Stripping and Waxing Clause Samples

Stripping and Waxing. 5.1. When required by Purchaser, Contractor shall provide specialized services, including but not limited to stripping and waxing of floors. Contractor shall utilize the stripping solution approved by the Purchaser and do so in compliance with the manufacturer’s instructions.
View SourceView Similar (6)
Stripping and Waxing. The tile areas will be stripped and waxed quarterly or as needed and requested by the General Services Facility Manager or his/her duly authorized representative using the unit prices per square foot submitted by the Offeror in their Pricing Schedule. The County reserves the right to perform this work independent of the contract.
View Source
Stripping and Waxing. 5.1. When required by Purchaser, Contractor shall provide specialized services, including but not limited to stripping and waxing of floors. Contractor shall utilize the stripping solution 5.2. Stripping: Contractor shall completely remove all dirt, old wax and other foreign substances to return the floor to its original surface. Contractor shall make every effort to prevent streaking or bleaching of floor surface, and shall do so in compliance with the manufacturer's instructions. 5.3. Floor finish removal (stripping) is accomplished when all visible floor surfaces, including surfaces that can be exposed by the removal of non-fixed furnishings have been removed without causing any damage to the floor. Contractor shall remove stripping solution from the floor and surrounding wall areas and ensure dirt, stains, deposits, debris, cleaning solution are removed from the floor.
View Source

Related to Stripping and Waxing

  • SHIPPING AND AIR TRANSPORT 1. Profits of an enterprise of a Contracting State from the operation of ships or aircraft in international traffic shall be taxable only in that State. 2. The provisions of paragraph 1 shall also apply to profits from the participation in a pool, a joint business or an international operating agency.

  • SHIPPING AND SHIPPING COSTS All delivered Equipment and Products must be properly packaged. Damaged Equipment and Products may be rejected. If the damage is not readily apparent at the time of delivery, Supplier must permit the Equipment and Products to be returned within a reasonable time at no cost to Sourcewell or its Participating Entities. Participating Entities reserve the right to inspect the Equipment and Products at a reasonable time after delivery where circumstances or conditions prevent effective inspection of the Equipment and Products at the time of delivery. In the event of the delivery of nonconforming Equipment and Products, the Participating Entity will notify the Supplier as soon as possible and the Supplier will replace nonconforming Equipment and Products with conforming Equipment and Products that are acceptable to the Participating Entity. Supplier must arrange for and pay for the return shipment on Equipment and Products that arrive in a defective or inoperable condition. Sourcewell may declare the Supplier in breach of this Contract if the Supplier intentionally delivers substandard or inferior Equipment or Products.

  • Packaging and Shipping All shipping containers shall be packed and packaged to: (i) ensure safe arrival to final destination; (ii) secure the lowest transportation costs;(iii) comply with requirements of common carriers; (iv) meet Buyer's written instructions; and (v) meet the requirements of all applicable laws, ordinances, rules and regulations.

  • Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.

  • Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.▇▇▇ ▇▇▇▇▇ ▇▇▇▇▇▇▇. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The ▇▇▇▇▇ heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where ▇▇▇▇▇ heights are lower for aesthetic, land treatment, or silvicultural rea- sons.