DESIGN, PERMITTING and INSTALLATION Clause Samples

DESIGN, PERMITTING and INSTALLATION. 4.1 The Customer and the System must comply with all applicable requirements of the following; the most current versions of cited references apply: • All applicable building and zoning ordinances and codes • National Electric Code (NEC) requirements, including, but not limited to NEC Articles 690 and 705 • All applicable Underwriters Laboratories (UL) equipment certification requirements including, but not limited to UL 1741 and UL 1741 supplement A (including certifications of compliance with (“Smart” inverter requirements mandated under California Rule 21 for Phase 1,2 & 3 functions). • All applicable Institute of Electrical and Electronics Engineers (IEEE) requirements including, but not limited to the IEEE 1547-series (includes 1547.a, and 1547.1) . • All applicable National Fire Protection Agency (NFPA) requirements, including, but not limited to NFPA 70. At its sole expense, the Customer must: 1) Obtain all necessary zoning permits for the installation of the System. 2) Obtain all necessary electrical & building permit(s) for the installation of the System 3) Obtain and maintain any governmental authorizations or permits that may be required for the installation or operation of the System. 4) Have the design of its System (including all related equipment specifications and installation plans) reviewed and approved by a Professional Electrical Engineer that is currently licensed in the State of Iowa. The Customer must reimburse AMES for any and all losses, damages, claims, penalties, or liability AMES incurs as a result of the Customer’s failure to obtain or to maintain any governmental authorizations and permits that may be required for construction and operation of the Customer’s System. 4.2 The Customer or its designated representative (engineer, consultant, or contractor, for example) must complete Exhibits A and B and construct the System as specified in the completed/attached Exhibit A.
View Source
DESIGN, PERMITTING and INSTALLATION. 4.1 The Customer and the System must comply with all applicable requirements of the following; the most current versions of cited references apply: • All applicable building and zoning ordinances and codes • National Electric Code (NEC) requirements, including, but not limited to NEC Articles 690 and 705 • All applicable Underwriters Laboratories (UL) equipment certification requirements including, but not limited to ▇▇ ▇▇▇▇ , ▇▇ ▇▇▇▇ supplement A and UL 1741 (2016) certification requirements, including certifications of compliance with required advanced/smart inverter requirements mandated in Hawaii and California (i.e. California Phase1 autonomous inverter behaviors). • All applicable Institute of Electrical and Electronics Engineers (IEEE) requirements including, but not limited to the IEEE 1547-series (includes 1547.a, and 1547.1) . • All applicable National Fire Protection Agency (NFPA) requirements, including, but not limited to NFPA 70. At its sole expense, the Customer must: 1) Obtain all necessary zoning permits for the installation of the System. 2) Obtain all necessary electrical & building permit(s) for the installation of the System 3) Obtain and maintain any governmental authorizations or permits that may be required for the installation or operation of the System. 4) Have the design of its System (including all related equipment specifications and installation plans) reviewed and approved by a Professional Electrical Engineer that is currently licensed in the State of Iowa. The Customer must reimburse AMES for any and all losses, damages, claims, penalties, or liability AMES incurs as a result of the Customer’s failure to obtain or to maintain any governmental authorizations and permits that may be required for construction and operation of the Customer’s System. 4.2 The Customer or its designated representative (engineer, consultant, or contractor, for example) must complete Exhibits A and B and construct the System as specified in the completed/attached Exhibit A.
View Source

Related to DESIGN, PERMITTING and INSTALLATION

  • Removal of Improvements All alterations, additions and other improvements by Tenant shall become the property of Landlord and shall not be removed from the Premises, unless request is made by Landlord to Tenant to remove those alterations, additions and other improvements which were made without Landlord's approval where such approval was required under this Lease. All moveable trade fixtures, furniture, furnishings and signs installed in the Premises by Tenant and paid for by Tenant, shall remain the property of Tenant and may be removed upon the expiration of the term of this Lease; provided that any of such items as are affixed to the Premises and require severance may be removed only if Tenant repairs any damage caused by such removal and that Tenant shall otherwise comply with all of the terms, conditions and covenants to be performed by Tenant under this Lease with respect to such removal. If Tenant fails to remove such items from the Premises by the expiration of the Lease Term or earlier termination of this Lease, all such trade fixtures, furniture, furnishings and signs shall become the property of Landlord, unless Landlord elects to require their removal, in which case Tenant shall, at its sole cost and expense, promptly remove the same and restore the Premises to its condition on the date of this Lease. The covenants contained in this Section shall survive the expiration of the Lease Term or earlier termination hereof.

