Security and Validation Procedures Sample Clauses

The Security and Validation Procedures clause establishes the requirements and protocols for safeguarding data and verifying the authenticity of transactions or information within an agreement. It typically outlines the technical and organizational measures that parties must implement, such as encryption standards, access controls, and regular audits, to protect sensitive information. By clearly defining these procedures, the clause helps prevent unauthorized access, data breaches, and fraud, ensuring that all parties adhere to agreed-upon security standards and maintain trust in the integrity of the contractual relationship.
Security and Validation Procedures. The SC shall apply to the Meter Data of the SC Metered Entities that it represents, the security and validation procedures prescribed by the relevant Local Regulatory Authority. If the relevant Local Regulatory Authority has not prescribed any such procedures, the SC shall apply the procedures set forth in the ISO Metering Protocol of the ISO Tariff. Meter Data submitted by an SC for SC Metered Entities shall conform to these standards unless the ISO has, at its discretion, exempted the SC from these standards. l) Section 3.4.1 is amended as follows:
View SourceView Similar (53)
Security and Validation Procedures. The Scheduling Coordinator shall apply to the Meter Data of the Scheduling Coordinator Metered Entities that it represents the security and validation procedures prescribed by the relevant Local Regulatory Authority. If the relevant Local Regulatory Authority has not prescribed any such procedures, the Scheduling Coordinator shall apply the procedures set forth in the CAISO Tariff. Meter Data submitted by a Scheduling Coordinator for Scheduling Coordinator Metered Entities shall conform to these standards unless the CAISO has, at its discretion, exempted the Scheduling Coordinator from these standards.
View SourceView Similar (43)
Security and Validation Procedures. The security measures and the validation, editing and estimation procedures that the CAISO will apply to Meter Data made available to the CAISO by the CAISO Metered Entity shall be as referred to in the CAISO Tariff.
View SourceView Similar (40)
Security and Validation Procedures. The security measures and the validation, editing and estimation procedures that the ISO will apply to Meter Data made available to the ISO by the ISO Metered Entity shall be as referred to in the ISO Tariff.
View SourceView Similar (7)
Security and Validation Procedures. The security measures and the validation, editing and estimation procedures that the ISO CAISO will apply to Meter Data made available to the ISO CAISO by the ISO CAISO Metered Entity shall be as referred to in the ISO CAISO Tariff.
View Source

Related to Security and Validation Procedures

  • Security and Safety A. The Contractor warrants it is and shall remain in compliance with all applicable local, state and federal laws, regulations, codes and ordinances relating to fire, construction, building, health, food service and safety, including but not limited to the Hotel and Motel Fire Safety Act of 1990, Public Law 101-391. The Judicial Council may terminate this Agreement, pursuant to the termination for cause provision set forth herein, without penalty or prejudice if the Contractor fails to comply with the foregoing requirements. B. The Contractor shall assure that each Attendee is advised of all the appropriate precautions that should be taken to provide for the Attendee’s safety while on the Property. The Contractor shall take every reasonable precaution to provide for the security of Attendees and their belongings. C. The Contractor shall immediately advise the Judicial Council’s staff of any known problems that involve the Attendees during the Program including, but not limited to, assaults, burglaries, accidents, and/or illnesses.

  • SUPERVISION AND CONSTRUCTION PROCEDURES 4.3.1 The Contractor shall supervise and direct the Work, using his / her best skill and attention. The Contractor shall be solely responsible for all construction means, methods, techniques, sequences and procedures and for coordinating all portions of the Work under the Contract. All aspects of the Project shall be subject to the inspection and approval of the State. Contractor guarantees to repair, replace, re-execute or otherwise correct any defect in workmanship, materials, or the like that fails to conform to the requirements of this Contract or that appears during the progress of the Work or within one year of final acceptance by the State. 4.3.2 The Contractor shall be responsible to the State for the acts and omissions of his / her employees, Subcontractors and their agents and employees, and other persons performing any of the Work under a contract with the Contractor. 4.3.3 The Contractor shall not be relieved from his / her obligations to perform the Work in accordance with the Contract Documents either by the activities or duties of the Architect in his / her administration of the Contract, or by inspections, tests or approvals required or performed under Paragraph 7.7 by persons other than the Contractor. 4.3.4 The Contractor shall acquaint himself (herself / itself) with the limits of the property or right- of-way of the State and shall not trespass on other property. The Contractor shall adequately protect the project, adjacent property and the public, and shall be responsible for any damage or injury due to the Contractor’s act or neglect, and shall save the State harmless in respect thereto. 4.3.5 All work shall be done in such a manner as not to interfere with the State’s operating functions. Contractor and his employees shall familiarize themselves and comply with all rules and regulations applicable to the project. 4.3.6 The Contractor shall keep the premises free from liens arising out of or from the Project. Contractor shall obtain and submit waivers of liens with a request for a progress or final payment.

  • COMPLIANCE WITH NEW YORK STATE INFORMATION SECURITY BREACH AND NOTIFICATION ACT Contractor shall comply with the provisions of the New York State Information Security Breach and Notification Act (General Business Law Section 899-aa; State Technology Law Section 208).