ACCESS TO WORK RULES Sample Clauses

The "Access to Work Rules" clause establishes the requirement for parties, typically contractors or employees, to comply with specific workplace policies and procedures set by the site owner or employer. This clause ensures that anyone accessing the worksite is informed of and abides by rules related to safety, security, conduct, and operational protocols. For example, it may require adherence to safety briefings, use of protective equipment, or following site-specific entry and exit procedures. Its core function is to maintain a safe, orderly, and compliant work environment by making sure all personnel are aware of and follow established site rules.
ACCESS TO WORK RULES. A copy of all current policies, procedure manuals, personnel releases, work rules, regulations, this Agreement, and any other documents concerning an employee’s rights, obligations, conduct, standards and performance requirements shall be made reasonably available upon the employee’s request.
View SourceView Similar (6)
ACCESS TO WORK RULES of all current policies, procedure manuals, personnel releases, work rules, 4 regulations, this Agreement, and any other documents concerning an employee’s rights, 5 obligations, conduct, standards and performance requirements shall be made 6 reasonably available upon the employee’s request.
View SourceView Similar (2)
ACCESS TO WORK RULES. The Employer agrees that, to the extent any work rules have been or will become reduced to writing, every employee shall have access to them for the duration of this Agreement. Should any work rules conflict with law or with the specific provisions of this Agreement, such rules shall be invalid to the extent of such conflict.
View Source
ACCESS TO WORK RULES of all current policies, procedure manuals, personnel releases, work rules, 35 regulations, this Agreement, and any other documents concerning an employee’s rights, 36 obligations, conduct, standards and performance requirements shall be made 37 reasonably available upon the employee’s request. 38
View Source

Related to ACCESS TO WORK RULES

  • Access to Work District representatives shall at all times have access to the Work, wherever it is, in preparation or in progress. Contractor shall provide safe and proper facilities for such access.

  • Access to Work Locations Reasonable access to employee work locations shall be granted officers of the Association and their officially designated representatives for the purpose of processing grievances or contacting members of the Association concerning business within the scope of representation. Such officers or representatives shall not enter any work location without the consent of the City Manager. Access shall be restricted so as not to interfere with the normal operations of the department or with established safety or security requirements. Solicitation of membership and activities concerned with the internal management of the Association, such as collecting dues, holding membership meetings, campaigning for office, conducting elections and distributing literature, shall not be conducted during working hours.

  • WORK RULES The State may change or adopt work rules during the term of this Agreement but such changed or adopted work rules shall not be inconsistent with the terms and provisions of this Agreement. Whenever such work rules are to be changed or adopted, they shall be posted on bulletin boards in the appropriate organizational units for seven (7) days before they are to become effective. Simultaneously with such posting a copy of same shall be forwarded to MSEA-SEIU. Upon request by MSEA-SEIU the State will meet and consult with MSEA-SEIU on the proposed changed or new rules.

  • Access to NID 2.7.3.1 NewPhone may access the customer’s premises wiring by any of the following means and NewPhone shall not disturb the existing form of electrical protection and shall maintain the physical integrity of the NID: 2.7.3.1.1 BellSouth shall allow NewPhone to connect its Loops directly to BellSouth’s multi-line residential NID enclosures that have additional space and are not used by BellSouth or any other telecommunications carriers to provide service to the premises; 2.7.3.1.2 Where an adequate length of the customer’s premises wiring is present and environmental conditions permit, either Party may remove the customer premises wiring from the other Party’s NID and connect such wiring to that Party’s own NID; 2.7.3.1.3 Either Party may enter the subscriber access chamber or dual chamber NID enclosures for the purpose of extending a cross-connect or spliced jumper wire from the customer premises wiring through a suitable “punch-out” hole of such NID enclosures; or 2.7.3.1.4 NewPhone may request BellSouth to make other rearrangements to the customer premises wiring terminations or terminal enclosure on a time and materials cost basis. 2.7.3.2 In no case shall either Party remove or disconnect the other Party’s loop facilities from either Party’s NIDs, enclosures, or protectors unless the applicable Commission has expressly permitted the same and the disconnecting Party provides prior notice to the other Party. In such cases, it shall be the responsibility of the Party disconnecting loop facilities to leave undisturbed the existing form of electrical protection and to maintain the physical integrity of the NID. It will be NewPhone’s responsibility to ensure there is no safety hazard, and NewPhone will hold BellSouth harmless for any liability associated with the removal of the BellSouth Loop from the BellSouth NID. Furthermore, it shall be the responsibility of the disconnecting Party, once the other Party’s loop has been disconnected from the NID, to reconnect the disconnected loop to a nationally recognized testing laboratory listed station protector, which has been grounded as per Article 800 of the National Electrical Code. If no spare station protector exists in the NID, the disconnected loop must be appropriately cleared, capped and stored. 2.7.3.3 NewPhone shall not remove or disconnect ground wires from BellSouth’s NIDs, enclosures, or protectors. 2.7.3.4 NewPhone shall not remove or disconnect NID modules, protectors, or terminals from BellSouth’s NID enclosures. 2.7.3.5 Due to the wide variety of NID enclosures and outside plant environments, BellSouth will work with NewPhone to develop specific procedures to establish the most effective means of implementing this section if the procedures set forth herein do not apply to the NID in question.

  • CONTRACT WORK HOURS AND SAFETY STANDARDS As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all Customer Purchase Orders in excess of ,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.