SHARED DUTIES Sample Clauses

The SHARED DUTIES clause defines the responsibilities and obligations that both parties agree to perform jointly under the agreement. Typically, this clause outlines tasks or standards that require cooperation, such as maintaining confidentiality, complying with applicable laws, or coordinating project milestones. By clearly specifying these mutual duties, the clause helps ensure collaboration, prevent misunderstandings, and promote accountability between the parties.
SHARED DUTIES. Employees in the Tower LOP working as a member of a crew painting towers may be required to perform certain duties of Painter B and below in the Painter LOP, including but not limited to the use of cleaning tools (hand and mechanical) for surface preparation, application of commonly used protective and decorative coatings, the performance of acceptable removal and installation of insulation material, the use of hand and power suspended staging, and the carrying, assembling, and use of different types of scaffolding including tubular rolling. To safely and proficiently perform the work associated with the Tower Maintenance Program, employees will be given training, which may occur solely on the job, in the following procedures:
View SourceView Similar (5)

Related to SHARED DUTIES

  • Extra Duties The Trustee shall be entitled to refuse to approve any Substituted Obligor if, pursuant to the law of the jurisdiction of incorporation of the Substituted Obligor, the assumption by the Substituted Obligor of its obligations hereunder imposes responsibilities on the Trustee over and above those which have been assumed under this Trust Deed.

  • Typical Duties Measures distance points from reference points and marks guidelines on working surface to lay out work. • Determines vertical and horizontal alignment of courses using ▇▇▇▇▇ ▇▇▇, gauge line (tightly stretched cord) and level. • Spreads soft layer of mortar that serves as base and binder for brick or block using trowel. • Breaks or cut bricks or blocks to size, using power or hand tools. • Shapes stone preparatory to setting, using a chisel hammer and other shaping tools. • Applies mortar to end of brick or block and positions same in mortar bed. • Spreads mortar over stone and foundation with trowel and sets stone in place by hand or with aid of a crane. • Removes excess mortar from face using trowel. • Taps brick or block with trowel to level, align and embed in mortar, allowing for specified thickness of joint. • Aligns stone with plumb line and finishes joints between stone with a pointing trowel. • Fastens brick, block, or terra cotta veneer to face of buildings or structures with appropriate ties embedded in mortar between units or in anchor holes in units. • Grouts, insulates, and places all reinforcing rods, anchors, and flashing in masonry walls. • Lays refractory brick, block, and insulation in place by spreading, dipping, or spraying materials to build furnaces, line boilers or like fire resistant structures. • Finishes mortar between brick and block with pointing tool or trowel. • Points, cleans, caulks and waterproofs masonry. • Cleans excess mortar or grout from surface of stone using sponge, brush, water, or acid. Brick Trowel, Pointing trowel, Brick Hammer, 2’’& 4’’ Levels, Standard Square, Speed Square, Sliding T Bevel, Braided Masonry Line, Line pins & Line Blocks, Standard Tape Measure, Brick Spacing & Modular tapes, Gauge Rod, Tuck Pointers. APPENDIX A CLASSIFICATIONS, WAGES & BENEFITS UNION BASE RATE CREDIT UNION PROVISION (See Note b) PENSION FUND HEALTH & WELFARE APPREN- TICESHIP FUND ANNUITY (See Note b) CARPENTERS (Effective (06/01/2023 – 05/31/2024) Group I $ 36.55 (a) $ 2.40 $ 5.66 $ 8.00 $ 0.78 $ 0.50 Group II $ 36.98 (a) $ 2.40 $ 5.66 $ 8.00 $ 0.78 $ 0.50 Group III $ 37.22 (a) $ 2.40 $ 5.66 $ 8.00 $ 0.78 $ 0.50 General ▇▇▇▇▇▇▇: To be negotiated between the GF and the Company but will be at a rate no less than 12% per hour over the Journeyman scale of the classification under his/her supervision.

  • Job Duties It is understood by the parties that every incidental duty connected with operations enumerated in job descriptions is not always specifically described and employees may be required to perform other job-related duties not specifically contained in the job description; however, employees required to perform such duties shall be qualified for the work to be performed.

  • General Duties It shall be the duty of the Owner Trustee to discharge (or cause to be discharged) all of its responsibilities pursuant to the terms of this Agreement and the Sale and Servicing Agreement and to administer the Trust in the interest of the Holder, subject to the Basic Documents and in accordance with the provisions of this Agreement. Notwithstanding the foregoing, the Owner Trustee shall be deemed to have discharged its duties and responsibilities hereunder and under the Basic Documents to the extent the Servicer has agreed in the Sale and Servicing Agreement to perform any act or to discharge any duty of the Trust or the Owner Trustee hereunder or under any Basic Document, and the Owner Trustee shall not be liable for the default or failure of the Servicer to carry out its obligations under the Sale and Servicing Agreement.

  • Basic Duties 1. For each product the basic duty, to which the successive reductions set out in this Agreement are to be applied, shall be the most-favoured-nation rate of duty (MFN rate) applied on 1 January 2000. 2. If, before, by or after entry into force of this Agreement, any tariff reduction is applied on an erga omnes basis, in particular reductions in accordance with commitments resulting from multilateral negotiations under the WTO, such reduced duties shall replace the basic duties referred to in paragraph 1 as from the date when such reductions are applied, or from the entry into force of this Agreement if this is later. 3. The reduced duties calculated in accordance with Article 4(2) (Customs duties on imports and charges having equivalent effect) shall be applied rounded to the first decimal place or, in case of specific duties, to the second decimal place.