Surface Quality Clause Samples

Surface Quality. A surface quality to a mean roughness depth of Rz 0,25 (DIN EN ISO 4287) or AA 1 (ASME B46.1) must be achieved on both sealing surfaces through lapping. In the case of O-rings and plastics sealing (see chapter 8 and 9), different surface qualities may be as shown in the illustrations. These sealing surfaces may be achieved through smooth turning. Work is to be carried out according to Figure 1 to Figure 3 and Table 1 to Table 2. <.. image(Ein Bild, das Entwurf, Diagramm, Reihe, Zeichnung enthält. Automatisch generierte Beschreibung) removed ..> <.. image(Ein Bild, das Diagramm, Entwurf, Zeichnung, Reihe enthält. Automatisch generierte Beschreibung) removed ..> Figure 1. Disc
View SourceView Similar (2)
Surface Quality. Sweet potatoes should be of the same variety. The overall condition should be flawless and without mud or other dirt particles. There should be no low-quality sweet potatoes that are deformed, cracking, beaten by buds, or putrid.
View Source
Surface Quality. A surface quality to a mean roughness depth of Rz 0,25 (DIN EN ISO 4287) or AA 1 (ASME B46.1) must be achieved on both sealing surfaces through lapping. In the case of plastic and soft sealing, different surface qualities may be as shown in the figures. These sealing surfaces may be achieved alternatively through smooth turning.
View Source
Surface Quality. Scratch, contamination. Die with scratches visible to the eye, covering two pixels or more, a non-removable contamination is rejected if it covers more than three pixels with no two adjacent. Any die with these defects is rejected.
View Source
Surface Quality. Spread the HMA without tearing the surface. Strike a finish that is smooth, free of segregation, true to cross section, uniform in density and texture and free from surface irregularities. If the pavement does not comply with all of these requirements, plant production and paving will be suspended until the deficiency is corrected. The Engineer will check segregation and uniformity of density using methods outlined in Section 5.8.3, Segregation Check Using the Nuclear Density Gauge, Part V. For shoulders with a plan width of less than or equal to 3 feet, and placed at the same time as the traveled way, do not take nuclear density readings on the shoulder nor within 1 foot of the shoulder unless the pavement section is uniform across the entire roadway. The acceptable criteria for density uniformity are in TABLE 602-7. All 4.4 lbs./cu. ft. 2.2 lbs./cu. ft. Whenever the results from 2 consecutive density profiles fail to comply with both of the requirements listed in TABLE 602-7, plant production and paving will be suspended. Follow the procedures listed in the Profile Evaluation Subsection of Section 5.8.3, Segregation Check Using the Nuclear Density Gauge, Part V until production may be resumed. Joint density testing and the associated requirements listed below do not apply for HMA lift thicknesses less than or equal to 1 inch. Evaluate the longitudinal joint density using methods outlined in Section 5.8.4 Joint Density Evaluation Using the Nuclear Density Gauge, Part V. Although it is the Contractor’s responsibility to perform the joint density evaluation, the Engineer may make as many independent joint density verifications as deemed necessary at the random sample locations. The Engineer’s results will be used for acceptance for joint density, whenever available. The acceptable criteria for joint density are in TABLE 602-8. If the results of 2 consecutive density profiles fail to comply with TABLE 602-8, the plant production and paving operations will be suspended. Follow the procedures listed in the Joint Evaluation Subsection of Section 5.8.4 Joint Density Evaluation Using the Nuclear Density Gauge, Part V, until production may be resumed.
View Source
Surface Quality 
View Source

Related to Surface Quality

  • Image Quality You are responsible for the image quality of any Image that you transmit. If an Image that we receive from you or for deposit to your Account is not of sufficient quality to satisfy our image quality standards as we may establish them from time to time, we may reject the Image without prior notice to you. Each Image must include the front and back of the Item and the following information must be clearly readable: amount, payee name, drawer signature, date, check number, account number, routing and transit number, MICR (Magnetic Ink Character Recognition) line, and any endorsement or other information written on the check.

  • Service Quality The Transfer Agent shall maintain a quality control process designed to provide a consistent level of quality and timeliness for its call center, correspondence services and transaction processing.

  • Use; Quality Control a. Neither party may alter the other party’s trademarks from the form provided and must comply with removal requests as to specific uses of its trademarks or logos. b. Each party agrees to use, and to cause its Permitted Sublicensees to use, the other party’s trademarks only in good faith and in a dignified manner consistent with such party’s use of the trademarks. Upon written notice to the breaching party, the breaching party has 30 days of the date of the written notice to cure the breach or the license will be terminated.

  • Data Quality 4.1 Each party ensures that the shared Personal Data is accurate. 4.2 Parties will notify each other with undue delay if they become aware of inaccuracies in shared Personal Data.

  • Quality Assurance/Quality Control Contractor shall establish and maintain a quality assurance/quality control program which shall include procedures for continuous control of all construction and comprehensive inspection and testing of all items of Work, including any Work performed by Subcontractors, so as to ensure complete conformance to the Contract with respect to materials, workmanship, construction, finish, functional performance, and identification. The program established by Contractor shall comply with any quality assurance/quality control requirements incorporated in the Contract.