Unit Installation Clause Samples

Unit Installation. A. Place the first course of units directly on the wall base. Check units for level and alignment. Units shall be within 1/8 inch of level from end to end and from front to back. Adjacent units should be in contact. If possible, begin placing units at the lowest section of the wall. B. Fill all voids between and within the blocks with granular unit fill. Additional unit fill is not required behind the units, but may be placed for the convenience of the contractor. C. Place backfill behind the units in maximum loose lifts of 8 inches and compact. Compact all backfill to a minimum of 95 percent of the maximum dry density (ASTM D698, Standard ▇▇▇▇▇▇▇). Place backfill in successive lifts until level with the top of the facing unit. D. Remove all excess aggregate and other materials from the top of the units before laying up the next course.
View Source
Unit Installation. A. The requisite installation operations shall be carried out by MGTES personnel under management and supervision of Ener1 engineering supervisors. A. The following general and visual inspections shall be performed on site by Ener1 engineering supervisors at the time the equipment is installed. An Ener1 engineering supervisor shall prepare and submit report documentation to MGTES for each of the following items: 1. Visually inspect the exterior and interior of all Unit systems for signs of damage, cleanliness, and foreign objects. 2. Install and assemble all battery modules and other items within the container. If each Unit includes multiple containers, install interconnecting wiring, raceways, ducts, and piping. 3. Verify control, monitoring, and power wiring terminations for correct routing, support, termination, and tightness. 4. Verify sizing and connection of field installed power and ground conductors. 5. Verify that the installation conforms to factory drawings, requirements, and procedures. 6. Verify control logic revision level and verify correct software set points.
View Source
Unit Installation i. Reasonably work with You to minimize aesthetic impacts to Your Home. ii. Take reasonable steps to schedule Sunverge Battery installation at a mutually convenient date and time. iii. Notify You prior to installation if the Sunverge Battery design has to be materially changed so that You can review any such changes and choose whether to remain in, or exit, the Program. iv. Respect Your Property and maintain a safe environment during installation and follow-up inspections and clean up any debris at Your Property caused by Evergy’s installation or inspection activities.
View Source

Related to Unit Installation

  • Equipment Installation In order to meet its obligations under this Agreement, a Party that owns, rents, or leases equipment (the equipment owner) may require installation of such equipment on property owned by another Party (the property owner), provided that the property is being used for an electric utility purpose and that the property owner shall not be required to do so if it would thereby be prevented from performing its own obligations or exercising its rights under this Agreement.

  • Software Installation The AGENCY shall request approval in writing from the COUNTY prior to installation of any software on COUNTY computer equipment. All software installations must be supervised by COUNTY technical support staff and proof of licensing is required. Upon completion, the AGENCY is responsible for reconfiguring the computers back to the original state.

  • Licenses for Permanent Installation The contractor must comply with all State mandatory licensing requirements prior to installation. Questions on licensing requirements should be directed to the State Licensing Board. Contractor must furnish and install all furniture and materials in compliance with all applicable codes, whether local, state, or federal; and that all permits or licenses required for installation will be obtained without cost to the State.

  • Utility Installations Trade Fixtures Alterations 8.3.1 The term “Utility Installations” refers to all floor and window coverings, air and/or vacuum lines, power panels, electrical distribution, security and fire protection systems, communication cabling, lighting fixtures, HVAC equipment, plumbing, and fencing in or on the Premises. The term “Trade Fixtures” shall mean Lessee’s machinery and equipment that can be removed without doing material damage to the Premises. The term “Alterations” shall mean any modification of the improvements, other than Utility Installations or Trade Fixtures, whether by addition or deletion. “Lessee Owned Alterations and/or Utility Installations” are defined as Alterations and/or Utility Installations made by Lessee that are not yet owned by Lessor pursuant to Section 8.4.1.

  • Maintenance Repairs Utility Installations Trade Fixtures and Alterations (a) Subject to the provisions of Paragraphs 2.2 (Lessor’s warranty as to condition), 2.3 (Lessor’s warranty as to compliance with covenants, etc.), 7.2 (Lessor’s obligations to repair), 9 (damage and destruction), and 14 (condemnation), Lessee shall, at Lessee’s sole cost and expense and at all times, keep the Premises and every part thereof in good order, condition and repair, structural and non-structural (whether or not such portion of the Premises requiring repair, or the means of repairing the same, are reasonably or readily accessible to Lessee, and whether or not the need for such repairs occurs as a result of Lessee’s use, any prior use, the elements or the age of such portion of the Premises), including, without limiting the generality of the foregoing all equipment or facilities serving the Premises, such as plumbing, heating, air conditioning, ventilating, electrical, lighting facilities, boilers, fired or unfired pressure vessels, fire sprinkler and/or standpipe and hose or other automatic fire extinguishing system, including fire alarm and/or smoke detection systems and equipment, fire hydrants, fixtures, walls (interior and exterior), foundations, ceilings, roofs, floors, windows, doors, plate glass, skylights, landscaping, driveways, parking lots, fences, retaining walls, signs, sidewalks and parkways located in, on, about, or adjacent to the Premises. Lessee shall not cause or permit any Hazardous Substance to be spilled or released in, on, under or about the Premises (including through the plumbing or sanitary sewer system) and shall promptly, at Lessee’s expense, take all investigatory and/ore remedial action reasonably recommended, whether or not formally ordered or required, for the cleanup of any contamination of, and for the maintenance, security and/or monitoring of, the Premises, the elements surrounding same, or neighboring properties that was caused or materially contributed to by Lessee, or pertaining to or involving any Hazardous Substance and/or storage tank brought onto the premises by or for lessee or under its control. Lessee, in keeping the Premises in good order, condition and repair, shall exercise and perform good maintenance practices. Lessee’s obligations shall include restorations, replacements or renewals when necessary to keep the Promises and all improvements thereon or a part thereof in good order, condition and state of repair. If Lessee occupies the Premises for seven (7) years or more, lessor may require Lessee to repaint the exterior of the buildings on the Premises as reasonably required, but not more frequently than once every seven (7) years. (b) Lessee shall, at Lessee’s sole cost and expense, procure and maintain contracts, with copies to Lessor, in customary form and substance for, and with contractors specializing and experienced in, the inspection, maintenance and service of the following equipment and improvements, if any, located on the Premises: (i) heating, air conditioning and ventilation equipment, (ii) boiler, fired or unfired pressure vessels, (iii) fire sprinkler and/or standpipe and hose or other automatic fire extinguishing systems, including fire alarm and/or smoke detection. (iv) landscaping and irrigation systems, (v) roof covering and drain maintenance and (vi) asphalt and parking lot maintenance.