Monitoring Components Clause Samples

Monitoring Components. The 2020 IM 15 monitoring activities include public health and baseline monitoring components.
View SourceView Similar (5)
Monitoring Components. ‌ Five secured manhole monitoring stations, with leak detection probes, are located along the transfer line from the EWs. Should a leak occur, an alarm signal is displayed at the main system control panel and the corresponding EW pump(s) will shut down automatically. Local control panels for system monitoring are located at each EW, the sand filter skid, and the air stripper skid. Each EW pump has a flowmeter/totalizer, pressure gauge, and HIGH and LOW pressure sensor that will initiate a shutdown of the pumps at pre-set pressure levels. Additionally, the PLC will shut down the pump(s) when manually prompted by the operator, when the EQ tank level is high, or when a leak is detected in the pipeline. After shutdown, the pump(s) are manually restarted at the main system control panel only after all alarm conditions have been cleared. The main system control panel is located inside the NWPGS facility and has a graphic display of the system, an operator interface unit, and the PLC. A TCE online analyzer is used to monitor effluent TCE concentrations and has a high-level alarm linked to the PLC.
View SourceView Similar (2)
Monitoring Components. A mechanical flow rate/totalizer is installed in each NEPCS TU for recording flow rates and total volume pumped. Trailer effluent concentrations are measured at CERCLA Outfall 001 and for the liquid effluent of each trailer per the requirements of Section 4.
View Source
Monitoring Components. The AIP 2009 Monitoring Plan includes the following two components. 3.1 Monitoring Component 1: Public health monitoring of Cyanobacteria and toxins
View Source
Monitoring Components. ‌ The monitoring module is responsible of implementing and centralizing the function- alities and algorithms to actually perform end-to-end measurements. It is build of three main components: The Passive Measurements Components (▇▇▇) ▇▇▇ implements the set of mea- surement functionalities needed to monitor exchanges between peers. This func- tion is basically passive as it relies on peers’ communications and never run active measurement probes to reduce as much as possible any overhead. The feasible passive measurements are explained in Chapters 2 and 3. Results of each measurement are then fed to the Monitoring Controller, which possibly elaborate them before pushing the result in the P-REP and N-Rep (via the Rep- Controller). ▇▇▇ is implemented in every peer, and it is optionally used by peers when sending chunks (i.e., the chunk trading logic can pass the chunk to the ▇▇▇). information. This function possibly runs a number of different measurement probes, either periodically or on request. For example, it may be invoked to esti- mate the end-to-end status between the local peer and a remote peer to which no chunks are being sent. Therefore, AcM may be also seen as a bootstrap function when limited knowledge of the peers and the network is stored in the P-REP and N-REP.
View Source

Related to Monitoring Components

  • Monitoring System In each case in which the Custodian has exercised delegated authority to place Assets with a Foreign Custodian, the Custodian shall establish a system, to re-assess or re-evaluate selected Foreign Custodians, at least annually in accordance with Rule 17f-5(c)(3).

  • Components Patheon will purchase and test all Components (with the exception of Client-Supplied Components) at Patheon’s expense and as required by the Specifications.

  • Monitoring Compliance Upon the request of the Lender, but without incurring any liability beyond the Guaranteed Obligations, from time to time, Guarantor shall promptly provide to the Lender such documents, certificates and other information as may be deemed reasonably necessary to enable the Lender to perform its functions under the Servicing Agreement as the same relates to the Guarantor.

  • Monitoring Services IDT staff shall, using methods that include face-to-face and other contacts with the member, monitor the services a member receives. This monitoring shall ensure that: a. The member receives the services and supports authorized, arranged for and coordinated by the IDT staff; b. The services and supports identified in the MCP as being provided by natural and community supports are being provided; and c. The quality of the services and supports received is adequate and still necessary to continue to meet the needs and preferences of the member and support the member’s outcomes identified in the MCP.

  • Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.