Junction (Jct) NFSR 4500120 Oregon State Highway 224 & NFSR 45, facing west4500. 2. On NFSR 45 4500 (Hillock Burn Memaloose Road) mile post 0.5022.20, at Jct NFSR 4500262 & NFSR 4500, facing west. Purchaser shall furnish, install, and maintain “LOGGING OPERATIONS NEXT <> MILES” warning signs prior to and during all periods of logging operations and log haul, at the Junction following locations: 1. On NFSR 4500 (JctMemaloose Road) NFSR 4500130 & NFSR 45at least 1000-ft. from operations area, facing eastat both ends of operating area, whenever logging operations are landing on the roadway. Purchaser shall furnish, install, and maintain “FOR LOGGING USE ONLY” warning signs prior to and during all periods of log and equipment haul, at the following locations: 1. On NFSR 4500120 4500270 at Mile Post 0.00. 2. On NFSR 4500130 4500044 at Mile Post 0.00. 3. On NFSR 4500280 at Mile Post 0.00. 4. On NFSR 4500310 at Mile Post 0.00. 5. On NFSR 4500320 at Mile Post 0.00. 6. On NFSR 4500340 at Mile Post 0.00. Contractor shall furnish, install, and maintain “TREE FELLING AHEAD” signs prior to and during all periods of felling “Danger Trees” along all roads. Contractor shall furnish flaggers where & when needed. 1. On all roads where “Danger Trees” are required for felling and/or removal. Name Name Title Title Date Date CT2.11# - TIMBER SUBJECT TO AGREEMENT (06/1972) In addition, there is within Sale Area an unestimated quantity of: that shall be Included Timber upon written agreement. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) All live trees as specified by the designation by description table below or Marked with blue tracer paint for the Individual Tree Mark units (ITM) which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange tracer paint, pink tracer paint, or a combination of orange tracer paint and boundary tags , or identified by N/A are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Table DESCRIPTION PURSUANT TO CT2.35# (OPTION 1. ) – INDIVIDUAL TREE DESIGNATION (06/2010) PAYMENT UNIT DESIGNATION BY DESCRIPTION DESIGNATED SPECIES SPECIES* SPACING FEET1/ LSR LEAVE TREES SKIPS GAPS 2 HEAVY THINS 164 DF, WH, NF, PSF 14 - - - - 166 DF, WH 14 - - - - 168 DF, WH, NF, PSF 13 Yes Yes Yes Yes 170 DF, WH 12 Yes - Yes - 172 DF, WH 15 - - - Yes 174 DF, WH 13 - - Yes Yes 176 DF, WH 13 - - Yes - 178 DF, WH 14 Yes - Yes Yes 180 DF, WH 14 Yes - Yes - 182 DF, WH 14 Yes - Yes - 184 DF, WH 16 Yes - Yes - 186 DF, WH 16 Yes - Yes Yes 187 DF, WH 16 Yes Yes Yes - 188 DF, WH 14 Yes Yes Yes - 190 DF, WH 15 Yes Yes Yes Yes 192 DF, WH 14 Yes - Yes Yes *▇▇▇▇▇▇▇-fir-fir (DF), western hemlock 15 Yes 4 (WH), noble fir (NF), Pacific silver fir (PSF) Designation by Description (DxD): Payment Units that include LSR Leave Trees and/or Marked trees follow the specifications below: LSR Leave Trees: Leave all trees greater than or equal to 25.0 inches diameter at ▇▇▇▇▇ height2/. Skips: All trees within 25.0 feet1/ measured from ▇▇▇-fir, western hemlock 12 Yes 6 All live trees ▇▇ height2/ of a tree Marked with a two horizontal BLUE ORANGE tracer paint band bands around it the bole and a ▇▇▇▇▇ ▇▇▇▇▇ shall be retained. ITM - 8 All live trees Marked with a horizontal BLUE tracer paint band around it and ▇▇▇▇▇ ▇▇▇▇. ITM - 10 ▇▇▇▇▇▇▇-fir, western hemlock 15 Yes Payment Units that include Marked trees follow the specifications below: Gaps: Cut all designated species with a minimum 7 7.0 inch diameter at ▇▇▇▇▇ height(DSH)2/ height2/ within 25 25.0 feet1/ measured from DSH2/ ▇▇▇▇▇ height2/ of a tree marked Marked with a horizontal YELLOW tracer paint band around the bole and a ▇▇▇▇▇ ▇▇▇▇. Trees marked Marked with YELLOW tracer paint are to be cut. Heavy Thin: Cut all designated species with a minimum 7.0 inch diameter at ▇▇▇▇▇ height2// within 25.0 feet1/ measured from ▇▇▇▇▇ height2/ of a tree Marked with a horizontal PINK tracer paint band around it and ▇▇▇▇▇ ▇▇▇▇. Trees Marked with PINK tracer paint are to be retained. Areas outside of Gaps Skips, Gaps, and Heavy Thins described above, cut all designated species, with a minimum 7 7.0 inch DSH2/diameter at ▇▇▇▇▇ height2/, within the DxD spacing1/ measured from ▇▇▇▇▇ height2/ of a live tree with the largest DSH2/. ▇▇▇▇▇ diameter2/. Boundary trees or species other than a designated species which have the largest DSH2/ diameter at ▇▇▇▇▇ height2/ can be used as the largest tree to designate cut trees. Cut all live trees marked with a horizontal BLUE tracer paint band around the bole and a ▇▇▇▇▇ ▇▇▇▇. 1/ Distances are measured in slope distance, tree face to tree face outside bark at ▇▇▇▇▇ height 2/ or breast height3/ above the natural forest floor on the high or uphill side. The face of the tree is defined as the portion of the bole that is closest to the bole of the tree being measured from.