Common use of Test bench Clause in Contracts

Test bench. 3.1. The test bench shall be constructed as follows: 3.1.1. a rigid back, fixed, dimensions of which are given in Appendix 1 to this annex; 3.1.2. rigid seating, made from a rigide metal sheet, dimensions of which are given in Appendix 1 to this Annex. The rear part of the seating is made from a rigid sheet metal,. The front part of the seating is also made of a 20 mm diameter tube; 3.1.3. for access to the ISOFIX anchorage system, openings shall be made at the rear of the test bench seat cushion, as prescribed in Appendix 1 to this Annex; 3.1.4. the width of the test bench shall be 800 mm; 3.1.5. the back and the seating shall be covered with polyurethane foam, the characteristics of which are given in Table 1. The dimensions of the cushion are given in Appendix 1 to this annex; Table 1 Standard Value Unit Density EN ISO ▇▇▇ ▇▇-▇▇ Kg/m3 Compression Resistance EN ISO 3386/1 (40% compression) 13 kPa Indentation Load Deflection (ILD) EN ISO 2439B (40% compression) 500 480 (+/15%) N Tensile strenght EN ISO 1798 ≥ 150 kPa Ultimate Elongation EN ISO 1798 ≥ 120 % Compression set EN ISO 1856 (22hr/50%/70°C) ≤ 3 % 3.1.6. The polyurethane foam shall be covered with a sun shade cloth, made of poly-acrylate fibre, the characteristics of which are given in Table 2. Table 2 Specific mass (g/m2) Breaking strength according to DIN 53587 on test specimen 50 mm wide: lengthwise (kg): breadth wise (kg): 290 120 80

Test bench. 3.1. The test bench shall be constructed as follows: 3.1.1. a rigid back, fixed, dimensions of which are given in Appendix 1 to this annex; 3.1.2. rigid seating, made from a rigide metal sheet, dimensions of which are given in Appendix 1 to this Annex. The rear part of the seating is made from a rigid sheet metal,. The front part of the seating is also made of a 20 mm diameter tube; 3.1.3. for access to the ISOFIX anchorage system, openings shall be made at the rear of the test bench seat cushion, as prescribed in Appendix 1 to this Annex; 3.1.4. the width of the test bench shall be 800 mm; 3.1.5. the back and the seating shall be covered with polyurethane foam, the characteristics of which are given in Table 1. The dimensions of the cushion are given in Appendix 1 to this annex; Table 1 Standard Value Unit Density EN ISO ▇▇▇ ▇▇-▇▇ Kg/m3 Compression Resistance EN ISO 3386/1 (40% compression) 13 kPa Indentation Load Deflection (ILD) EN ISO 2439B (40% compression) 500 480 (+/15%) N Tensile strenght EN ISO 1798 ≥ 150 kPa Ultimate Elongation EN ISO 1798 ≥ 120 % Compression set EN ISO 1856 (22hr/50%/70°C) ≤ 3 % 3.1.6. The polyurethane foam shall be covered with a sun shade cloth, made of poly-acrylate fibre, the characteristics of which are given in Table 2. Table 2 Specific mass (g/m2) Breaking strength according to DIN 53587 on test specimen 50 mm wide: lengthwise (kg): breadth wise (kg): 290 120 80