Design Development Phase Drawings Sample Clauses

The 'Design Development Phase Drawings' clause defines the requirements and expectations for the preparation and submission of drawings during the design development stage of a project. Typically, this clause outlines the level of detail, format, and content that the drawings must include, such as floor plans, elevations, and key systems layouts, to ensure they accurately reflect the evolving design. By specifying these standards, the clause ensures that all parties have a clear and coordinated understanding of the project's design before moving to the next phase, reducing the risk of misunderstandings or costly changes later in the process.
Design Development Phase Drawings. Provide drawings that indicate the scope of work included in the bid package with sufficient detail to enable preparation and review of an accurate cost estimate, including but not limited to, the following descriptions of minimum requirements for a design development submittal, which shall be augmented as necessary to show design intent and to prepare an accurate estimate of construction cost. 7.4.1. Architectural Drawings 7.4.1.1 Floor plans which clearly show: a. Finish schedule b. Principal dimensions c. Wall types clearly identified d. Security zones and perimeters e. Room and door numbers, and a numbering plan for the entire facility f. Sufficient sections and details to enable a reasonable material takeoff g. Contractor-furnished and Owner-furnished equipment list incorporated in layout
View SourceView Similar (2)
Design Development Phase Drawings. Provide preliminary drawings that indicate the scope of work included in the bid package with sufficient detail to enable preparation and review of an accurate cost estimate, including without limitation, the following descriptions of minimum requirements for a design development submittal, which shall be augmented as necessary to show design intent and to prepare an accurate estimate of construction cost in its essentials as to kinds and locations of materials; type of structural, mechanical and electrical systems. A. Architectural Preliminary Drawings 1. Floor plans that clearly show: (a) Finish schedule (b) Principal dimensions (c) Wall types clearly identified (d) Security zones and perimeters (e) Room and door numbers, and a numbering plan for the entire facility (f) Sufficient sections and details to enable a reasonable material takeoff (g) Contractor-furnished and Owner-furnished equipment list incorporated in layout 2. Roof plans that clearly show: (a) Slopes (b) Type of roofing (c) Roof access and pathways (d) Location of any mechanical equipment (e) Sufficient information to determine primary and secondary means of drainage 3. Reflected ceiling plans that clearly show: (a) Ceiling material (b) Access hatches (c) Room numbers (d) Partitions coordinated with the floor plans (e) Mechanical and electrical features coordinated with mechanical and electrical system drawings 4. Elevations that clearly show: (a) Types of surface materials (b) Dimensions from finish floor to tops of walls, ▇▇▇▇▇ and roof lines (c) All openings without dimensions but coordinated with door and window schedules SAMPLE 5. Sections that clearly show: (a) Any security considerations (b) Firewall conditions at tops of walls (c) All essential building parts and materials 6. All door, window, glazing and hardware schedules complete with sufficient detail to show the agreed-upon form and style 7. All items intended to be permanently affixed to the building B. Structural Preliminary Drawings 1. Floor framing and foundations plans that clearly show: (a) Principal dimensions (b) All columns, shear walls, shafts and stairs (c) Coordination of structure with architectural floor plans (d) Sections cut and details to identify the proposed type of foundations (e) Sufficient section and detail bubbles to show where sections and details can be found (f) All major framing members with sizes 2. Roof framing plans that clearly show: (a) Principal dimensions (b) All major framing members with si...
View SourceView Similar (2)
Design Development Phase Drawings. (90%) 1. Comment from Schematic Design submittal review will be incorporated. 2. During the design development phase, ▇▇▇▇ Architects shall coordinate and develop the project drawings with following consultants: a. Landscape Designer, Civil Engineer, Structural Engineer, and Electrical Engineer b. Oversea Local Coordinator for Pavilion, Monument, and Stone Sculptures c. Local Consultant for Outdoor Musical Instruments 3. 90% Design Deliverables: a. Demolition plans identifying items to be demolished and items to be protected in place. b. Proposed Construction plans with Pavilion and Musical Harmony Park including engineering documents & details.
View Source
Design Development Phase Drawings. Provide preliminary drawings that indicate the scope of work included in the bid package with sufficient detail to enable preparation and review of an accurate cost estimate, including without limitation, the following descriptions of minimum requirements for a design development submittal, which shall be augmented as necessary to show design intent and to prepare an accurate estimate of construction cost in its essentials as to kinds and locations of materials; type of structural, mechanical and electrical systems. [Following are the general disciplines applicable to a building structure; conform as applicable to Project] A. Architectural Preliminary Drawings 1. Floor plans that clearly show: (a) Finish schedule (b) Principal dimensions (c) Wall types clearly identified (d) Security zones and perimeters (e) Room and door numbers, and a numbering plan for the entire facility (f) Sufficient sections and details to enable a reasonable material takeoff (g) Furniture and equipment design with Contractor-furnished and Owner-furnished equipment list incorporated in layout 2. Roof plans that clearly show: (a) Slopes (b) Type of roofing (c) Roof access and pathways (d) Location of any mechanical equipment (e) Sufficient information to determine primary and secondary means of drainage 3. Reflected ceiling plans that clearly show: (a) Ceiling material (b) Access hatches (c) Room numbers (d) Partitions coordinated with the floor plans (e) Mechanical and electrical features coordinated with mechanical and electrical system drawings 4. Elevations that clearly show: (a) Types of surface materials (b) Dimensions from finish floor to tops of walls, ▇▇▇▇▇ and roof lines (c) All openings without dimensions but coordinated with door and window schedules 5. Sections that clearly show: (a) Any security considerations (b) Firewall conditions at tops of walls (c) All essential building parts and materials SAMPLE 6. All door, window, glazing and hardware schedules complete with sufficient detail to show the agreed-upon form and style 7. All items intended to be permanently affixed to the building B. Structural Preliminary Drawings 1. Floor framing and foundations plans that clearly show: (a) Principal dimensions (b) All columns, shear walls, shafts and stairs (c) Coordination of structure with architectural floor plans (d) Sections cut and details to identify the proposed type of foundations (e) Sufficient section and detail bubbles to show where sections and details can be found...
View Source

