Common use of Terms and Conditions - Virtual Collocation Clause in Contracts

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ Level 1 safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated Virtual Collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Servicesfinished services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated Virtual Collocated equipment in the Qwest PremisesPremise. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest PremisesPremise. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated Virtual Collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually virtual collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges Direct Training Charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated Virtual Collocated equipment when such equipment is different than the standard equipment used by Qwest in that PremisesPremise. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated Virtual Collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Servicesfinished services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated Virtual Collocated equipment in the Qwest PremisesPremise. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest PremisesPremise. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated Virtual Collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually virtual collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges Direct Training Charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated Virtual Collocated equipment when such equipment is different than the standard equipment used by Qwest in that PremisesPremise. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-vendor- provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges Qwest Version 3.7 Template Agreement, 05-14-2001 Page 77 5-24-2001/bbd/Z-Tel/NE/CDS-010523-0107 incurred in the maintenance and/or repair of CLEC’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated Virtual Collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Servicesfinished services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated Virtual Collocated equipment in the Qwest PremisesPremise. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest PremisesPremise. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated Virtual Collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Bellcore Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually virtual collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges Direct Training Charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated Virtual Collocated equipment when such equipment is different than the standard equipment used by Qwest in that PremisesPremise. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC Sprint will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC Sprint will have physical access to the Demarcation Point in the Qwest Premises. 8.2.2.3 CLEC Sprint will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC Sprint and installed in Qwest Premises. 8.2.2.4 CLEC Sprint shall ensure that upon receipt of CLECSprint’s virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLECSprint’s expense. CLEC Sprint shall advise the manufacturer and seller of the virtually collocated equipment that CLECSprint’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLECSprint’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC Sprint shall provide Qwest interface ni terface specifications (e.g., electrical, functional, physical and software) of CLECSprint’s virtually collocated equipment. Such safety and engineering standards shall apply to CLEC Sprint equipment only to the degree that they apply to Qwest equipment located in ni Premises. Qwest’s Premises.’s 8.2.2.6 CLEC Sprint must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC Sprint will be responsible for payment of Qwest’s initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLECSprint’s virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC Sprint will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLECSprint’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC Sprint shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLECSprint’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ Level 1 safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes reasonable per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated Virtual Collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Servicesfinished services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated Virtual Collocated equipment in the Qwest PremisesPremise. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest Premises.Premise. Qwest Version 3.6 Template Agreement, 03-16-2001 75 4/13/01/HAH for MS/360networks (USA) inc/NE/CDS-010411-0026 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated Virtual Collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Bellcore Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually virtual collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges Direct Training Charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated Virtual Collocated equipment when such equipment is different than the standard equipment used by Qwest in that PremisesPremise. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-vendor- provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, installing and repairing virtually collocated maintaining Virtual Collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Servicesfinished services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC SBCT will not have physical access to the virtually collocated Virtual Collocated equipment in the Qwest PremisesPremise. However, CLEC SBCT will have physical access to the Demarcation Point demarcation point in the Qwest PremisesPremise. 8.2.2.3 CLEC SBCT will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language equipment identified codes) for all equipment provided by CLEC SBCT and installed in Qwest Premises. 8.2.2.4 CLEC SBCT shall ensure that upon receipt of CLECSBCT’s virtually collocated Virtual Collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLECSBCT’s expense. CLEC SBCT shall advise the manufacturer and seller of the virtually collocated equipment that CLECSBCT’s equipment will be possessedcontrolled, installed and maintained by Qwest. 8.2.2.5 CLECSBCT’s virtually collocated equipment must comply with Telcordia Bellcore Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC SBCT shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLECSBCT’s virtually virtual collocated equipment. Such safety and engineering standards shall apply to CLEC SBCT equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC SBCT must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC SBCT will be responsible for payment of Qwest’s initial direct training charges Qwest Direct Training Charges associated with training Qwest employees for the maintenance, operation and installation of CLECSBCT’s virtually collocated Virtual Collocated equipment when such equipment is different than the standard equipment used by Qwest in that PremisesPremise. