Reading Meters Sample Clauses

Reading Meters. (a) The Seller shall, at its own cost and expense, procure and install telemetry and electronic data recording systems capable of recording the Net Delivered Energy measured by the Metering System and procure and install such systems for the Back-Up Metering System on a continuous basis and capable of storing such recordings for not less than ninety (90) Days. All metering data recorded by the Metering System and the Back-up Metering System shall also be telemetered at the System Operator’s control centre through telemetry facilities provisioned by the Seller at its expense. Subject to the provisions of Section 7.4(d) and verification of the data recording system pursuant to Section 7.4(b), the Parties agree that the information contained in or obtained from such electronic data recording and telemetry systems shall be used to determine the Net Delivered Energy. The electronic data recording system and the telemetry system related to the Metering System and the Back-Up Metering System shall constitute a part of the Metering System and the Back- Up Metering System, respectively, for all purposes under this Agreement, and the electronic data recording system and the telemetry system related to the Metering System shall be conveyed to the Purchaser as a part of the Metering System in accordance with the provisions of this Article VII. (b) The information contained in the electronic data recording system shall be verified by checking that the sum of the hourly readings in the electronic data recording system over a specified period are consistent with the local totalized readings for the Metering System (or, if applicable, the Back-Up Metering System) over the same period (determined by subtracting the local totalized reading at the beginning of the period from the local totalized reading at the end of the period). In order to verify the information contained in the electronic data recording system the following procedure shall apply: (i) the local totalized readings of the Metering System and the Back-Up Metering System shall be read on the issuance of Certificate of Readiness for Energization of the Seller Interconnection Facilities and thereafter Monthly on the last Business Day of each Month or such other Day as may be mutually agreed upon by the Parties; (ii) the Purchaser shall take such reading during normal business hours unless otherwise mutually agreed by the Parties; (iii) the Purchaser shall give the Seller at least forty-eight (48) hours notice of...
View SourceView Similar (12)
Reading Meters. The District shall read its meters mentioned in this contract at appropriate intervals so as to maintain a record of energy transactions under this contract.
View Source

Related to Reading Meters

  • Meters 7.1.1 For installation of Meters, Meter testing, Meter calibration and Meter reading and all matters incidental thereto, the SPD and SECI shall follow and be bound by the Central Electricity Authority (Installation and Operation of Meters) Regulations, 2006, the Grid Code, as amended and revised from time to time. 7.1.2 The SPD shall bear all costs pertaining to installation, testing, calibration, maintenance, renewal and repair of meters at SPD’s side of Delivery Point. 7.1.3 In addition to ensuring compliance of the applicable codes, the SPD shall install Main & Check meters at the Delivery Point, along with Stand-by meter(s) as per the applicable Central/State regulations. 7.1.4 In case of pooling of multiple Projects, power from multiple Projects can be pooled at a Pooling Substation prior to the Delivery point and the combined power can be fed at Delivery point through a common transmission line from the Pooling Substation. In such cases, ABT compliant sub-meters as per relevant regulation/approval are also to be set up at pooling substation for individual projects in addition to the meters at Delivery Point as described in clause 7.1.3.

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

  • Delivery Points ‌ Project water made available to the Agency pursuant to Article 6 shall be delivered to the Agency by the State at the delivery structures established in accordance with Article 10.

  • Delivery Point The delivery point is the point of delivery of the Power Product to the CAISO Controlled Grid (the “Delivery Point”). Seller shall provide and convey to Buyer the Power Product from the Generating Facility at the Delivery Point. Title to and risk of loss related to the Power Product transfer from Seller to Buyer at the Delivery Point.

  • Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Freedom has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Freedom. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Freedom (e.g. hairpinning): 1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises. 2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated. 3. If capacity exists, provide "side-door" porting through the switch. 4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch). 2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases. 2.6.3 If no alternate facility is available, and upon request from Freedom, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Freedom will then have the option of paying the one-time SC rates to place the Loop.