Meter Installation and Testing Sample Clauses

The Meter Installation and Testing clause outlines the requirements and procedures for installing and verifying the accuracy of utility meters, such as those measuring electricity, water, or gas usage. It typically specifies who is responsible for providing and installing the meter, the standards or methods to be used for testing its accuracy, and the process for addressing any discrepancies found during testing. This clause ensures that both parties have a clear understanding of how consumption will be measured and verified, thereby preventing disputes over usage and billing.
Meter Installation and Testing. Seller shall cause the installation, maintenance, operation and replacement (as needed) of a meter to be used as the Electric Revenue Meter and back-up meters, in accordance with the Transmission Provider’s metering protocols, at the Electrical Delivery Point to determine the amount of the Energy produced by the Units and delivered to the Electrical Delivery Point, [and the Gas Meter and back-up meters, in accordance with the requirements of the interconnecting pipeline, at the Gas Delivery Point, to determine the amount of Gas delivered to the Gas Delivery Point, in each case] at its sole cost and expense. To the extent necessary to isolate data related to each Unit, Seller shall cause the installation, maintenance, operation and replacement (as needed) of electrical [and/or Gas] submeters, at its sole cost and expense; provided that each such submeter shall be of revenue quality and sufficient for the purposes of providing the data contemplated by this Agreement. Each [Gas Meter and] Electric Revenue Meter shall be locked or sealed only by, and the lock or seal shall be broken only by, the interconnecting utility or Transmission Provider, as applicable. All of the submeters will be locked or sealed by both Parties, which locks or seals will only be broken by both Parties for inspection, testing or adjustment. The meters shall meet all specifications of the Transmission Provider [or interconnecting Gas pipeline, as applicable], and all meters and submeters shall be tested annually by Seller, who shall provide Buyer with not less than 14 days prior Notice of such tests. Testing procedures and standards for submeters shall be the same as for a comparable utility-owned meter. Buyer will have the right to have a representative present during such tests. [For facilities other than Gas-fired facilities, omit the bracketed language].
View SourceView Similar (11)
Meter Installation and Testing. Seller shall, at its sole expense, cause the installation, maintenance, operation and replacement (as needed) of a meter to be used as the Electric Revenue Meter and back-up meters, in accordance with the Transmission Provider’s metering protocols, at the Electrical Delivery Point to measure the Delivered Discharge Energy, the Charging Energy, and, as applicable, Integral Station Use. Each Electric Revenue Meter shall be locked or sealed only by, and the lock or seal shall be broken only by, the interconnecting utility or Transmission Provider, as applicable. The meters shall meet all specifications of the Transmission Provider, as applicable, and all meters and submeters shall be tested annually by Seller, who shall provide Buyer with not less than fourteen (14) days prior Notice of any tests, inspection, or adjustment of a meter or submeter. Testing procedures and standards for submeters will be the same as for a comparable utility-owned meter. Buyer will have the right to have a representative present during such tests, inspections, or adjustments. Whether or not Buyer elects to observe such tests, inspections or adjustments, Seller will provide Buyer with details of the results, including an as-found and as-left calibration certificate.
View Source
Meter Installation and Testing. Every consumer shall provide a suitable and accessible place where a meter can be installed, and the city shall install and maintain same. If the consumer desires to have the meter tested for accuracy, the same shall be done by the city, and a fee of $1 charged to the customer if the meter registers 98% or more accurate. If the meter registers less than 98% accurate, it shall be replaced, and repaired before installation on another service.
View Source

Related to Meter Installation and Testing

  • Installation, Maintenance, Testing and Repair Unless otherwise agreed in writing by the Parties, to the extent required by Applicable Law, Interconnection provided by a Party shall be equal in quality to that provided by such Party to itself, any subsidiary, affiliates or third party. If either Party is unable to fulfill its obligations under this Section 14.2, it shall notify the other Party of its inability to do so and will negotiate alternative intervals in good faith. The Parties agree that to the extent required by Applicable Law, the standards to be used by a Party for isolating and clearing any disconnections and/or other outages or troubles shall be at parity with standards used by such Party with respect to itself, any subsidiary, affiliate or third party.

