Gas temperature and pressure Sample Clauses

The "Gas temperature and pressure" clause defines the specific conditions under which gas must be delivered or measured, focusing on its temperature and pressure at the point of transfer. Typically, this clause will specify standard reference values, such as a set temperature in degrees Celsius and a pressure in kilopascals or pounds per square inch, to ensure consistency in volume and energy calculations. By standardizing these parameters, the clause ensures accurate measurement and fair transactions, preventing disputes that could arise from variations in gas properties due to differing environmental or operational conditions.
Gas temperature and pressure. (a) The minimum and maximum temperatures and the minimum and maximum pressures at which the Shipper may Deliver Gas to the Operator at the Inlet Points, and the Operator may Deliver Gas to the Shipper at the Outlet Points, are those set out in Item 2 of Schedule 3. (b) The Parties may at any time agree in writing to vary any one or more of the pressures and temperatures set out in Item 2 of Schedule 3. (c) If at any time: (i) the minimum and the maximum temperature and the minimum and maximum pressure of an Inlet Point or an Outlet Point are not set out in Item 2 of Schedule 3; and (ii) the Shipper Delivers Gas to the Operator at that Inlet Point or the Shipper Receives Gas from the Operator at that Outlet Point, then the Shipper is entitled to Deliver Gas at that Inlet Point or obliged to Receive Gas at that Outlet Point under this Contract, (iii) if the Operator is then Receiving Gas from or Delivering Gas to other shippers at that Inlet Point or Outlet Point, at the temperature and pressure at which the Operator is Receiving Gas from or Delivering Gas to those other shippers; or (iv) if the Operator is not then Receiving Gas from or Delivering Gas to other shippers at that Inlet Point or Outlet Point, at the temperature and pressure at which the Operator was last entitled to Deliver Gas or obliged to Receive Gas at that Inlet Point or Outlet Point under the terms of a contract with any other shipper.
View SourceView Similar (11)
Gas temperature and pressure. ‌ (a) The minimum and maximum temperatures and the minimum and maximum pressures at which the Shipper may Deliver Gas to the Owner at the Inlet Points, and the Owner may Deliver Gas to the Shipper at the Outlet Points, are those set out in Item 2 of Schedule 2. (b) The Parties may at any time agree in writing to vary any one or more of the pressures and temperatures set out in Item 2 of Schedule 2. (c) The Shipper acknowledges that its Maximum Interruptible Capacity at each Inlet Point and Outlet Point is dependent upon the gas composition and temperature meeting the requirements set out in Schedule 2.
View Source
Gas temperature and pressure. (a) The minimum and maximum temperatures and the minimum and maximum pressures at which the Shipper may Deliver Gas to the Operator at the Inlet Points, and the Operator may Deliver Gas to the Shipper at the Outlet Points, are those set out in Item 2 of Schedule 3. (b) The Parties may at any time agree in writing to vary any one or more of the pressures and temperatures set out in Item 2 of Schedule 3. (c) If at any time: (i) the minimum and the maximum temperature and the minimum and maximum pressure of an Inlet Point or an Outlet Point are not set out in Item 2 of Schedule 3; and (ii) the Shipper Delivers Gas to the Operator at that Inlet Point or the Shipper Receives Gas from the Operator at that Outlet Point, then the Shipper is entitled to Deliver Gas at that Inlet Point or obliged to Receive Gas at that Outlet Point under this Contract,
View Source

Related to Gas temperature and pressure

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Calibration The comparison of a measurement system or device of unverified accuracy with a measurement system of known and greater accuracy to detect deviation of the unverified measurement system from required performance specifications (of the unverified measurement system or device) and to quantify all measured values to applicable units of the international system of units.

  • Gas If Customer has selected a Gas Fixed Rate, Customer’s Price will be based on the Fixed Rate(s), plus the Administration Charge, set forth in the Application, which includes RITERATE ENERGY’s compressor fuel and transportation charges, administrative and transaction costs and the Gas Balancing Amount and any Regulatory Charges (defined below).

  • Meters (a) You must allow safe and unhindered access to your premises for the purposes of reading and maintaining the meters (where relevant). (b) We will use our best endeavours to ensure that a meter reading is carried out as frequently as is needed to prepare your bills, consistently with the metering rules and in any event at least once every 12 months.