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC SBCT will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLECSBCT’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC SBCT shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLECSBCT’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated Virtual Collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Servicesfinished services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated Virtual Collocated equipment in the Qwest PremisesPremise. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest PremisesPremise. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated Virtual Collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Bellcore Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ Level 1 safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually virtual collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges Direct Training Charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated Virtual Collocated equipment when such equipment is different than the standard equipment used by Qwest in that PremisesPremise. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s 's virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s 's expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s 's equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s 's virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s 's virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s 's Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s 's initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s 's virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s 's virtually collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s 's virtually collocated equipment where such costs or charges result from Qwest’s 's fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s 's virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s 's expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s 's equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s 's virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s 's virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s 's Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s 's initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s 's virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s 's virtually collocated equipment in accordance with this AgreementAmendment, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s 's virtually collocated equipment where such costs or charges result from Qwest’s 's fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s 's virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s 's expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s 's equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s 's virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s 's virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s 's Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s 's initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s 's virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s 's virtually collocated equipment in accordance with this AgreementAmendment., unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s 's virtually collocated equipment where such costs or charges result from Qwest’s 's fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, and repairing virtually collocated equipment for the purpose of Interconnection or to access UNEs, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwest. 8.2.2.2 CLEC will not have physical access to the virtually collocated equipment in the Qwest Premises. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest Premises. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest Premises. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually collocated equipment must comply with Telcordia Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated equipment when such equipment is different than the standard equipment used by Qwest in that Premises. This includes reasonable per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligence.

Terms and Conditions - Virtual Collocation. 8.2.2.1 Qwest is responsible for installing, maintaining, installing and repairing virtually collocated maintaining Virtual Collocated equipment for the purpose of Interconnection or to access UNEsunbundled loops, ancillary and Finished Services. When providing Virtual Collocation, Qwest shall install, maintain, and repair collocated equipment within the same time periods and with failure rates that are no greater than those that apply to the performance of similar functions for comparable equipment of Qwestfinished services. 8.2.2.2 CLEC will not have physical access to the virtually collocated Virtual Collocated equipment in the Qwest PremisesWire Center. However, CLEC will have physical access to the Demarcation Point demarcation point in the Qwest PremisesWire Center. 8.2.2.3 CLEC will be responsible for obtaining and providing to Qwest administrative codes (e.g., common language codes) for all equipment provided by CLEC and installed in Qwest PremisesWire Center buildings. 8.2.2.4 CLEC shall ensure that upon receipt of CLEC’s virtually collocated Virtual Collocated equipment by Qwest, all warranties and access to ongoing technical support are passed through to Qwest at CLEC’s expense. CLEC shall advise the manufacturer and seller of the virtually collocated equipment that CLEC’s equipment will be possessed, installed and maintained by Qwest. 8.2.2.5 CLEC’s virtually virtual collocated equipment must comply with Telcordia the Bellcore Network Equipment Building System (NEBS) ▇▇▇▇▇ ▇ safety Generic Equipment Requirements TR- NWT-000063, Qwest Wire Center environmental and transmission standards and any statutory (local, state or federal) and/or regulatory requirements in effect at the time of equipment installation or that subsequently become effective. CLEC shall provide Qwest interface specifications (e.g., electrical, functional, physical and software) of CLEC’s virtually virtual collocated equipment. Such safety and engineering standards shall apply to CLEC equipment only to the degree that they apply to Qwest equipment located in Qwest’s Premises. 8.2.2.6 CLEC must specify all software options and associated plug-ins for its virtually collocated equipment. 8.2.2.7 CLEC will be responsible for payment of Qwest’s initial direct training charges Qwest Direct Training Charges associated with training Qwest employees for the maintenance, operation and installation of CLEC’s virtually collocated Virtual Collocated equipment when such equipment is different than the standard equipment used by Qwest in that PremisesCentral Office. This includes per diem charges (i.e., expenses based upon effective Qwest labor agreements), travel and lodging incurred by Qwest employees attending a vendor-provided training course. 8.2.2.8 CLEC will be responsible for payment of reasonable charges incurred in the maintenance and/or repair of CLEC’s virtually virtual collocated equipment in accordance with this Agreement, unless otherwise agreed by the Parties. Notwithstanding the foregoing, CLEC shall not be responsible for any costs or charges incurred in the maintenance and/or repair of CLEC’s virtually collocated equipment where such costs or charges result from Qwest’s fault or negligenceequipment.