Design Speed Clause Samples

POPULAR SAMPLE Copied 1 times
Design Speed. The design speed shall be the ruling design speed specified for the applicable terrain type in the Schedule D, except in the locations where lower design speed is adopted in the plan and profile drawings.
View Source
Design Speed. A. Design all Roadways in accordance with the following maximum vehicular design speeds and Roadway types: Roadway Design Speed Roadway Type 1. ▇▇▇ ▇▇▇▇▇▇ ▇▇ km/h Collector 2. ▇▇ ▇▇▇▇▇▇ ▇▇ km/h Arterial 3. Muttart Service ▇▇▇▇ ▇▇ ▇▇/▇ Collector 4. ▇▇▇▇▇▇▇ ▇▇▇▇/▇▇ ▇▇▇▇▇▇ ▇▇ km/h Arterial 5. ▇▇ ▇▇▇▇▇▇ ▇▇ km/h Collector 6. ▇▇ ▇▇▇▇▇▇ ▇▇ km/h Arterial 7. 83 Street (90 Ave to 82Ave) 60 km/h Arterial 8. 83 Street (82 Ave to Argyll) 60 km/h Arterial 9. ▇▇ (▇▇▇▇▇) Avenue 60 km/h Arterial 10. ▇▇▇▇▇▇ ▇▇▇▇ ▇▇ km/h Arterial 11. ▇▇▇▇▇▇ ▇▇▇▇/▇▇▇▇▇▇ ▇▇▇▇ 60 km/h Collector 12. ▇▇ ▇▇▇▇▇▇ ▇▇ km/h Arterial ▇▇. ▇▇ ▇▇▇▇▇▇ ▇▇ km/h Arterial 14. ▇▇ ▇▇▇▇▇▇ ▇▇ km/h Collector
View Source
Design Speed a. The Design-Builder must meet the Maximum Design Speed for each section of the alignment up to 80 km/h and include all relevant calculations with the applicable Final Design submission. b. For each section of the alignment, the Design-Builder must include all relevant calculations with the applicable first Interim Design submission, second Interim Design submission, and Final Design submission for Maximum Operating Speed and Maximum Design Speed. c. Yard Track must have a Maximum Design Speed of 10 km/h.
View Source

Related to Design Speed

  • Design Services The Engineer shall perform services during the schematic design phase, the design development phase, the contract documents phase, and the bidding period as hereinafter specified.

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at a P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.

  • Configuration Management The Contractor shall maintain a configuration management program, which shall provide for the administrative and functional systems necessary for configuration identification, control, status accounting and reporting, to ensure configuration identity with the UCEU and associated cables produced by the Contractor. The Contractor shall maintain a Contractor approved Configuration Management Plan that complies with ANSI/EIA-649 2011. Notwithstanding ANSI/EIA-649 2011, the Contractor’s configuration management program shall comply with the VLS Configuration Management Plans, TL130-AD-PLN-010-VLS, and shall comply with the following:

  • Installation Services The Bitstream 2a Service includes a Standard Install as set out below (in each case to the extent that the relevant provisioning works are not already complete for the relevant Service Order).1

  • Installation When installation is required, the Contractor shall be responsible for placing and installing the Commodities or parts in the required locations at no additional charge. All materials used in the installation shall be of good quality and shall be free of defects that would diminish the appearance of the Commodity or render it structurally or operationally unsound. Installation includes the furnishing of any equipment, tools, rigging, labor, and materials required to install or replace the Commodities or parts in the proper location. Contractor shall protect the site from damage and shall repair damages or injury caused during installation by Contractor or its employees or agents. If any alteration, dismantling, excavation, etc., is required to achieve installation, the Contractor shall promptly restore the structure or site to its original condition. Contractor shall perform installation work so as to cause the least inconvenience and interference with Customers and with proper consideration of others on site. Upon completion of the installation, the location and surrounding area of work shall be left clean and in a neat and unobstructed condition, with everything in satisfactory repair and order.