Common use of TEST CUBES Clause in Contracts

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 SFD4 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT For preambles see "Specifications of materials and methods to be used - PW 371" Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Bricks shall be ordered timeously to obtain uniformity in size and colour Section No. 2 SFD4 Bill No. 3 MASONRY Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 41 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 SFD4 28 MD4 BLOCK Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT For preambles see "Specifications of materials and methods to be used - PW 371" Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Bricks shall be ordered timeously to obtain uniformity in size and colour Section No. 2 SFD4 4 MD4 BLOCK Bill No. 3 MASONRY Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 48 13 Slabs propped up not exceeding 1.5m high m2 8 12 14 Leave or form 500mm diameter opening in top of floor slab No 5 7 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 SFD4 39 MD6 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT For preambles see "Specifications of materials and methods to be used - PW 371" Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Bricks shall be ordered timeously to obtain uniformity in size and colour Section No. 2 SFD4 4 MD6 Bill No. 3 MASONRY Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 44 13 Slabs propped up not exceeding 1.5m high m2 8 11 14 Leave or form 500mm diameter opening in top of floor slab No 5 6 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 SFD4 32 MD4 BLOCK Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT For preambles see "Specifications of materials and methods to be used - PW 371" Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Bricks shall be ordered timeously to obtain uniformity in size and colour Section No. 2 SFD4 3 MD4 BLOCK Bill No. 3 MASONRY Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 SFD4 FD4 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT For preambles see "Specifications of materials and methods to be used - PW 371" Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Bricks shall be ordered timeously to obtain uniformity in size and colour Section No. 2 SFD4 FD4 Bill No. 3 MASONRY Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 SFD4 FD4 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT For preambles see "Specifications of materials and methods to be used - PW 371" Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Bricks shall be ordered timeously to obtain uniformity in size and colour Section No. 2 SFD4 4 FD4 Bill No. 3 MASONRY Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc