Front Clause Samples

Front. Motor vehicles - the horizontal plane tangential to the upper edge of the apparent surface in the direction of the reference axis of the device shall not be lower than the horizontal plane tangential to the upper edge of the transparent zone of the wind-screen. Trailers and semi-trailers - at the maximum height compatible with the requirements relating to the width, design and operational requirements of the vehicle and to the symmetry of the lamps.

Front. End Construction Contract Documents—Those Construction Contract Documents whose primary purpose is to establish legal and contractual terms and conditions, typically including the Owner-Contractor agreement, bonds, general conditions, and supplementary conditions. The term excludes the Drawings and Specifications, and any Construction Contract Documents delivered or issued after the effective date of the Construction Contract.

Front. The fronts shall have a center facing 3" in width extending from neckline to bottom of shirt provided by a turn-under of material. The right front shall also have a lined box pleat 1-1/2" wide finished, running full length of the shirt and shall be topstitched 1/4" from both edges. The center front shall contain six vertical buttonholes placed 3/4" from edge, first at neck, second 21/2" down, balance 3-1/2" apart. Back: There is to be yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of poplin. Pockets: To have two breast pockets with mitered corners to finish 5" wide and 5-1/2" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/4" box stitching top and bottom to prevent spreading. Flaps: To have two scalloped flaps to finish 5-1/4" in length, 2-3/8" in width at center, and 2-1/8" in width at sides. Flaps to be secured to front of shirt with two rows of stitching approximately 1/4" above top of pocket. The left flap to have a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a matching button and a buttonhole sewn on the flap. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on inside of the shirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To have two small (horizontal) buttonholes, 1-1/4" apart with the bottom buttonhole 1-1/2" above top of left flap.

Front. Rear view; 1

Front. Microbiol. 8, 1901 (2017).

Front. Right; 1.

Front. The left front shall have a top center placket 1-1/2" wide with two rows of stitching 7/8” apart. The shirt will have 7 buttons and buttonholes on the front; spacing between each will be 3-¾" except the spacing between the neck button and the first button on the front, which will be approximately 3-1/4". Top center placket to have woven interlining of #250 Dacron. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16" raised stitch. Safety stitch joining unacceptable. Forest Green shoulder straps with set in gold cordedge. Shoulder straps to be two- piece pointed, topstitched along the edge to secure the cordedge and to be set on yoke with leading topstitch conforming with front joining seam. Shoulder straps to be interlined with #250 Dacron. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross-stitched approximately 2" from sleeve seam. Shoulder strap to have functional buttonhole to align with the sewn eyelet on the shoulder for metal button. Two-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 (two) buttonhole eyelets 1 1/8” from top of pocket flap, spaced 1” apart and centered on sling.

Front. End Fee may also consist of Switching Fee where subscriptions include cash identified as having been invested in any Fund in the past. ^ 1. Charged on amounts switched from any Fund.

Front. Quarter pocket style with L-shape measure 1-5/8” from the top waistband to 1-1/4” at the bottom at the side seam. Pockets constructed of one piece of the specified pocketing material finish approximately 7” wide at the bottom of pocket opening, and 12-1/2” long from where the pocket is sewn into the waistband. Pockets will be over-edge stitched, turned and top-stitched for security and clean-finishing. There is a shell facing, on palm side of pocket, from the side seam along waistband that measures 4-1/4” wide and taper to the bottom of pocket opening. Another shell facing placed on the inside of the pocket, away from the body, measuring 1-3/4” wide. There shall be a horizontal bar tack across the top of the pocket opening, on outer layer of waistband, and a vertical bar tack at the bottom of the pocket opening centered on the side seam for reinforcement.