Push-On Joints Sample Clauses

Push-On Joints a. Where specified shall be the rubber ring compression, push-on type joint suitable for buried service. b. Unless otherwise indicated, joints shall have an allowable deflection of up to 5 degrees at specified pressures. c. Unless otherwise indicated, this joint is not permitted on fittings or specials. d. Joint assembly and field cut joints shall be made in strict conformance with AWWA C600 and e. Acceptable manufacturer: 1) American Cast Iron Pipe Company, Fastite Joint. 2) U.S. Pipe, Tyton Joint. 3)
Push-On Joints. Jointing shall be performed according to these specifications and the manufacturer's recommendations with special care used in cleaning gasket seat to prevent any dirt or sand from getting between the gasket and pipe. Lubricant to be used on the gasket shall be nontoxic and free from contamination. When a pipe length is cut, the outer edge of the cut shall be filed to a beveled edge to prevent injury to the gasket while joining.
Push-On Joints a. As specified in Section 15062, modified for restraint. b. Capable of being deflected after full assembly.

Related to Push-On Joints

  • Four on, Two off Schedule In an effort to maximize full-time employment opportunities, the local parties may agree to a “four on, two off” innovative schedule, subject to the following principles: (a) The introduction of such schedules and trial periods, if any, shall be determined by the local parties. Each Home must have the majority agreement of the full-time and part- time employees who vote on the issue to agree on a trial period of up to six months. Once the trial period is complete, each Home must have a minimum of 66⅔% agreement of the full-time and part-time employees who vote on the issue to continue with the new schedule on a permanent basis. (b) The implementation of such schedules shall be established only by mutual agreement of the Employer and the Union. (c) Notwithstanding the definition for full-time employee under Article 2.02, employees who participate in this schedule will normally be scheduled for thirty-five (35) hours per week on average and will be considered a full- time employee for all purposes of the collective agreement. i) Notwithstanding Article 16.01, for the purposes of bi-weekly overtime, the normal weekly full-time hours shall remain at seventy-five (75) hours per bi-weekly average over a six (6) week period. In each bi-weekly pay period the employee will be paid for all hours worked. At the end of the six (6) week period, entitlement for bi-weekly overtime will be calculated and paid. ii) Notwithstanding Article 16.01, for the purposes of daily overtime, the normal daily hours shall remain at seven and a half (7.5) hours per day. In each bi-weekly pay period the employee will be paid for all hours worked including daily overtime, if any. (e) For the purposes of vacation entitlement, the current collective agreement provisions shall apply using thirty-five (35) hours per week. (f) Each facility/unit must have eighty percent (80%) agreement of the full- time and part-time employees who work in the facility/unit. (g) The Four on, Two off schedule, may be discontinued by either party upon receipt of twelve (12) weeks’ notice to the other in writing of its desire to terminate. A meeting shall be held within two (2) weeks of receipt of such notice to discuss the reasons for the discontinuation. The Four on, Two off schedule, may be discontinued by the Union in any facility/unit when sixty percent (60%) of the employees in the facility/unit so indicate by secret ballot to the Union.

  • Specified Roads “Specified Roads” are roads, including related transportation facilities and appurtenances, shown on Sale Area Map and listed in A7. Purchaser shall construct Specified Roads used under this contract. Construction initiated by Purchaser on any such Specified Road shall be completed to an agreed terminus that meets Purchaser’s needs and prevents unnecessary impact on National Forest resources. Construction to such terminus shall be in full accordance with Plans and specifications and the Schedule of Items identified in A7 or specifications attached hereto, except for agreed adjustments needed to accommodate such terminus. The "Schedule of Items" is a list and description of construction items, quantities, units of measure, methods of measurement, unit price, and total amount. Forest Service shall revise the Schedule of Items to show the estimated cost for the portion constructed to the revised terminus as a separate segment.

  • Closing Date Balance Sheet (a) Within thirty (30) days after the Closing Date, Buyer shall prepare and deliver to Shareholders' Representative a draft Closing Date Balance Sheet, which shall be prepared (i) in accordance with GAAP applied in a manner consistent with the past practice of the Company, except as otherwise specifically required by the Net Worth Methodology and (ii) in a manner consistent with the December Balance Sheet. (b) If Shareholders' Representative has no objections to the draft Closing Date Balance Sheet, such draft shall constitute the Closing Date Balance Sheet. If Shareholders' Representative has any objections to the draft Closing Date Balance Sheet, it will deliver a detailed statement describing its objections to Buyer within thirty (30) days after receiving the draft Closing Date Balance Sheet. Shareholders' Representative and Buyer will use their commercially reasonable efforts to resolve any such objections. If Shareholders' Representative duly gives Buyer such notice of objection, and if Buyer and Shareholders' Representative fail to resolve the issues outstanding with respect to the Closing Date Balance Sheet and the calculation of the Closing Date Net Worth within thirty (30) days of Buyer's receipt of Shareholders' Representative's objection notice, Buyer and Shareholders' Representative shall submit the issues remaining in dispute to PricewaterhouseCoopers, certified public accountants (the "Independent Accountants"). If issues remaining in dispute are submitted to the Independent Accountants for resolution, (i) Buyer and Shareholders' Representative shall promptly furnish or cause to be furnished to the Independent Accountants such work papers and other documents and information relating to the disputed issues as the Independent Accountants may request and are available to that party or its agents and shall be afforded the opportunity to present to the Independent Accountants any material relating to the disputed issues and to discuss the issues with the Independent Accountants; (ii) the determination by the Independent Accountants, as set forth in a notice to be delivered to both Buyer and Shareholders' Representative within thirty (30) days of the submission to the Independent Accountants of the issues remaining in dispute, shall be final, binding and conclusive on the parties and shall be used in the calculation of the Closing Date Net Worth; and (iii) Buyer shall bear fifty percent (50%) of the fees and costs of the Independent Accountants for such determination and fifty percent (50%) of such fees and expenses shall be paid from the Escrow Fund. (c) Buyer will make the work papers used in preparing the draft Closing Date Balance Sheet and the Closing Date Balance Sheet available to Shareholders' Representative at reasonable times and upon reasonable notice at any time during the preparation by Buyer of the draft Closing Date Balance Sheet and the resolution of any objections with respect thereto.

  • _CheckoutDate_ _CheckoutTime_ Rental $_Rental_ Fees $_Fees_ Taxes $_AreaTax_ Total $_NetAmount_ Security Deposit $_RefundableSecurityDeposit_ Deposit $_DepositAmount_ (due _DepositDueDate_) Balance $_BalanceAmount_ (due _BalanceDueDate_)

  • No Exhibit E without unaltered DPA including Texas Addendum Any alterations are only allowed in Exhibit “H”. Any terms under Exhibit “H” do not apply to Exhibit “E” and render Exhibit “E” null and void.