Sparing Recommendation and Tools/Consumables Clause Samples

Sparing Recommendation and Tools/Consumables. The Contractor shall perform an analysis that identifies and assesses the tasks that will be required to prepare, maintain, turnaround, disassemble, assemble and test the MK 48 MOD 7 APB6/TI-1 hardware for Contractor/Government testing, in-water testing, preventive maintenance, corrective maintenance and anticipated IMA build-up and maintenance activity. The Contractor shall utilize the results of the analysis to develop hardware sparing recommendations, identify special tools or equipment, and identify anticipated consumable materials or components required to operate, maintain and test the MK 48 MOD 7 APB6/TI-1 hardware (G&C Section and TI-1 WES Kits). The Contractor shall deliver a Hardware Itemized Spares, Tools, and Consumables List (CDRL A049) which encompasses an itemized spares recommendation list, itemized special tools/equipment list, and itemized component and consumables list. The list will be used to support initial provisioning decisions and to assist PMS404 in ensuring that sites designated for testing and operating of the MK 48 MOD 7 APB6/TI-1 hardware are equipped with the necessary spares, tools, and consumable materials. Deliverables: Proposed Spare Part List - Hardware Itemized Spares, Tools and Consumables List (CDRL A049)
View Source

Related to Sparing Recommendation and Tools/Consumables

  • Promotional Materials In the event that the Fund or the Adviser makes available any promotional materials related to the Securities or the transactions contemplated hereby intended for use only by registered broker-dealers and registered representatives thereof by means of an Internet web site or similar electronic means, the Adviser will install and maintain, or will cause to be installed and maintained, pre-qualification and password-protection or similar procedures which are reasonably designed to effectively prohibit access to such promotional materials by persons other than registered broker-dealers and registered representatives thereof.

  • Product Specifications (a) Supplier shall manufacture all Products according to the Specifications in effect as of the date of this Agreement, with such changes or additions to the Specifications of the Products related thereto as shall be requested by Buyer in accordance with this Section or as otherwise agreed in writing by the Parties. All other Products shall be manufactured with such Specifications as the Parties shall agree in writing. (b) Buyer may request changed or additional Specifications for any Product by delivering written notice thereof to Supplier not less than one hundred twenty (120) days in advance of the first Firm Order for such Product to be supplied with such changed or additional Specifications. Notwithstanding the foregoing, if additional advance time would reasonably be required in order to implement the manufacturing processes for production of a Product with any changed or additional Specifications, and to commence manufacture and delivery thereof, Supplier shall so notify Buyer, and Supplier shall not be required to commence delivery of such Product until the passage of such additional time. (c) Supplier shall be required to accommodate any change of, or additions to, the Specifications for any Product, if and only if (i) in Supplier’s good faith judgment, such changed or additional Specifications would not require Supplier to violate good manufacturing practice, (ii) the representation and warranty of Buyer deemed made pursuant to Subsection (e) below is true and correct, and (iii) Buyer agrees to reimburse Supplier for the incremental costs and expenses incurred by Supplier in accommodating the changed or additional Specifications, including the costs of acquiring any new machinery and tooling. For the avoidance of doubt, such costs and expenses shall be payable by Buyer separately from the cost of Products at such time or times as Supplier shall request. (d) Supplier shall notify Buyer in writing within thirty (30) days of its receipt of any request for changed or additional Specifications (i) whether Supplier will honor such changed or additional Specifications, (ii) if Supplier declines to honor such changed or additional Specifications, the basis therefor and (iii) if applicable, the estimated costs and expenses that Buyer will be required to reimburse Supplier in respect of the requested changes or additions, as provided in Subsection (c) above. Buyer shall notify Supplier in writing within fifteen (15) days after receiving notice of any required reimbursement whether Buyer agrees to assume such reimbursement obligation. (e) By its request for any changed or additional Specifications for any Product, Buyer shall be deemed to represent and warrant to Supplier that the manufacture and sale of the Product incorporating Buyer’s changed or additional Specifications, as a result of such incorporation, will not and could not reasonably be expected to (i) violate or conflict with any contract, agreement, arrangement or understanding to which Buyer and/or any of its Affiliates is a party, including this Agreement and any other contract, agreement, arrangement or understanding with Supplier and/or its Affiliates, (ii) infringe on any trademark, service ▇▇▇▇, copyright, patent, trade secret or other intellectual property rights of any Person, or (iii) violate any Applicable Law. Buyer shall indemnify and hold Supplier and its Affiliates harmless (including with respect to reasonable attorneys’ fees and disbursements) from any breach of this representation and warranty.

  • Packaging Materials and Containers for Retail Sale 1. When packaging materials and containers in which a good is packaged for retail sales are classified in the Harmonized System with the good, they shall not be taken into account in determining whether all non-originating materials used in the production of the good undergo the applicable change in tariff classification set out in Annex 4.03. 2. When the good is subject to a requirement of regional value content, the value of these packaging materials and containers shall be taken into account as originating or non-originating materials, as the case may be, in calculating the regional value content of the good.

  • Promotional Material In the event that the Fund or the Investment Adviser makes available any promotional materials related to the Securities or the transactions contemplated hereby intended for use only by registered broker-dealers and registered representatives thereof by means of an Internet web site or similar electronic means, the Investment Adviser will install and maintain or will cause to be installed and maintained, pre-qualification and password-protection or similar procedures which are reasonably designed to effectively prohibit access to such promotional materials by persons other than registered broker-dealers and registered representatives thereof.

  • Training Materials Training Materials will be provided for each student. Training Materials may be used only for either (i) the individual student’s reference during Boeing provided training and for review thereafter or (ii) Customer’s provision of training to individuals directly employed by the Customer.