Repair or Replace Sample Clauses
POPULAR SAMPLE Copied 1 times
Repair or Replace. The Company will assume the full cost of repairing or replacing uniform items that are damaged during the course of the Cabin Attendant's work, provided that the appropriate form is completed by the Flight Director and that the alterations are done by the designated supplier.
Repair or Replace. If there is a Defect in a MolGen Deliverable and such Defect is attributable to MolGen and under warranty, MolGen may ensure that the Defect is repaired or that the defective item is replaced if this is reasonably possible.
Repair or Replace. As LipoScience’s sole and exclusive remedy for any breaches of the KMC Warranty, KMC will, at KMC’s option, repair or replace without charge, any Instrument manufactured by it, which is found by KMC to be so defective; provided, however, that (a) the Instrument is returned in accordance with KMC’s Return Material Authorization (“RMA”) process, (b) the Instrument, subassembly or component involved is returned by transportation designated by KMC to a location designated by KMC, and at the cost of KMC, and (c) KMC is notified by LipoScience in writing of the defect within thirty (30) days of the expiration of the Warranty Period set forth in Section 12.1 hereof.
Repair or Replace. Developer will repair or replace the System during such WARRANTY PERIOD as soon as possible after Customer informs Developer of any breach of this warranty.
Repair or Replace. During the Warranty Period, ▇▇▇▇▇▇ Engineering will replace or repair any defective Products that were manufactured by ▇▇▇▇▇▇ Engineering without charge, so long as the damage does not arise from:
(a) improper adjustment, calibration, operation, or installation of the Product by the Customer including incorrect installation of the water supply and/or electrical supply system of which the Product forms a part, installation not in accordance with the requirements of the National Construction Code (NCC) Volume 3, AS/NZ 3500.12019, relevant WaterMark and StandardsMark requirements, SAA Wiring Rules AS/NZ 3000, and/or any relevant statutory and local requirements in the State or Territory in which the Product is installed;
(b) installation or part installation by any person other than a licensed plumbing contractor and, where applicable, a licensed electrical contractor;
(c) using the Product, in situations where the water in the plumbing system exceeds the following levels: - Total hardness – 200 mg/litre or p.p.m - Total dissolved solids – 600 mg/litre or p.p.m - Electrical conductivity – 850 µS/cm - Chloride – 250 mg/litre or p.p.m - Magnesium – 10mg/litre or p.p.m - Sodium – 180 mg/litre or p.p.m - pH Level – Min 6.5 to Max 8.5
(d) using the Product, in harsh environments such as in or around pools, salt areas such as oceans and rivers, and areas exposed to chemicals and gases. In these environments, consideration should be given to the use of surface treatments for the Products, such as electropolishing, chrome plating or other coatings.
(e) the use of accessories including consumables, hardware, or software which were not manufactured by, installed by, or approved in writing by ▇▇▇▇▇▇ Engineering;
(f) any contamination, foreign materials, or leakages caused or induced by the Customer;
(g) any modification of the Product which was not authorised in writing by ▇▇▇▇▇▇ Engineering including tampering with or any attempt to disassemble the Product;
(h) any misuse of the Product by the customer or anyone for whom the Customer has legal responsibility (including a minor);
(i) any use or operation of the Product outside of the physical, electrical, or environmental specifications of the Product;
(j) failure for any reason to follow the directions for use given in any user manual, installation instructions or specification data sheet applicable to the Product, including excessive water pressure or temperature outside the installation instructions or application gu...
Repair or Replace. CertiPath may replace or repair the Product with either a new or a reconditioned Product.
Repair or Replace. Contractor through CertiPath may replace or repair the Product with either a new or a reconditioned Product.
Repair or Replace. Riverbed may, in its discretion, replace or repair a Product with either a new or reconditioned Product.
Repair or Replace. During the applicable product warranty period set out in the Bid Document, or, if no product warranty is set out in the Bid Document, for a period of two (2) years following acceptance of the Products by TBDSSAB in accordance with Section 3.2 (“Product Warranty Period”), Vendor shall repair or replace any Product or part which is determined by TBDSSAB, in its sole discretion acting reasonably, to be in breach of the Product warranties set forth in Section 16.2 and Section 16.3, as applicable, and Vendor is solely responsible for paying all costs in any way associated with such repair or replacement.
Repair or Replace. We may, in our sole discretion, either repair or replace the part, and may substitute new or reconditioned materials of equal quality at the time of replacement. If the repair costs exceed the replacement cost, we may replace the defective equipment with new or refurbished equipment substantially equivalent to or with comparable features as the existing equipment, if available. The replacement equipment may have a higher or lower selling price than the original equipment you have.