Test Procedure definition

Test Procedure means all aspects of engine testing including but not limited to the cycle, preconditioning procedures, equipment specifications, calibrations, calculations and other protocols and specifications needed to measure emissions.
View Source
Test Procedure. When the alarm sounds, make your way very quickly, but without running to the nearest fire exit (possibly not main stairway), once outside make your way to the evacuation area outside as marked on the fire information panel in your Room.
View Source
Test Procedure. The driver manually initiates an eCall at various positions; in different traffic environments (see Table 4 above). At several selected locations along the road, representative of the area and with possible low GPS coverage, the driver stops the vehicle at the roadside and manually activates eCall. Log files are stored in the vehicle and in the PSAP and both the driver and the PSAP operator complete a subjective questionnaire containing a standardized value scale for the evaluation after the end of each eCall.
View Source

Examples of Test Procedure in a sentence

  • If preferred, BSE can combine the Test Plan and Test Procedure for each test into a single document.

  • UKPN shall be entitled on not less than three (3) Business Days’ notice to require a retest of the DER Unit, to be conducted in accordance with the DER Commissioning Test Procedure.

  • Flux Power will develop and document a Test Plan and Acceptance Test Procedure and perform integration testing using the software, prototype electronics and enclosure.

  • In the event AT&T determines, after any engineering or any other change by Seller, that Products or Parts do not operate in accordance with the Specifications or fail to meet the Acceptance Test Procedure of Section 9, and upon AT&T's request, Seller shall promptly evaluate any defective Product or Part and shall notify AT&T of the result of its evaluation and its corrective action plan, if needed, within [*] after receipt of such request from AT&T.

  • PHASE 2A: SPECIFICATION In Phase 2A the detailed design specifications are created: External Specification (Final), Technical Specification (Final), Hazard Analysis (Final) and definition of Aspect's Qualification Test Procedure (verification and validation plan for all items identified under the Functional Technical Specification).


More Definitions of Test Procedure

Test Procedure. 8: Time between successful positioning fixes
View Source
Test Procedure means the smoke meter test procedure as specified in section 2193(c).
View Source
Test Procedure means any test, using such testing criteria developed by the Company that the Customer has requested the Company to perform on any Test Product in order to verify whether a Test Product complies with the Prescribed Standards.
View Source
Test Procedure means the preconditioning sequence and smoke opacity measurement processes for determining compliance with section 2182.
View Source
Test Procedure. Either tightly clamp or thermite weld current wire connections to the
View Source
Test Procedure means a series of processes and procedural steps to be taken by Tesna for its provision of the Services, including wafer/final test procedure either to be provided by PixelPlus to Tesna or to be determined by the parties upon mutual consultation. Such Test Procedure shall be communicated and confirmed by the test document.
View Source
Test Procedure. To check sensitivity an anodized aluminium plate is coated with the respective amounts of analyte. To cover the aluminium plate with the said analyte amounts, aqueous solutions of the respective analyte are applied and dried. The amount of analyte is determined by volume and concentration of the applied analyte solutions. Examination of the respective Drugwipe has to be performed at room temperature (20(degree)C - 25(degree)C) in accordance with the instruction sheet. A positive result is indicated by a red colour developing within one (!) minute in the detection zone. In dependance of the concentration present the colour changes between cream white and red. /s/ [ILLEGIBLE] SECURETEC [GRAPHIC OMITTED] Sicherheitstechnologie und Gefahrstoffdetektion GmBH Annex F2 Product-specifications, Demands for transport and stocking -------------------------------------------------------------------------------- Storage conditions: Each Drugwipe kit is packed individually to ensure maximum stability and performance. Performance of Drugwipe can only be guaranteed up to the date for best usage printed on each pack, - if each Drugwipe kit is stored in the original packaging, - at a temperature between +15(degree)C and +25(degree)C (between +59(degree)F and +77(degree)F)
View Source