Common use of SHOP DRAWINGS, PRODUCT DATA AND SAMPLES Clause in Contracts

SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. A. The Contractor shall furnish to the Designer all Samples of the materials to be used in the execution of the Work as required by the Contract Documents. The Contractor shall furnish to the Designer in a timely manner all coordination Drawings, shop details, Shop Drawings, and setting diagrams which may be necessary for acquiring and installing materials. These shall be reviewed as required by the Designer. Unless otherwise specified by the Awarding Authority, the Contractor shall provide a minimum of four (4) copies when submitting for final approval by the Designer, one of which shall be returned to the Contractor, one to the Resident Engineer, one to the Awarding Authority and one filed with the Designer. The inspection and approval by the Designer of Shop Drawings and setting diagrams shall be general and shall in no way relieve the Contractor from responsibility for proper fitting, coordinating, construction, and construction sequencing. The Contractor shall furnish to the Designer such information and vouchers relative to the Work, the materials therefor, and the persons employed thereon, as the Designer shall from time to time request. B. Shop Drawings, Product Data, Samples, and similar submittals are not Contract Documents. The purpose of their submission is to demonstrate for those portions of the Work for which submittals are required the way the Contractor proposes to conform to the information given and the design concept expressed in the Contract Documents. C. The Contractor shall review, approve, and submit to the Designer, Shop Drawings, Product Data, Samples and similar submittals required by the Contract Documents with reasonable promptness and in such sequence as to cause no delay in the Work or in the activities of the Awarding Authority or of separate contractors. Submittals made by the Contractor which are not required by the Contract Documents or which do not comply with the Contract Documents may be returned without action. The Contractor's attention is directed to the provisions of Section 4 of this Article V and to the Specifications. D. The Contractor shall prepare and keep current for the Designer's approval a schedule of submittals which is coordinated with the Progress Schedule and allows the Designer reasonable time to review submittals. E. The Contractor shall perform no portion of the Work requiring submittal and review of Shop Drawings, Product Data, Samples or similar submittals until the respective submittal has been approved by the Designer. Such Work shall be in accordance with approved submittals. F. By submitting Shop Drawings, Product Data, Samples and similar submittals, the Contractor represents that the Contractor has determined and verified materials, field measurements, and field construction criteria related thereto and has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. G. The Contractor shall not be relieved of responsibility for deviations from requirements of the Contract Documents by the Designer's approval of Shop Drawings, Product Data, Samples or similar submittals unless the Contractor has specifically informed the Designer in writing of such deviation at the time of submittal and the Awarding Authority has given explicit written approval to the specific deviation. The Contractor shall not be relieved of responsibility for errors or omissions in Shop Drawings, Product Data, Samples, or similar submittals by the Designer's or the Awarding Authority's actions. H. The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data, Samples or similar submittals, to revisions other than those requested by the Designer on previous submittals. I. Informational submittals upon which the Designer is not expected to take responsive action may be so identified in the Contract Documents. J. When professional certification of performance criteria of materials, systems or equipment is required by the Contract Documents, such certification must be stamped by a registered Massachusetts professional in the discipline required. The Designer shall be entitled to rely upon the accuracy and completeness of such calculations and certifications. K. Materials furnished or used or employed under the Contract must be equal in quality to the Samples furnished and be satisfactory to the Designer.

SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. A. The Contractor shall furnish to the Designer all Samples samples of the materials to be used in the execution of the Work as required by the Contract Documents. The Contractor shall furnish to the Designer in a timely manner all coordination Drawings, shop details, Shop Drawings, and setting diagrams which may be necessary for acquiring and installing materials. These shall be reviewed as required by the Designer. Unless otherwise specified by the Awarding Authority, the Contractor shall provide a A minimum of four (4) copies when submitting shall be submitted for final approval by the Designerapproval, one of which shall be returned to the Contractor, one to the Resident Engineer, one to the Awarding Authority and one filed with the Designer. The inspection and approval by the Designer of Shop Drawings and setting diagrams Drawings, etc. shall be general and shall in no way relieve the Contractor from responsibility for proper fitting, coordinating, construction, and construction sequencing. The Contractor shall furnish to the Designer such information and vouchers relative to the Work, the materials therefor, and the persons employed thereon, as the Designer shall from time to time request. B. Shop Drawings, Product Data, Samples, and similar submittals are not Contract Documents. The purpose of their submission is to demonstrate for those portions of the Work for which submittals are required the way the Contractor proposes to conform to the information given and the design concept expressed in the Contract Documents.the C. The Contractor shall review, approve, and submit to the Designer, Shop Drawings, Product Data, Samples and similar submittals required by the Contract Documents with reasonable promptness and in such sequence as to cause no delay in the Work or in the activities of the Awarding Authority or of separate contractors. Submittals made by the Contractor which are not required by the Contract Documents or which do not comply with the Contract Documents may be returned without action. The Contractor's attention is directed to the provisions of Section 4 of this Article V and to the Specifications. D. The Contractor shall prepare and keep current for the Designer's approval a schedule of submittals which is coordinated with the Progress Schedule and allows the Designer reasonable time to review submittals. E. The Contractor shall perform no portion of the Work requiring submittal and review of Shop Drawings, Product Data, Samples or similar submittals until the respective submittal has been approved by the Designer. Such Work shall be in accordance with approved Approved submittals. F. By submitting Shop Drawings, Product Data, Samples and similar submittals, the Contractor represents that the Contractor has determined and verified materials, field measurements, and field construction criteria related thereto and has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. G. The Contractor shall not be relieved of responsibility for deviations from requirements of the Contract Documents by the Designer's approval of Shop Drawings, Product Data, Samples or similar submittals unless the Contractor has specifically informed the Designer in writing of such deviation at the time of submittal and the Awarding Authority has given explicit written approval to the specific deviation. The Contractor shall not be relieved of responsibility for errors or omissions in Shop Drawings, Product Data, Samples, or similar submittals by the Designer's or the Awarding Authority's actions. H. The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data, Samples or similar submittals, to revisions other than those requested by the Designer on previous submittals. I. Informational submittals upon which the Designer is not expected to take responsive action may be so identified in the Contract Documents. J. When professional certification of performance criteria of materials, systems or equipment is required by the Contract Documents, such certification must be stamped by a registered Massachusetts professional in the discipline required. The Designer shall be entitled to rely upon the accuracy and completeness of such calculations and certifications. K. Materials furnished or used or employed under the Contract must be equal in quality to the Samples samples furnished and be satisfactory to the Designer.

SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. A. The 3.16.1 Shop Drawings are drawings, diagrams, schedules and other data specifically prepared for the Work by the Contractor shall furnish or a Subcontractor, sub- subcontractor, manufacturer, supplier or distributor to the Designer all Samples illustrate some portion of the materials to be used in the execution of Work. 3.16.2 Product Data are illustrations, standard schedules, performance charts, instructions, 3.16.3 Samples are physical samples which illustrate materials, equipment or workmanship and establish standards by which the Work as required by the Contract Documents. The Contractor shall furnish to the Designer in a timely manner all coordination Drawings, shop details, Shop Drawings, and setting diagrams which may will be necessary for acquiring and installing materials. These shall be reviewed as required by the Designer. Unless otherwise specified by the Awarding Authority, the Contractor shall provide a minimum of four (4) copies when submitting for final approval by the Designer, one of which shall be returned to the Contractor, one to the Resident Engineer, one to the Awarding Authority and one filed with the Designer. The inspection and approval by the Designer of Shop Drawings and setting diagrams shall be general and shall in no way relieve the Contractor from responsibility for proper fitting, coordinating, construction, and construction sequencing. The Contractor shall furnish to the Designer such information and vouchers relative to the Work, the materials therefor, and the persons employed thereon, as the Designer shall from time to time requestjudged. B. 3.16.4 Shop Drawings, Product Data, Samples, Samples and similar submittals (collectively referred to as “Submittals”) are not Contract Documents. The purpose of their submission submittal is to demonstrate for those portions of the Work for which submittals are required the way the Contractor proposes to conform to the information given and the design concept expressed in the Contract Documents. C. 3.16.5 The Contractor shall review, approve, schedule submittal of Shop Drawings and submit Product Data to the DesignerEngineer so that no delays will result in delivery of materials and equipment, advising the Engineer of priority for checking of Shop Drawings, Drawings and Product Data, but a minimum of two weeks shall be provided for this purpose. All Shop Drawings and Product Data shall be submitted prior to the Contractor’s third partial payment request. After the second payment has been made, no further payments will be made until all required Shop Drawings and Product Data have been submitted. If Shop Drawings and Product Data are not approved by the fourth progress payment request, the Owner may withhold further payments. 