Heat Exchanger Clause Samples

POPULAR SAMPLE Copied 1 times
Heat Exchanger. Heat Exchanger shall be cage type and made of copper/stainless steel tubes of grade X04Cr19Ni9 or X07Cr18Ni9 of IS: 1570(part 5)/1985 .Heat exchangers shall have a minimum of 0.24 sq. meters heat transfer area per 100 LPD capacities.
View Source
Heat Exchanger. The heat exchanger shall bear the ASME “H” stamp for 160 psi working pressure and shall be National Board listed. The heat exchanger shall be constructed of a fully welded 316L stainless steel and of fire tube design. The heat exchanger shall be designed for a single-pass water flow to limit the water side pressure drop.
View Source
Heat Exchanger. The Heat Exchanger is a purchased item modified specifically for use with the NovaRay system. It serves to establish temperature regulation of the water used to cool system components such as the x-ray source and deflection amplifier assembly. Specifications are: [***]
View Source
Heat Exchanger. The heat exchanger shall be a commercially available heat exchanger with a capacity of at least 400kW. The geothermal water would be connected to a heat exchanger located in the vicinity of the building. The flat plate-type high capacity heat exchanger would be used to transfer the thermal energy from geothermal water to regular city water obtained from the city network. The temperature regimes of the heat exchanger would be controlled and monitored by a special microprocessor control unit. The control unit would regulate heat losses by regulating the temperature of discharge water in the interval of 20-250C. The heat exchanger is maintenance-free and may require cleaning of its interior surfaces once a year.
View Source
Heat Exchanger. The Heat Exchanger shall be constructed with copper tubes mechanically bonded to aluminium fins to form a cross fan coil and larger surface area. Architect: ▇▇▇▇▇▇▇ ▇.▇▇▇▇▇▇ [37] Signature & Seal of Tenderer M/S “STUDIO 919 Architects” The fins shall have anticorrosion treatment for Heat Exchanger Coil. The treatment shall be suitable for areas of high pollution, moisture and salt laden air. The casings, fans, motors etc. shall also be with anticorrosion treatment as a standard features. The unit shall be provided with necessary number of direct driven low noise level propeller type fans arranged for vertical / horizontal discharge. Each fan shall have a safety guard.
View Source
Heat Exchanger. 9.5.1 Plumb the unit to a water-to-water heat exchanger with sufficient capacity to draw off heat at the maximum rate anticipated. Route hoses, electrical cables and instrument wires in a manner that does not influence the weighing accuracy of the scale as indicated by placing dead weights on the platform and verifying the scale’s accuracy. 9.5.2 Locate thermocouples to measure the water temperature at the inlet and outlet of the load side of the heat exchanger. 9.5.3 Install a thermopile meeting the requirements of 6.3 to measure the water temperature difference between the inlet and outlet of the load side of the heat exchanger. 9.5.4 Install a calibrated water flow meter in the heat exchanger load side supply line. The water flow meter is to be installed on the cooling water inlet side of the heat exchanger so that it will operate at the temperature at which it is calibrated. 9.5.5 Place the heat exchanger in a box with 2 in. (50 mm) of expanded polystyrene (EPS) foam insulation surrounding it to minimize heat losses from the heat exchanger. 9.5.6 The reported efficiency and heat output rate shall be based on measurements made on the load side of the heat exchanger. 9.5.7 Temperature instrumentation per 6.6 shall be installed in the appliance outlet and return lines. The average of the outlet and return water temperature on the supply side of the system shall be considered the average appliance temperature for calculation of heat storage in the appliance (TFavg and TIavg). Installation of a water flow meter in the supply side of the system is optional.
View Source

Related to Heat Exchanger

  • Trading Facilities Most open-outcry and electronic trading facilities are supported by computer-based component systems for the order-routing, execution, matching, registration or clearing of trades. As with all facilities and systems, they are vulnerable to temporary disruption or failure. Your ability to recover certain losses may be subject to limits on liability imposed by the system provider, the market, the clearing house and/or member firms. Such limits may vary; you should ask the firm with which you deal for details in this respect.

  • Infrastructure Modification of the location and/or sizing of the infrastructure for the Project that does not materially change the functionality of the infrastructure.

  • External Hosting Facilities DST shall implement controls, consistent with applicable prevailing industry practices and standards, regarding the collection, use, storage and/or disclosure of Fund Data by an external hosting provider.

  • Network Interconnection Methods 3.1 The Interconnection provided herein may not be used solely for the purpose of originating a Party’s own interexchange traffic.

  • Secondary Market Trading and Standard & Poor’s If the Company does not maintain the listing of the Public Securities on Nasdaq or another national securities exchange, the Company will (i) apply to be included in Standard & Poor’s Daily News and Corporation Records Corporate Descriptions for a period of five years from the consummation of a Business Combination, (ii) take such commercially reasonable steps as may be necessary to obtain a secondary market trading exemption for the Company’s securities in the State of California and (iii) take such other action as may be reasonably requested by the Representative to obtain a secondary market trading exemption in such other states as may be requested by the Representative; provided that no qualification shall be required in any jurisdiction where, as a result thereof, the Company would be subject to service of general process or to taxation as a foreign corporation doing business in such jurisdiction.