Related to Design Development Phase Drawings

  • Design Development Phase 1.3.1 Based on the approved Schematic Design Documents, model(s) and any adjustments to the Program of Requirements, BIM Execution Plan or Amount Available for the Construction Contract authorized by the Owner, the Architect/Engineer shall prepare, for approval by the Owner and review by the Construction Manager, Design Development Documents derived from the model(s) in accordance with Owner’s written requirements to further define and finalize the size and character of the Project in accordance with the BIM Execution Plan, “Facility Design Guidelines” and any additional requirements set forth in Article 15. The Architect/Engineer shall review the Design Development documents as they are being modeled at intervals appropriate to the progress of the Project with the Owner and Construction Manager at the Project site or other location specified by Owner in the State of Texas. The Architect/Engineer shall utilize the model(s) to support the review process during Design Development. The Architect/Engineer shall allow the Construction Manager to utilize the information uploaded into Owner’s PMIS to assist the Construction Manager in fulfilling its responsibilities to the Owner. 1.3.2 As a part of Design Development Phase, Architect/Engineer shall accomplish model coordination, aggregation and “clash detection” to remove conflicts in design between systems, structures and components. Architect/Engineer shall utilize Owner’s PMIS to accomplish model coordination and collaborate with Construction Manager in the resolution of critical clashes identified by the Construction Manager. Architect/Engineer shall demonstrate and provide written assurance to Owner that conflicts/collisions between models have been resolved. 1.3.3 The Architect/Engineer shall review the Estimated Construction Cost prepared by the Construction Manager, and shall provide written comments. 1.3.4 Before proceeding into the Construction Document Phase, the Architect/Engineer shall obtain Owner’s written acceptance of the Design Development documents and approval of the mutually established Amount Available for the Construction Contract and schedule. 1.3.5 The Architect/Engineer shall prepare presentation materials including an animation derived from the model(s) as defined in “Facility Design Guidelines” at completion of Design Development and if so requested shall present same to the Board of Regents at a regular meeting where scheduled within the state. 1.3.6 The Architect/Engineer shall prepare preliminary recommended furniture layouts for all spaces where it is deemed important to substantiate the fulfillment of program space requirements, or to coordinate with specific architectural, mechanical and electrical elements. 1.3.7 Architect/Engineer shall assist the Owner, if requested, with seeking approval of the Project by the Texas Higher Education Coordinating Board (THECB). Such assistance shall include (i) the preparation of a listing of the rooms and square footages in the Project, and (ii) the preparation of project cost information, in accordance with THECB Guidelines. This information shall be provided at the completion of the Design Development Phase when requested by the Owner. The listing of rooms and square footages shall then be updated to reflect any changes occurring during construction and provided to the Owner at Substantial Completion. 1.3.8 At the completion of the Design Development Phase, or such other time as Owner may specify to Architect/Engineer, at Owner’s sole option and discretion, Owner will furnish Architect/Engineer with a Guaranteed Maximum Price proposal prepared by Construction Manager based upon the Design Development documents prepared by the Architect/Engineer and approved by the Owner. The Architect/Engineer shall assist the Owner and endeavor to further and advocate the Owner’s interests in Owner’s communications with the Construction Manager in an effort to develop a Guaranteed Maximum Price proposal acceptable to Owner, in Owner’s sole option and discretion. If the Owner does not accept the Construction Manager’s Guaranteed Maximum Price proposal, the Architect/Engineer shall participate with the Owner and Construction Manager in constructability reviews and shall revise the documents as necessary in order to reach an agreement. If the Construction Manager’s Guaranteed Maximum Price proposal exceeds the Schematic Design Phase Estimated Construction Cost prepared by, or otherwise accepted by the Construction Manager due to an increase in the scope of the Project caused by further development of the design documents by the Architect/Engineer to the extent that such could not be reasonably inferred by the Construction Manager from the Schematic Design documents, and Owner directs Architect/Engineer to revise the documents, the Architect/Engineer shall revise the documents at its own expense so that the Guaranteed Maximum Price proposal for constructing the Project shall not exceed the Owner’s Amount Available for the Construction Contract and any previously approved Estimated Construction Costs. If it is determined to be in the Owner’s best interest, instead of requiring the Architect/Engineer to revise the Drawings and Specifications, the Owner reserves the right to accept a Guaranteed Maximum Price proposal that exceeds the stipulated Amount Available for the Construction Contract. The Architect/Engineer shall analyze the final Guaranteed Maximum Price proposal document, together with its supporting assumptions, clarifications, and contingencies, and shall submit a detailed written analysis of the document to the Owner. Such analysis shall include, without limitation, reference to and explanation of any inaccurate or improper assumptions and clarifications. The A/E will not be required to make revisions to the documents at its own expense under the provisions of this paragraph if the Owner’s rejection of the Guaranteed Maximum Price proposal is not due to a failure of the A/E to provide the services otherwise required herein. 1.3.9 After the Guaranteed Maximum Price has been accepted, the Architect/Engineer shall incorporate necessary revisions into the Design Development documents. The A/E will not be required to make revisions to the documents at its own expense under the provisions of this paragraph if the revisions are required as the result of inaccurate assumptions and clarifications made in the development of the Guaranteed Maximum Price proposal that are not due to a failure of the A/E to provide the services otherwise required herein.