  • Maintenance Repairs Utility Installations Trade Fixtures and Alterations (a) Subject to the provisions of Paragraphs 2.2 (Lessor’s warranty as to condition), 2.3 (Lessor’s warranty as to compliance with covenants, etc.), 7.2 (Lessor’s obligations to repair), 9 (damage and destruction), and 14 (condemnation), Lessee shall, at Lessee’s sole cost and expense and at all times, keep the Premises and every part thereof in good order, condition and repair, structural and non-structural (whether or not such portion of the Premises requiring repair, or the means of repairing the same, are reasonably or readily accessible to Lessee, and whether or not the need for such repairs occurs as a result of Lessee’s use, any prior use, the elements or the age of such portion of the Premises), including, without limiting the generality of the foregoing all equipment or facilities serving the Premises, such as plumbing, heating, air conditioning, ventilating, electrical, lighting facilities, boilers, fired or unfired pressure vessels, fire sprinkler and/or standpipe and hose or other automatic fire extinguishing system, including fire alarm and/or smoke detection systems and equipment, fire hydrants, fixtures, walls (interior and exterior), foundations, ceilings, roofs, floors, windows, doors, plate glass, skylights, landscaping, driveways, parking lots, fences, retaining walls, signs, sidewalks and parkways located in, on, about, or adjacent to the Premises. Lessee shall not cause or permit any Hazardous Substance to be spilled or released in, on, under or about the Premises (including through the plumbing or sanitary sewer system) and shall promptly, at Lessee’s expense, take all investigatory and/ore remedial action reasonably recommended, whether or not formally ordered or required, for the cleanup of any contamination of, and for the maintenance, security and/or monitoring of, the Premises, the elements surrounding same, or neighboring properties that was caused or materially contributed to by Lessee, or pertaining to or involving any Hazardous Substance and/or storage tank brought onto the premises by or for lessee or under its control. Lessee, in keeping the Premises in good order, condition and repair, shall exercise and perform good maintenance practices. Lessee’s obligations shall include restorations, replacements or renewals when necessary to keep the Promises and all improvements thereon or a part thereof in good order, condition and state of repair. If Lessee occupies the Premises for seven (7) years or more, lessor may require Lessee to repaint the exterior of the buildings on the Premises as reasonably required, but not more frequently than once every seven (7) years. (b) Lessee shall, at Lessee’s sole cost and expense, procure and maintain contracts, with copies to Lessor, in customary form and substance for, and with contractors specializing and experienced in, the inspection, maintenance and service of the following equipment and improvements, if any, located on the Premises: (i) heating, air conditioning and ventilation equipment, (ii) boiler, fired or unfired pressure vessels, (iii) fire sprinkler and/or standpipe and hose or other automatic fire extinguishing systems, including fire alarm and/or smoke detection. (iv) landscaping and irrigation systems, (v) roof covering and drain maintenance and (vi) asphalt and parking lot maintenance.

  • Licenses for Permanent Installation The contractor must comply with all State mandatory licensing requirements prior to installation. Questions on licensing requirements should be directed to the State Licensing Board. Contractor must furnish and install all furniture and materials in compliance with all applicable codes, whether local, state, or federal; and that all permits or licenses required for installation will be obtained without cost to the State.

  • Provision and Removal of Equipment B2.1 The Contractor shall provide all the Equipment necessary for the supply of the Services.

  • Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract. a. The contractor shall notify all potential subcontractors and suppliers and lessors of their EEO obligations under this contract. b. The contractor will use good faith efforts to ensure subcontractor compliance with their EEO obligations.