HANDLING AND STORING Sample Clauses

The HANDLING AND STORING clause sets out the requirements and procedures for the proper management, movement, and storage of goods or materials under a contract. It typically details how items should be handled to prevent damage, specifies storage conditions such as temperature or security, and may assign responsibility for loss or deterioration during storage. This clause ensures that goods are preserved in optimal condition, reducing the risk of disputes over damage or loss and clarifying each party’s obligations regarding the care of materials.
HANDLING AND STORING. Load, transport, unload and store geosynthetics so geosynthetics are kept clean and free of damage. Label, ship and store geosynthetics in accordance with Section 7 of AASHTO M 288. Geosynthetics with defects, flaws, deterioration or damage will be rejected. Do not unwrap geosynthetics until just before installation. Do not leave geosynthetics exposed for more than 7 days before covering except for geosynthetics for temporary wall faces and erosion control. Provide Type 1, Type 2 or Type 4 material certifications in accordance with Article 106-3 for geosynthetics. Define “minimum average roll value” (▇▇▇▇) in accordance with ASTM D4439. Provide certifications with ▇▇▇▇ for geosynthetic properties as required. Test geosynthetics using laboratories accredited by the Geosynthetic Accreditation Institute (GAI) to perform the required test methods. Sample geosynthetics in accordance with ASTM D4354. When required, sew geotextiles together in accordance with Article X1.1.4 of AASHTO M 288. Provide sewn seams with seam strengths meeting the required strengths for the geotextile type and class specified. Provide geotextile types and classes in accordance with the contract. Geotextiles will be identified by the product name printed directly on the geotextile. When geotextiles are not marked with a product name or marked with only a manufacturing plant identification code, geotextiles will be identified by product labels attached to the geotextile wrapping. When identification is based on labels instead of markings, unwrap geotextiles just before use in the presence of the Engineer to confirm that the product labels on both ends of the outside of the geotextile outer wrapping match the labels affixed to both ends of the inside of the geotextile roll core. Partial geotextile rolls without the product name printed on the geotextile or product labels affixed to the geotextile roll core may not be used. Use woven or nonwoven geotextiles with properties that meet Table 1056-1. Define “machine direction” (MD) and “cross-machine direction” (CD) in accordance with ASTM D4439. Type 1 Type 2 Type 3A Type 4 Type 5B Elongation (MD & CD) ≥ 50% ≥ 50% ≤ 25% < 50% < 50% ASTM D4632 Grab Strength (MD & CD) Table 1D, Class 3 Table 1D, Class 1 100 lbC Table 1D, Class 3 – ASTM D4632 Tear Strength (MD & CD) – ASTM D4533 Puncture Strength – ASTM D6241 Ultimate Tensile Strength (MD & CD) – – – – 2,400 lb/ftC (unless required otherwise in the contract) ASTM D4595 Permittivity Table 2D, 15% ...
View SourceView Similar (14)

Related to HANDLING AND STORING

  • Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.

  • Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until they have received proper training and instruction. (b) The Employer shall provide sufficient and adequate training and/or orientation to any employee working in a new or unfamiliar work area or position.

  • Packaging and Shipping All shipping containers shall be packed and packaged to: (i) ensure safe arrival to final destination; (ii) secure the lowest transportation costs;(iii) comply with requirements of common carriers; (iv) meet Buyer's written instructions; and (v) meet the requirements of all applicable laws, ordinances, rules and regulations.

  • Transportation The School District will provide for such student transportation as may be required to and from the College as required under State law, and for any off-site academic course assignments which require the Student to travel to satisfy course objectives that could include, without limitation, museum visits or job-site internships, or approved School and College field trips or extra-curricular activities, each pursuant to applicable School District rules and procedures.

  • Dewatering (a) Where the whole of a site is so affected by surface water following a period of rain that all productive work is suspended by agreement of the Parties, then dewatering shall proceed as above with Employees so engaged being paid at penalty rates as is the case for safety rectification work. This work is typically performed by Employees engaged within CW1, CW2 or CW3 classifications. When other Employees are undertaking productive work in an area or areas not so affected then dewatering will only attract single time rates. (b) Where a part of a site is affected by surface water following a period of rain, thus rendering some areas unsafe for productive work, consistent with the Employer’s obligations under the OH&S Act, appropriate Employees shall assist in the tidying up of their own work site or area if it is so affected. Where required, appropriate Employees will be provided with the appropriate PPE. Such work to be paid at single time rates. Productive work will continue in areas not so affected. (c) To avoid any confusion any ‘dewatering’ time which prevents an Employee from being engaged in their normal productive work is not included in any calculation for the purposes of determining whether an Employee is entitled to go home due to wet weather (refer clauses 32.4 and 32.5)