3.16.6 The Contractor, at its own expense, shall submit Samples and similar submittals required by the Contract Documents with reasonable promptness and in such sequence as to cause no delay in the Work or in the activities of separate contractors and no later than twenty (20) days before materials are required to be ordered for scheduled delivery to the Awarding Authority Work site. Samples shall be labeled to designate material or products represented, grade, place of separate contractorsorigin, name of producer, name of Contractor and the name and number of the Owner’s Project. Submittals made by Quantities of Samples shall be twice the Contractor which are not number required by for testing so that Engineer can return one set of the Contract Documents or which do not comply with the Contract Documents Samples. Materials delivered before receipt of Engineer’s approval may be returned without actionrejected by Engineer and in such event, Contractor shall immediately remove all such materials from the Work site. The Contractor's attention is When requested by Engineer or Owner’s Representative, samples of finished masonry and field applied paints and finishes shall be located as directed to and shall include sample panels built at the provisions site of Section 4 of this Article V and to the Specificationsapproximately twenty (20) square feet each. D. The Contractor shall prepare and keep current for the Designer's approval a schedule of submittals which is coordinated with the Progress Schedule and allows the Designer reasonable time to review submittals. E. 3.16.7 The Contractor shall perform no portion of the Work requiring submittal and review of Shop Drawings, Product Data, Samples or similar submittals until the respective submittal has been approved by the DesignerEngineer. Such Work shall be in accordance with approved submittals. F. 3.16.8 By approving and submitting Shop Drawings, Product Data, Samples and similar submittals, the Contractor represents such Submittals strictly comply with the requirements of the Contract Documents and that the Contractor has determined and verified materials, field measurements, measurements and field construction criteria related thereto thereto, that materials are fit for their intended use and has checked that the fabrication, shipping, handling, storage, assembly and coordinated installation of all materials, systems and equipment are in accordance with best practices in the information contained within such submittals industry and are in strict compliance with the any applicable requirements of the Work and of the Contract Documents. Contractor shall also coordinate each Submittal with other Submittals. G. 3.16.9 Contractor shall be responsible for the correctness and accuracy of the dimensions, measurements and other information contained in the Submittals. 3.16.10 Each Submittal will bear a stamp or specific indication that the Submittal complies with the Contract Documents and Contractor has satisfied its obligations under the Contract Documents with respect to Contractor’s review and approval of that Submittal. Each Submittal shall bear the signature of the representative of Contractor who approved the Submittal, together with the Contractor’s name, Owner’s name, number of the Project, and the item name and specification section number. 3.16.11 The Contractor shall not be relieved of responsibility for deviations from requirements of the Contract Documents by the Designer's Engineer’s approval of Shop Drawings, Product Data, Samples or similar submittals unless the Contractor has specifically informed the Designer in writing of such deviation at the time of submittal and the Awarding Authority has given explicit written approval to the specific deviationsubmittals. The Contractor shall not be relieved of responsibility for errors or omissions in Shop Drawings, Product Data, Samples, Samples or similar submittals by the Designer's or Engineer’s approval thereof. Specifically, but not by way of limitation, Contractor acknowledges that Engineer’s approval of Shop Drawings shall not relieve Contractor for responsibility for errors and omissions in the Awarding Authority's actionsShop Drawings since Contractor is responsible for the correctness of dimensions, details and the design of adequate connections and details contained in the Shop Drawings. H. 3.16.12 The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data, Samples or similar submittals, to revisions other than those requested by the Designer Engineer on previous submittalsSubmittals. I. Informational submittals upon 3.16.13 The Contractor represents and warrants that all Shop Drawings shall be prepared by persons and entities possessing expertise and experience in the trade for which the Designer Shop Drawing is not expected to take responsive action may be so identified in the Contract Documents. J. When professional certification of performance criteria of materialsprepared and, systems or equipment is if required by the Contract DocumentsEngineer or applicable Laws, such certification must be stamped by a registered Massachusetts professional in the discipline required. The Designer shall be entitled to rely upon the accuracy and completeness of such calculations and certificationslicensed engineer or other design professional. K. Materials furnished or used or employed under the Contract must be equal in quality to the Samples furnished and be satisfactory to the Designer.

SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. A. The Contractor shall furnish to the Designer all Samples of the materials to be used in the execution of the Work as required by the Contract Documents. The Contractor shall furnish to the Designer in a timely manner all coordination Drawings, shop details, Shop Drawings, and setting diagrams which may be necessary for acquiring and installing materials. These shall be reviewed as required by the Designer. Unless otherwise specified by the Awarding Authority, the Contractor shall provide a minimum of four (4) copies when submitting for final approval by the Designer, one of which shall be returned to the Contractor, one to the Resident Engineer, one to the Awarding Authority and one filed with the Designer. The inspection and approval by the Designer of Shop Drawings and setting diagrams shall be general and shall in no way relieve the Contractor from responsibility for proper fitting, coordinating, construction, and construction sequencing. The Contractor shall furnish to the Designer such information and vouchers relative to the Work, the materials therefor, and the persons employed thereon, as the Designer shall from time to time request.in B. Shop Drawings, Product Data, Samples, and similar submittals are not Contract Documents. The purpose of their submission is to demonstrate for those portions of the Work for which submittals are required the way the Contractor proposes to conform to the information given and the design concept expressed in the Contract Documents. C. The Contractor shall review, approve, and submit to the Designer, Shop Drawings, Product Data, Samples and similar submittals required by the Contract Documents with reasonable promptness and in such sequence as to cause no delay in the Work or in the activities of the Awarding Authority or of separate contractors. Submittals made by the Contractor which are not required by the Contract Documents or which do not comply with the Contract Documents may be returned without action. The Contractor's attention is directed to the provisions of Section 4 of this Article V and to the Specifications. D. The Contractor shall prepare and keep current for the Designer's approval a schedule of submittals which is coordinated with the Progress Schedule and allows the Designer reasonable time to review submittals. E. The Contractor shall perform no portion of the Work requiring submittal and review of Shop Drawings, Product Data, Samples or similar submittals until the respective submittal has been approved by the Designer. Such Work shall be in accordance with approved submittals. F. By submitting Shop Drawings, Product Data, Samples and similar submittals, the Contractor represents that the Contractor has determined and verified materials, field measurements, and field construction criteria related thereto and has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. G. The Contractor shall not be relieved of responsibility for deviations from requirements of the Contract Documents by the Designer's approval of Shop Drawings, Product Data, Samples or similar submittals unless the Contractor has specifically informed the Designer in writing of such deviation at the time of submittal and the Awarding Authority has given explicit written approval to the specific deviation. The Contractor shall not be relieved of responsibility for errors or omissions in Shop Drawings, Product Data, Samples, or similar submittals by the Designer's or the Awarding Authority's actions. H. The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data, Samples or similar submittals, to revisions other than those requested by the Designer on previous submittals. I. Informational submittals upon which the Designer is not expected to take responsive action may be so identified in the Contract Documents. J. When professional certification of performance criteria of materials, systems or equipment is required by the Contract Documents, such certification must be stamped by a registered Massachusetts professional in the discipline required. The Designer shall be entitled to rely upon the accuracy and completeness of such calculations and certifications. K. Materials furnished or used or employed under the Contract must be equal in quality to the Samples furnished and be satisfactory to the Designer.

SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. ‌ A. The Contractor shall furnish to the Designer Project Engineer all Samples samples of the materials to be used in the execution of the Work as required by the Contract Documents. The Contractor shall furnish to the Designer DCR in a timely manner all coordination Drawings, shop details, Shop Drawings, and setting diagrams which may be necessary for acquiring and installing materials. These shall be reviewed as required by the DesignerDCR. Unless otherwise specified by the Awarding Authority, the Contractor shall provide a A minimum of four six (46) copies when submitting shall be submitted for final approval by the Designerapproval, one of which shall be returned to the Contractor, one given to the Resident Engineer, one to and four maintained by the Awarding Authority and one filed with the DesignerDCR. The inspection and approval by the Designer DCR of Shop Drawings and setting diagrams Drawings, etc. shall be general and shall in no way relieve the Contractor from responsibility for proper fitting, coordinating, construction, and construction sequencing. The Contractor shall furnish to the Designer DCR such information and vouchers relative to the Work, the materials therefortherefore, and the persons employed thereon, as the Designer DCR shall from time to time-to-time request. B. Shop Drawings, Product Data, Samples, and similar submittals are not Contract Documents. The purpose of their submission is to demonstrate for those portions of the Work for which submittals are required the way the Contractor proposes to conform to the information given and the design concept expressed in the Contract Documents. C. The Contractor shall review, approve, and submit to the DesignerDCR, Shop Drawings, Product Data, Samples Samples, and similar submittals required by the Contract Documents with reasonable promptness and in such sequence as to cause no delay in the Work or in the activities of the Awarding Authority DCR or of separate contractors. Submittals made by the Contractor which are not required by the Contract Documents Documents, or which do not comply with the Contract Documents may be returned without action. The Contractor's attention is directed to the provisions of Section 4 of this Article V and to the Specifications. D. The Contractor shall prepare and keep current for the DesignerDCR's approval a schedule of submittals which is coordinated with the Progress Schedule and allows the Designer DCR reasonable time to review submittals. E. The Contractor shall perform no portion of the Work requiring submittal and review of Shop Drawings, Product Data, Samples Samples, or similar submittals until the respective submittal has been approved by the DesignerDCR. Such Work shall be in accordance with approved Approved submittals. F. By submitting Shop Drawings, Product Data, Samples and similar submittals, the Contractor represents that the Contractor has determined and verified materials, field measurements, and field construction criteria related thereto and has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. G. The Contractor shall not be relieved of responsibility for deviations from requirements of the Contract Documents by the Designer's approval of Shop Drawings, Product Data, Samples or similar submittals unless the Contractor has specifically informed the Designer in writing of such deviation at the time of submittal and the Awarding Authority has given explicit written approval to the specific deviation. The Contractor shall not be relieved of responsibility for errors or omissions in Shop Drawings, Product Data, Samples, or similar submittals by the Designer's or the Awarding Authority's actions. H. The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data, Samples or similar submittals, to revisions other than those requested by the Designer on previous submittals. I. Informational submittals upon which the Designer is not expected to take responsive action may be so identified in the Contract Documents. J. When professional certification of performance criteria of materials, systems or equipment is required by the Contract Documents, such certification must be stamped by a registered Massachusetts professional in the discipline required. The Designer shall be entitled to rely upon the accuracy and completeness of such calculations and certifications. K. Materials furnished or used or employed under the Contract must be equal in quality to the Samples furnished and be satisfactory to the Designer.

SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. A. The Contractor shall furnish to the Designer all Samples of the materials to be used in the execution of the Work as required by the Contract Documents. The Contractor shall furnish to the Designer in a timely manner all coordination Drawings, shop details, Shop Drawings, and setting diagrams which may be necessary for acquiring and installing materials. These shall be reviewed as required by the Designer. Unless otherwise specified by the Awarding Authority, the Contractor shall provide a minimum of four (4) copies when submitting for final approval by the Designer, one of which shall be returned to the Contractor, one to the Resident Engineer, one to the Awarding Authority and one filed with the Designer. The inspection and approval by the Designer of Shop Drawings and setting diagrams shall be general and shall in no way relieve the Contractor from responsibility for proper fitting, coordinating, construction, and construction sequencing. The Contractor shall furnish to the Designer such information and vouchers relative to the Work, the materials therefor, and the persons employed thereon, as the Designer shall from time to time request. B. 3.18.1 Shop Drawings, Product Data, Samples, and similar submittals Samples are not Contract Documentspart of the Contract. The purpose of their submission DESIGN-BUILD CONTRACTOR submittals is to demonstrate demonstrate, for those portions of the Work for which submittals are required required, the way the Contractor DESIGN-BUILD CONTRACTOR proposes to conform to the information given and the design concept expressed in the Contract DocumentsContract. DESIGN-BUILD CONTRACTOR shall submit required submittals and requests for information (RFIs) into the HAS project management system. Access to the project management system portal and required training will be coordinated through the Director. C. The Contractor 3.18.2 DESIGN-BUILD CONTRACTOR shall review, approve, and submit to Director for review the Designer, Shop Drawings, Product Data, Samples and similar submittals Samples, which are required by the Contract Documents Documents. Review by Director is subject to limitations of Paragraph 4.1.4. DESIGN-BUILD CONTRACTOR shall transmit the submittals to the Director with reasonable promptness and in such sequence a sequence, so as to cause no delay in the Work or in the activities of the Awarding Authority City or of separate contractorsContractors. Submittals made DESIGN-BUILD CONTRACTOR shall transmit submittals in time to allow a minimum of fourteen (14) days for Director’s review prior to date DESIGN-BUILD CONTRACTOR needs reviewed submittals returned. This time may be shortened for a particular job requirement if approved by Director in advance of submittal. 3.18.3 DESIGN-BUILD CONTRACTOR shall certify that the Contractor which are not required by content of submittals conforms to the Contract Documents or which do not comply without exception by affixing DESIGN-BUILD CONTRACTOR’s approval stamp and signature. By certifying and submitting Shop Drawings, Product Data, and Samples, DESIGN-BUILD CONTRACTOR represents, and DESIGN-BUILD CONTRACTOR’s stamp of approval shall state, that DESIGN-BUILD CONTRACTOR has determined and verified materials, quantities, field measurements, and field construction criteria related to the submittal, and has checked and coordinated information contained within the submittals with requirements of the Contract Documents may be returned without action. The Contractor's attention is directed to the provisions of Section 4 of this Article V and to the Specifications. D. The Contractor shall prepare and keep current for the Designer's approval a schedule of submittals which is coordinated compatibility with the Progress Schedule and allows the Designer reasonable time to review other submittals. E. The Contractor shall 3.18.4 DESIGN-BUILD CONTRACTOR may not perform no portion of the Work any work requiring submittal and review of Shop Drawings, Product Data, or Samples or similar submittals until the respective submittal has been approved returned with appropriate review decision by the DesignerDirector. Such DESIGN-BUILD CONTRACTOR shall perform Work shall be in accordance with approved submittalsthe review. F. By submitting 3.18.5 If DESIGN-BUILD CONTRACTOR performs any Work requiring submittals prior to review and acceptance of the submittals by Director, such Work is at DESIGN-BUILD CONTRACTOR’s risk and the City is not obligated to accept Work if the submittals are later found to be unacceptable. 3.18.6 If, in the opinion of Director, the submittals are incomplete, or demonstrate an inadequate understanding of the Work or lack of review by the DESIGN-BUILD CONTRACTOR, then submittals may be returned to the DESIGN-BUILD CONTRACTOR for correction and resubmittal. 3.18.7 DESIGN-BUILD CONTRACTOR shall direct specific attention in writing and on the resubmitted Shop Drawings, Product Data, or Samples and similar to any additional proposed revisions, other than those revisions requested by Director on previous submittals, the Contractor represents that the Contractor has determined and verified materials, field measurements, and field construction criteria related thereto and has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. G. The Contractor shall 3.18.8 DESIGN-BUILD CONTRACTOR is not be relieved of responsibility for deviations from requirements of the Contract Documents by the Designer's Director’s review or approval of Shop Drawings, Product Data, or Samples or similar submittals unless the Contractor DESIGN-BUILD CONTRACTOR has specifically informed the Designer Director in writing of such the deviation at the time of submittal the submittal, and the Awarding Authority Director has given explicit written approval to of the specific deviation. The Contractor shall not be relieved of responsibility for errors or omissions in Shop Drawings, Product Data, Samples, or similar submittals by the Designer's or the Awarding Authority's actions. H. The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data, Samples or similar submittals, to revisions other than those requested by the Designer on previous submittals. I. Informational submittals upon which the Designer is not expected to take responsive action may be so identified in the Contract Documents. J. 3.18.9 When professional certification of performance criteria of materials, systems or equipment Products is required by the Contract DocumentsContract, such certification must be stamped by a registered Massachusetts professional in the discipline required. The Designer shall be entitled to City may rely upon the accuracy and completeness of such the calculations and certifications. K. Materials furnished 3.18.10 For Product colors or used or employed under textures to be selected by the City, DESIGN-BUILD CONTRACTOR shall submit all samples together to allow preparation of a complete selection schedule. 3.18.11 DESIGN-BUILD CONTRACTOR shall submit informational submittals, on which Director is not expected to take responsive action, as required by the Contract. 3.18.12 Submittals made by DESIGN-BUILD CONTRACTOR which are not required by the Contract must may be equal in quality returned to the Samples furnished and be satisfactory to the DesignerDESIGN-BUILD CONTRACTOR without action.

SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. A. The Contractor shall furnish to the Designer all Samples samples of the materials to be used in the execution of the Work as required by the Contract Documents. The Contractor shall furnish to the Designer in a timely manner all coordination Drawings, shop details, Shop Drawings, and setting diagrams which may be necessary for acquiring and installing materials. These shall be reviewed as required by the Designer. Unless otherwise specified by the Awarding Authority, the Contractor shall provide a A minimum of four (4) copies when submitting shall be submitted for final approval by the Designerapproval, one of which shall be returned to the Contractor, one to the Resident Engineer, one to the Awarding Authority and one filed with the Designer. The inspection and approval by the Designer of Shop Drawings and setting diagrams Drawings, etc. shall be general and shall in no way relieve the Contractor from responsibility for proper fitting, coordinating, construction, and construction sequencing. The Contractor shall furnish to the Designer such information and vouchers relative to the Work, the materials therefor, and the persons employed thereon, as the Designer shall from time to time request. B. Shop Drawings, Product Data, Samples, and similar submittals are not Contract Documents. The purpose of their submission is to demonstrate for those portions of the Work for which submittals are required the way the Contractor proposes to conform to the information given and the design concept expressed in the Contract Documents. C. The Contractor shall review, approve, and submit to the Designer, Shop Drawings, Product Data, Samples and similar submittals required by the Contract Documents with reasonable promptness and in such sequence as to cause no delay in the Work or in the activities of the Awarding Authority or of separate contractors. Submittals made by the Contractor which are not required by the Contract Documents or which do not comply with the Contract Documents may be returned without action. The Contractor's attention is directed to the provisions of Section 4 of this Article V and to the Specifications. D. The Contractor shall prepare and keep current for the Designer's approval a schedule of submittals which is coordinated with the Progress Schedule and allows the Designer reasonable time to review submittals. E. The Contractor shall perform no portion of the Work requiring submittal and review of Shop Drawings, Product Data, Samples or similar submittals until the respective submittal has been approved by the Designer. Such Work shall be in accordance with approved Approved submittals. F. By submitting Shop Drawings, Product Data, Samples and similar submittals, the Contractor represents that the Contractor has determined and verified materials, field measurements, and field construction criteria related thereto and has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. G. The Contractor shall not be relieved of responsibility for deviations from requirements of the Contract Documents by the Designer's approval of Shop Drawings, Product Data, Samples or similar submittals unless the Contractor has specifically informed the Designer in writing of such deviation at the time of submittal and the Awarding Authority has given explicit written approval to the specific deviation. The Contractor shall not be relieved of responsibility for errors or omissions in Shop Drawings, Product Data, Samples, or similar submittals by the Designer's or the Awarding Authority's actions. H. The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data, Samples or similar submittals, to revisions other than those requested by the Designer on previous submittals. I. Informational submittals upon which the Designer is not expected to take responsive action may be so identified in the Contract Documents. J. When professional certification of performance criteria of materials, systems or equipment is required by the Contract Documents, such certification must be stamped by a registered Massachusetts professional in the discipline required. The Designer shall be entitled to rely upon the accuracy and completeness of such calculations and certifications. K. Materials furnished or used or employed under the Contract must be equal in quality to the Samples samples furnished and be satisfactory to the Designer.