Installations Sample Clauses
The Installations clause defines the requirements and responsibilities related to the setup and placement of equipment, fixtures, or systems at a specified location. It typically outlines who is responsible for performing the installation, the standards or specifications that must be met, and any necessary approvals or inspections. For example, it may require the contractor to install machinery according to manufacturer guidelines and obtain sign-off from the client upon completion. This clause ensures that installations are completed properly and safely, reducing the risk of disputes or faulty work.
Installations. This test shall be conducted with either the complete REESS or with a related REESS subsystem(s) including the cells and their electrical connections. If the manufacturer chooses to test with related subsystem(s), the manufacturer shall demonstrate that the test result can reasonably represent the performance of the complete REESS with respect to its safety performance under the same conditions. If the electronic management unit for the REESS is not integrated in the casing enclosing the cells, then the electronic management unit may be omitted from installation on the Tested-Device if so requested by the manufacturer.
Installations. Any special carpentry, wiring, electrical or other work, gas, steam, water and drainage connection shall be installed at Exhibitor’s expense, and in accordance with the building and Management’s direction.
Installations. This test shall be conducted, under standard operating conditions, either with a complete vehicle or with the complete REESS. Ancillary systems that do not influence the test results may be omitted from the Tested-Device. The test may be performed with a modified Tested-Device provided these modifications shall not influence the test results.
Installations. The Landlord will keep in repair and in proper working order the installations in the Let Property for the supply of water, gas, electricity, sanitation, space heating and water heating (with the exception of those installed by the Tenant or which the Tenant is entitled to remove). ENERGY PERFORMANCE CERTIFICATE (EPC): A valid EPC (not more than 10 years old) must be given to the Tenant at or before the start date of the tenancy, unless the Tenant is renting a room with shared access to a kitchen, bathroom and living area.
Installations. Any installations of Electric Metering Equipment required pursuant to this Agreement shall be scheduled by the Seller; provided, however, that no installation which shall or could affect deliveries of Net Energy shall be made without the prior written consent of Buyer, which shall not be unreasonably withheld. Any installations of check meters by Buyer shall be scheduled by Buyer; provided, however that the installation shall not unreasonably interfere with the operation and maintenance of the Facility by the Seller.
Installations. No Owner shall cut, maim, alter, affix, interfere with, damage or in any other way affect or permit or suffer to be cut, maimed, altered, affixed, interfered with, damaged or in any other way affected any pipes, valves, ducts, lightning conductors, communal television and radio aerial system, fixtures or any other installation provided in the Building or any part of the Common Areas and Facilities.
Installations. This test shall be conducted either with a complete vehicle or with the complete REESS or with the REESS subsystem(s). If the manufacturer chooses to test with REESS subsystem(s), the Tested-Device shall be able to deliver the nominal voltage of the complete REESS and the manufacturer shall demonstrate that the test result can reasonably represent the performance of the complete REESS with respect to its safety performance under the same conditions. If the electronic management unit for the REESS is not integrated in the casing enclosing the cells, then the electronic management unit may be omitted from installation on the Tested-Device if so requested by the manufacturer. For a test with a complete vehicle, the manufacturer may provide information to connect a breakout harness to a location just outside the REESS that would permit applying a short circuit to the REESS.
Installations. 10.1. Merchant shall coordinate and agree to project-manage the installation and setup of its location(s). ▇▇▇▇▇▇▇▇ agrees that setup operations, configuration, installation, and training will take place 7 a.m. to 7 p.m. Pacific Time via telephone, Monday through Friday, excluding banking holidays. Modification to Merchant’s merchant information maintained by SHIFT4 that relate to any particular Credit Card Processor or MSP cannot be made on weekends due the unavailability of those entities.
Installations. 2.1. This test shall be conducted either with the complete REESS or with REESS subsystem(s) If the manufacturer chooses to test with REESS subsystem(s), the manufacturer shall demonstrate that the test result can reasonably represent the performance of the complete REESS with respect to its safety performance under the same conditions. If the electronic management unit for the REESS is not integrated in the casing enclosing the cells, then the electronic management unit may be omitted from installation on the Tested-Device if so requested by the manufacturer.
2.2. The Tested-Device shall be firmly secured to the platform of the vibration machine in such a manner as to ensure that the vibrations are directly transmitted to the Tested-Device. The Tested-Device should be mounted with its original mounting points, if those exist in the Tested-Device, as mounted in the vehicle.
Installations. This test shall be conducted either with the complete REESS or with related REESS subsystem(s) including the cells and their electrical connections. If the manufacturer chooses to test with related subsystem(s), the manufacturer shall demonstrate that the test result can reasonably represent the performance of the complete REESS with respect to its safety performance under the same conditions. If the electronic management unit for the REESS is not integrated in the casing enclosing the cells, then the electronic management unit may be omitted from installation on the tested-device if so requested by the manufacturer. Where the relevant REESS subsystems are distributed throughout the vehicle, the test may be conducted on each relevant of the REESS subsystem.