Metering Accuracy Clause Samples

Metering Accuracy. 1. The accuracy of the Primary Meters, ▇▇▇▇’▇ ▇▇▇▇ Meters and Gas Analysis Equipment is described in Table 1. Concerning Interconnection Point and Fuel Gas energy flow rate, it is expressed in relation to the maximum rate of gas flow that the meters may accommodate.
View SourceView Similar (4)
Metering Accuracy. If the Meters are registering but their accuracy is outside the limits established in ANSI C12.1, Buyer shall repair and recalibrate or replace the Meters and Buyer shall adjust payments to Supplier for the Delivered Amount for the lesser of the period in which the inaccuracy existed or ninety (90) days. If the period in which the inaccuracy existed cannot be determined, adjusted payments shall be made for a period equal to one-half of the elapsed time since the latest prior test and calibration of the Meters; however, the adjustment period shall not exceed ninety (90) days. If adjusted payments are required, Supplier shall render a statement describing the adjustments to Buyer within thirty (30) days of the date on which the inaccuracy was rectified. Additional payments to Supplier by Buyer shall be made within thirty (30) days of receipt of Supplier's statement. Any payments due Buyer pursuant to this Section shall accompany Supplier's statement.
View SourceView Similar (4)
Metering Accuracy. The tariff metering scheme shall have an overall accuracy of ± 0.2 % for watt-hour metering. In summary the Metering System reading accuracies are to be within the tolerances set out below: Net Energy Output (kWh) meters ± 0.2% Net Energy Output (kVARh) meters ± 0.5% Capacity (MW) meters ± 0.2% Instrument Transformers Calibration data shall be provided for each instrument transformer, which should result in a negligible overall error ± 0.2% Time Reference 3 seconds per week - maximum
View Source
Metering Accuracy. System metering accuracy, as compared to the actual process value, shall be determined from the value read at the principal readout device such as the recorder, totalizer. System requirements shall not preclude any requirements specified herein for individual devices. For systems where the primary measuring device, transmitter, and receiver are furnished under this section, the accuracy’s shall be within the following limits: a. Pressure: 1.0 percent of measured span. b. Level: 1.0 percent of measured span. c. Temperature: 1.0 percent of measured span. d. Position: 2.0 percent maximum travel.
View Source
Metering Accuracy. ‌ Accurate reporting of input power (power factor, input current, input current harmonics and voltage) and output power (output current and voltage) readings shall be reported via communication system at all rated voltage. The accuracy shall be maintained across the operating temperature range and between 200Vac and 305Vac. parameter Load Accuracy AC input power <10% ±25W 10-20% <± 5% 20-100% < ±3% AC input current <10% ±0.5A 10-20% < ±2% 20-100% < ±1% AC input current THD <10% ±10% 10-20% ±2% 20-100% ±1% Power factor <10% ±0.1 10-20% ±0.02 20-100% ±0.01 AC input voltage 0-100% ±1% output voltage 0-100% ±0.5% output current 0-100% ±1% output power <10% ±25W 10-20% <3% 20-100% <2%
View Source
Metering Accuracy. 1. The accuracy of the Flow Measurement Equipment, ▇▇▇▇’▇ ▇▇▇▇ Meters and Gas Analysis Equipment is described in Table 1. Concerning Interconnection Point and Fuel Gas energy flow rate, it is expressed in relation to the maximum rate of gas flow that the meters may accommodate. Flow Measurement Equipment Volume Flow Rate Nm³/hour 86,765 to 4,000,000 +/-0.96% Flow Measurement Equipment Energy Flow Rate MJ/hour 3,375,139 to 180,000,000 +/-1.0% ▇▇▇▇’▇ ▇▇▇▇ Gas Volume Flow Rate Sm³/hour 0 to 2,333,333 +/-5.0% ▇▇▇▇’▇ ▇▇▇▇ Gas Energy Flow Rate MJ/hour 0 to 104,066,666 +/-5.0% Offtake Pressure Flow Measurement Equipment ▇▇▇▇ 0 to 80 +/-0.16 Gross Calorific Value MJ/Nm³ MJ/Sm³ 36.9 to 47.5 35.0 to 45.0 +/-0.05 +/-0.05 ▇▇▇▇▇ Index MJ/Nm³ MJ/Sm³ 47.5 to 56.2 45.0 to 53.3 +/-0.06 +/-0.06 Offtake Temperature °C -10 to 45 +/-0.25 Hydrocarbon Dewpoint °C Water Dewpoint °C -50 to 15 +/-2.0 Oxygen ppm vol <5000 0 to 25 ppm range at 10 ppm, +/-2.0. 25 to 5000 ppm range at 2000 ppm, +/-50.0
View Source
Metering Accuracy. Metering accuracy shall be subject to the regulations of the Finnish Safety and Chemicals Agency or any other official body that holds jurisdiction over the matter according to current applicable legislation. A water meter shall be deemed to read correctly if the measurement error upon inspection is less than ±5% at a load that is approximately equivalent to the nominal flow, unless applicable regulations specify otherwise. If the consumption data of a remotely readable water meter received via the telecommunications network differs from the reading on the meter, the reading on the meter shall be considered correct when no fault can be found in the meter upon inspection.
View Source

Related to Metering Accuracy

  • Data Accuracy The Custodian has no responsibility for, or duty to review, verify or otherwise perform any investigation as to the completeness, accuracy or sufficiency of, any data or information provided by or on behalf of the Client, any persons authorized by the Client, any Third Party Agent, any Market Participant or any Authorized Data Sources, except to the extent the Custodian has agreed in writing to perform reconciliations, variance or tolerance checks or other specific forms of data review under this Agreement.

  • Preserve Accuracy of Representations and Warranties Each party hereto will refrain from taking any action which would render any of its representations and warranties contained in this Agreement untrue, inaccurate or misleading as of Closing and the Effective Time. Through Closing, each party will promptly notify the other parties of any lawsuit, claim, audit, investigation, administrative action or other proceeding asserted or commenced against such party that may involve or relate in any way to another party to this Agreement. Each party hereto will promptly notify the other parties of any facts or circumstances that come to its attention and that cause, or through the passage of time may cause, any of a party's representations, warranties or covenants to be untrue or misleading at any time from the date hereof through Closing.

  • Certification of Accuracy The following parties have reviewed the information above and certify, to the best of their knowledge, that the information they have provided is true and accurate.

  • Accuracy of the Company’s Representations and Warranties Each of the representations and warranties of the Company in this Agreement and the other Transaction Documents that are qualified by materiality or by reference to any Material Adverse Effect shall be true and correct in all respects, and all other representations and warranties shall be true and correct in all material respects, as of the date when made and as of the Closing Date as though made at that time, except for representations and warranties that are expressly made as of a particular date, which shall be true and correct in all respects as of such date.

  • Accuracy of Representations and Warranties; Performance of Covenants At the Closing Time, the representations and warranties contained herein or in certificates of any officer of the Company or any of its subsidiaries (including the Bank) delivered pursuant to the provisions hereof, shall be true and correct, when made, and at the Closing Time, and the Company shall have performed its covenants and other obligations hereunder.