  • Installation and Use You may install and use the Software only for the number of licenses acquired by you. In order to exercise your rights to the Software under this Agreement, you must activate your copy of the Software in the manner described during the launch sequence.

  • Inspection and Testing Each Constructing Entity shall cause inspection and testing of the Interconnection Facilities that it constructs in accordance with the provisions of this section. The Construction Parties acknowledge and agree that inspection and testing of facilities may be undertaken as facilities are completed and need not await completion of all of the facilities that a Constructing Entity is building.

  • Maintenance Repairs Utility Installations Trade Fixtures and Alterations (a) Subject to the provisions of Paragraphs 2.2 (Lessor’s warranty as to condition), 2.3 (Lessor’s warranty as to compliance with covenants, etc.), 7.2 (Lessor’s obligations to repair), 9 (damage and destruction), and 14 (condemnation), Lessee shall, at Lessee’s sole cost and expense and at all times, keep the Premises and every part thereof in good order, condition and repair, structural and non-structural (whether or not such portion of the Premises requiring repair, or the means of repairing the same, are reasonably or readily accessible to Lessee, and whether or not the need for such repairs occurs as a result of Lessee’s use, any prior use, the elements or the age of such portion of the Premises), including, without limiting the generality of the foregoing all equipment or facilities serving the Premises, such as plumbing, heating, air conditioning, ventilating, electrical, lighting facilities, boilers, fired or unfired pressure vessels, fire sprinkler and/or standpipe and hose or other automatic fire extinguishing system, including fire alarm and/or smoke detection systems and equipment, fire hydrants, fixtures, walls (interior and exterior), foundations, ceilings, roofs, floors, windows, doors, plate glass, skylights, landscaping, driveways, parking lots, fences, retaining walls, signs, sidewalks and parkways located in, on, about, or adjacent to the Premises. Lessee shall not cause or permit any Hazardous Substance to be spilled or released in, on, under or about the Premises (including through the plumbing or sanitary sewer system) and shall promptly, at Lessee’s expense, take all investigatory and/ore remedial action reasonably recommended, whether or not formally ordered or required, for the cleanup of any contamination of, and for the maintenance, security and/or monitoring of, the Premises, the elements surrounding same, or neighboring properties that was caused or materially contributed to by Lessee, or pertaining to or involving any Hazardous Substance and/or storage tank brought onto the premises by or for lessee or under its control. Lessee, in keeping the Premises in good order, condition and repair, shall exercise and perform good maintenance practices. Lessee’s obligations shall include restorations, replacements or renewals when necessary to keep the Promises and all improvements thereon or a part thereof in good order, condition and state of repair. If Lessee occupies the Premises for seven (7) years or more, lessor may require Lessee to repaint the exterior of the buildings on the Premises as reasonably required, but not more frequently than once every seven (7) years. (b) Lessee shall, at Lessee’s sole cost and expense, procure and maintain contracts, with copies to Lessor, in customary form and substance for, and with contractors specializing and experienced in, the inspection, maintenance and service of the following equipment and improvements, if any, located on the Premises: (i) heating, air conditioning and ventilation equipment, (ii) boiler, fired or unfired pressure vessels, (iii) fire sprinkler and/or standpipe and hose or other automatic fire extinguishing systems, including fire alarm and/or smoke detection. (iv) landscaping and irrigation systems, (v) roof covering and drain maintenance and (vi) asphalt and parking lot maintenance.

  • Installation and Maintenance Except for the bi‐directional and production metering equipment owned by the City, all equipment on Customer’s side of the delivery point, including the required disconnect device, shall be provided and maintained in satisfactory operating condition by Customer and shall remain the property and responsibility of the Customer. The City will bear no responsibility for the installation or maintenance of Customer’s equipment or for any damage to property as a result of any failure or malfunction thereof. The City shall not be liable, directly or indirectly for permitting or continuing to allow the interconnection of the Facility or for the acts or omissions of Customer or the failure or malfunction of any equipment of Customer that causes loss or injury, including death, to any party.