  • Development Phase contractual phase initiated with the approval of ANP for the Development Plan and which is extended during the Production Phase while investments in ▇▇▇▇▇, equipment, and facilities for the Production of Oil and Gas according to the Best Practices of the Oil Industry are required.

  • Final Working Drawings After the Final Space Plan has been approved by Landlord, Tenant shall supply the Engineers with a complete listing of standard and non-standard equipment and specifications, including, without limitation, B.T.U. calculations, electrical requirements and special electrical receptacle requirements for the Premises, to enable the Engineers and the Architect to complete the “Final Working Drawings” (as that term is defined below) in the manner as set forth below. Upon the approval of the Final Space Plan by Landlord and Tenant, Tenant shall cause the Architect and the Engineers to complete the architectural and engineering drawings for the Premises, and Architect shall compile a fully coordinated set of architectural, structural, mechanical, electrical and plumbing working drawings in a form which is complete to allow subcontractors to bid on the work, to the extent applicable, and to obtain all applicable permits (collectively, the “Final Working Drawings”) and shall submit the same to Landlord for Landlord’s approval, which approval shall not be unreasonably withheld. Tenant shall supply Landlord with four (4) hard copies and one (1) electronic copy of such Final Working Drawings. Landlord shall advise Tenant within ten (10) business days after Landlord’s receipt of the Final Working Drawings for the Premises if the same are approved, or, if the Final Working Drawings are not reasonably satisfactory or are incomplete in any respect, disapproved, in which event Landlord shall include in its notice of disapproval a reasonably detailed explanation as to which items are not satisfactory or complete and the reason(s) therefor. If Tenant is so advised that the Final Working Drawings are not satisfactory or complete, Tenant shall promptly revise the Final Working Drawings in accordance with such review and any disapproval of Landlord in connection therewith, and Landlord shall approve or disapprove the resubmitted Final Working Drawings, based upon the criteria set forth in this Section 3.3, within five (5) business days after Landlord receives such resubmitted Final Working Drawings. Such procedure shall be repeated until the Final Working Drawings are approved; provided, however, that if Landlord fails to notify Tenant of Landlord’s approval or disapproval of any iteration of the Final Working Drawings within the initial ten (10) business day review period or any subsequent five (5) business day review period for approval or disapproval thereof, Tenant shall deliver Landlord an additional notice requesting approval and if Landlord thereafter fails to respond within five (5) business days of receipt of such additional notice, Landlord will be deemed to have approved such iteration of the Final Working Drawings.

  • Design Development An interim step in the design process. Design Development documents consist of plans, elevations, and other drawings and outline specifications. These documents will fix and illustrate the size and character of the entire project in its essentials as to kinds of materials, type of structure, grade elevations, sidewalks, utilities, roads, parking areas, mechanical and electrical systems, and such other work as may be required.

  • Design Phase All Basic Services set forth in the Agreement with the exception of Interdisciplinary Document Coordination Review, conducting a Card Trick session, Value-Engineering services, Estimating services. • All Basic Services set forth in the Agreement. • All Basic Services set forth in the Agreement. • All Basic Services set forth in the Agreement.