Inscriptions Sample Clauses
Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb2:
2.3.1.1. The trade name or mark of the applicant;
2.3.1.2. The rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed 7.5 mm;
2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament lamps); this need not be indicated separately if it is part of the international designation of the relevant filament lamp category;
2.3.1.5. A space of sufficient size to accommodate the approval mark.
2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Halogen filament lamps meeting the requirements of paragraph 3.7. below shall be marked with a "U".
2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.
Inscriptions. 2.3.1. Gas-discharge light sources submitted for approval shall bear on the cap or bulb:
2.3.1.1. the trade name or ▇▇▇▇ of the applicant;
2.3.1.2. the international designation of the relevant category;
2.3.1.3. the rated wattage; this need not to be indicated separately if it is part of the international designation of the relevant category;
2.3.1.4. a space of sufficient size to accommodate the approval ▇▇▇▇.
2.3.2. The space mentioned in paragraph 2.3.1.4. shall be indicated in the drawings accompanying the application for approval.
2.3.3. Other inscriptions than those covered by paragraphs 2.3.1. and 2.4.4. may be affixed on the cap.
2.3.4. The ballast used for the type approval of the light source shall be marked with type and trade ▇▇▇▇ identification and with the rated voltage and wattage, as indicated on the relevant lamp data sheet,
Inscriptions. 2.3.1. Filament lLight sources submitted for approval shall bear on the cap or bulb2:
2.3.1.1. The trade name or ▇▇▇▇ of the applicant;
2.3.1.2. The rated voltage. However, for filament light sources for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when if the maximum allowed bulb diameter of the filament light source type does not exceed 7.5 mm;
2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament light sources); this need not be indicated separately if it is part of the international designation of the relevant filament light source category;
2.3.1.5. A space of sufficient size to accommodate the approval ▇▇▇▇;
2.3.1.6. In the case of LED replacement light sources, the following symbol3: " .
2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Halogen filament light sources meeting the requirements of paragraph 3.3.47. below shall be marked with a "U".
2.3.4. LED replacement light sources shall be marked “LEDr”. This ▇▇▇▇ shall be placed after or below the designation of the relevant LED replacement light source category separated by a single character space or line space.
2.3.5. In the case of electrical/electronic controls not integrated with the LED replacement light source, the controls [used for the type approval] shall be marked with [type and trade ▇▇▇▇ identification and with the rated voltage and wattage, as indicated on the relevant lamp data sheet,] [as well as the category designation(s) and approval code(s) of the LED replacement light source(s) approved with these electrical/electronic controls].
Inscriptions. 2.3.1. Light sources submitted for approval shall bear:4
2.3.1.1. The trade name or mark of the applicant;
2.3.1.2. The rated voltage. However, for light sources for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. The designation of the relevant category. The wattage character "W" of this designation need not be marked if the maximum allowed bulb diameter of the light source type does not exceed 7.5 mm;
2.3.1.4. The rated wattage in the case of a filament light source, (in the sequence, high wattage/low wattage filament for dual-filament light sources); this need not be indicated separately if it is part of the designation of the relevant filament light source category;
2.3.1.5. The character "ͰE "5 in the case of a high-efficiency LED replacement light source; this mark shall be placed before the truncated circle according to paragraph 2.4.3.1., separated by a single character space.
2.3.1.6. A space of sufficient size to accommodate the approval mark;
2.3.1.7. In the case of a LED replacement light sources for which at least one of the conditions in paragraph 2.2.
2.2.2. applies, the following symbol:6 4 The luminous characteristics shall not be adversely affected.
Inscriptions. The titles of the Articles and sections of this Agreement shall be inserted only for reference and shall not be used in any way in the interpretation of this Agreement. 11.8.
Inscriptions. The headings in these general terms and conditions only serve to promote readability and do not form part of these terms and conditions.
Inscriptions. 2.3.1. LED light sources submitted for approval shall bear on the cap:
2.3.1.1. The trade name or mark of the applicant;
2.3.1.2. The rated voltage;
2.3.1.3. The designation of the relevant category;
2.3.1.4. A space of sufficient size to accommodate the approval mark.
2.3.1.5. In the case of LED substitute light sources, the following symbol1:
2.3.2. The space mentioned in paragraph 2.3.1.4. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.4. may be affixed, on the condition that they do not adversely affect the luminous characteristics.
Inscriptions. 2.3.1. LED light sources submitted for approval shall bear on the cap:
2.3.1.1. The trade name or ▇▇▇▇ of the applicant;
2.3.1.2. The rated voltage;
2.3.1.3. The designation of the relevant category;
2.3.1.4. A space of sufficient size to accommodate the approval ▇▇▇▇.
2.3.2. The space mentioned in paragraph 2.3.1.4. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.4. may be affixed, on the condition that they do not adversely affect the luminous characteristics.
Inscriptions on monuments shall not include religious symbols or ornamentation of a non-Jewish character or appearance.
Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb: 2/
2.3.1.1. the trade name or ▇▇▇▇ of the applicant;
2.3.1.2. the rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. the international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed