Injection Characteristics Sample Clauses

The "Injection Characteristics" clause defines the specific properties and requirements for substances or materials that are to be injected within the scope of an agreement or technical process. This clause typically outlines parameters such as composition, pressure, temperature, and volume, ensuring that the injected material meets agreed-upon standards for safety and performance. By clearly specifying these characteristics, the clause helps prevent disputes over quality or compatibility, ensuring operational consistency and reducing the risk of equipment damage or process failure.
Injection Characteristics. The maximally usable injection rate is subject to the following characteristic restriction: • The customer shall be entitled to use up to a working gas account balance of WGABI1 the contracted total of injection rate (IR100%) up to 100 %. • From a working gas account balance of WGABI1 up to a working gas account balance of WGABI2 the customer shall be entitled to use an injection rate up to IRred1. • From a working gas account balance of WGABI2 up to a working gas account balance of WGABI3 the customer shall be entitled to use an injection rate up to IRred2. • From a working gas account balance of WGABI3 up to a working gas account balance of WGAB100 % the customer shall be entitled to use an injection rate up to IRred3. The following characteristic parameters result from the firm capacities of working gas volume and injection rate contracted by the customer: Service Period 6:00 a.m. – 6:00 a.m. IR100 % MWh/h IRred,1 MWh/h IRred,2 MWh/h IRred,3 MWh/h 01/04/2024 – 01/04/2025 […] […] […] […] Service Period WGABI1 WGABI2 WGABI3 WGAB100 %
View SourceView Similar (17)
Injection Characteristics. The maximally usable injection rate according to number 1.1 above is useable irrespective of a characteristic.
View SourceView Similar (7)
Injection Characteristics. The maximally usable injection rate is subject to the following characteristic restriction: • The customer shall be entitled to use up to a working gas account balance of WGABI the contracted total of injection rate (IR100%) up to 100 %. • Above the working gas account balance of WGABI the maximally usable injection rate shall be reduced linearly, but shall not fall short of the maximally usable injection rate of IRred.
View SourceView Similar (4)
Injection Characteristics. The injection characteristic of the storage facility ▇▇▇▇▇▇▇▇▇ is defined as follows: The maximally usable injection rate is subject to the following characteristic restriction: • Starting from an empty storage contract (working gas account 0) the maximally usable injection rate increases linearly from the IRred1 up to the overall contracted injection rate IR100%. • From a working gas account balance of WGABI1 up to a working gas account balance of WGABI2 the customer shall be entitled to use the overall contracted injection rate IRred100% up to 100 %. • From a working gas account balance of WGABI2 the maximally usable injection rate shall be reduced linearly, but shall not fall short of the maximally usable injection rate does not fall below IRred2. • From a working gas account balance of WGABI3 up to a working gas account balance of WGAB100 % the customer shall be entitled to use an injection rate up to IRred2.
View SourceView Similar (3)
Injection Characteristics. The chart below shows the injection characteristic of the contract that is schematically shown and described hereafter. The parameters IR100%, IRred, WGABI, WGABInt and WGAB100% used in this schematic chart and explained in the characteristic description are specified for the firm injection characteristic in the table under number 2.2. and for the overall injection char- acteristic in the table under number 2.3. The maximally usable injection rate is therefore subject to the characteristic restriction as described below:  The customer shall be entitled to use up to a working gas account balance of WGABI the totally contracted injection rate (IR100%) up to 100%.  From a working gas account balance of WGABI up to a working gas account balance of WGABInt the customer shall be entitled to use an injection rate up to IRred.  From a working gas account balance of WGABInt up to a working gas account balance of WGAB100% the customer shall be entitled to use an injection rate up to IRred but on an interruptible basis only, i.e. depending on VGS’s ability and capability.
View SourceView Similar (2)
Injection Characteristics. The maximally usable injection rate is subject to the following characteristic restriction: • The customer shall be entitled to use up to a working gas account balance of WGABI the contracted total of injection rate (IR100%) up to 100 %. • From a working gas account balance of WGABI up to a working gas account balance of 95 % of the totally contracted working gas volume (WGABint) the customer shall be en- titled to use an injection rate up to IRred. • From a working gas account balance of WGABint up to a working gas account balance of WGAB100 % customer shall be entitled to use an injection rate up to IRred but on an in- terruptible basis only, i.e. depending on VGS’s ability and capability. The following characteristic parameters result from the firm capacities of working gas volume and injection rate contracted by the customer: Service Period IR100 % IRred WGABI WGABInt WGAB100 %
View SourceView Similar (2)
Injection Characteristics. The maximally usable injection rate is subject to the following characteristic restriction:  The customer shall be entitled to use up to a working gas account balance of WGABI the contracted total of injection rate (IR100%) up to 100%.  From a working gas account balance of WGABI up to a working gas account balance of WGAB100% the customer shall be entitled to use an injection rate up to IRred. The following characteristic parameters apply to the firm capacities of working gas vol- ume and injection rate contracted by the customer: Period 6:00 a.m. – 6:00 a.m. IR100 % MWh/h IRred MWh/h WGABI GWh WGAB100 % GWh […] – […] […] […] […] […]
View Source

Related to Injection Characteristics

  • Characteristics The Contracts have the following characteristics: (i) all the Contracts are secured by Motorcycles; (ii) no Contract has a remaining maturity of more than 84 months; and (iii) the final scheduled payment on the Contract with the latest maturity is due no later than September 6, 2031. Approximately 74.40% of the Pool Balance as of the Cutoff Date is attributable to loans for purchases of new Motorcycles and approximately 25.60% is attributable to loans for purchases of used Motorcycles. No Contract was originated after the Cutoff Date. No Contract has a Contract Rate less than 0.010%.

  • ODUF Physical File Characteristics 6.2.1 ODUF will be distributed to TWTC via Secure File Transfer Protocol (FTP). The ODUF feed will be a variable block format. The data on the ODUF feed will be in a non-compacted EMI format (175 byte format plus modules). It will be created on a daily basis Monday through Friday except holidays. Details such as dataset name and delivery schedule will be addressed during negotiations of the distribution medium. There will be a maximum of one dataset per workday per OCN. If AT&T determines the Secure FTP Mailbox is nearing capacity levels, AT&T may move the customer to CONNECT: Direct file delivery. 6.2.2 If the customer is moved, CONNECT: Direct data circuits (private line or dial-up) will be required between AT&T and TWTC for the purpose of data transmission. Where a dedicated line is required, TWTC will be responsible for ordering the circuit, overseeing its installation and coordinating the installation with AT&T. TWTC will also be responsible for any charges associated with this line. Equipment required on the AT&T end to attach the line to the mainframe computer and to transmit messages successfully on an ongoing basis will be negotiated on an individual case basis. Any costs incurred for such equipment will be TWTC's responsibility. Where a dial-up facility is required, dial circuits will be installed in the AT&T data center by AT&T and the associated charges assessed to TWTC. Additionally, all message toll charges associated with the use of the dial circuit by TWTC will be the responsibility of TWTC. Associated equipment on the AT&T end, including a modem, will be negotiated on an individual case basis between the Parties. All equipment, including modems and software, that is required on TWTC end for the purpose of data transmission will be the responsibility of TWTC. 6.2.3 If TWTC utilizes FTP for data file transmission, purchase of the FTP software will be the responsibility of TWTC.

  • Mortgage Loan Characteristics The characteristics of the related Mortgage Loan Package are as set forth on the description of the pool characteristics for the applicable Mortgage Loan Package delivered pursuant to Section 11 on the related Closing Date in the form attached as Exhibit B to each related Assignment and Conveyance Agreement;

  • Physical File Characteristics 6.2.1 The Optional Daily Usage File will be distributed to CLEC-1 via an agreed medium with CONNECT:Direct being the preferred transport method. The Daily Usage Feed will be a variable block format (2476) with an LRECL of 2472. The data on the Daily Usage Feed will be in a non-compacted EMI format (175 byte format plus modules). It will be created on a daily basis (Monday through Friday except holidays). Details such as dataset name and delivery schedule will be addressed during negotiations of the distribution medium. There will be a maximum of one dataset per workday per OCN. 6.2.2 Data circuits (private line or dial-up) may be required between BellSouth and CLEC-1 for the purpose of data transmission. Where a dedicated line is required, CLEC-1 will be responsible for ordering the circuit, overseeing its installation and coordinating the installation with BellSouth. CLEC-1 will also be responsible for any charges associated with this line. Equipment required on the BellSouth end to attach the line to the mainframe computer and to transmit successfully ongoing will be negotiated on a case by case basis. Where a dial-up facility is required, dial circuits will be installed in the BellSouth data center by BellSouth and the associated charges assessed to CLEC-1. Additionally, all message toll charges associated with the use of the dial circuit by CLEC-1 will be the responsibility of CLEC-1. Associated equipment on the BellSouth end, including a modem, will be negotiated on a case by case basis between the parties. All equipment, including modems and software, that is required on CLEC-1 end for the purpose of data transmission will be the responsibility of CLEC-1.

  • Characteristics of Receivables Each Receivable (A) shall have been originated in the United States by a Dealer for the retail sale of the related Financed Vehicle in the ordinary course of such Dealer’s business, shall have been fully and properly executed by the parties thereto, shall have been purchased by the Seller from such Dealer under an existing agreement with the Seller, shall have been validly assigned by such Dealer to the Seller in accordance with its terms and, to the best knowledge of the Seller, shall have been sold by a Dealer without fraud or misrepresentation, (B) shall have created or shall create a valid, subsisting and enforceable first priority security interest in favor of the Seller in the related Financed Vehicle, (C) shall contain customary and enforceable provisions such that the rights and remedies of the holder thereof shall be adequate for realization against the collateral of the benefits of the security, (D) shall provide for level Monthly Payments (provided that the first or last payment in the life of the Receivable may be minimally different from the level payment) that fully amortize the Amount Financed over its original term and shall provide for a finance charge or shall yield interest at its APR, (E) shall provide for, in the event that such Receivable is prepaid, a prepayment that fully pays the Principal Balance and includes accrued but unpaid interest at least through the date of prepayment in an amount calculated by using an interest rate at least equal to its APR, (F) shall have an Obligor that is not a federal, state or local governmental entity and (G) is a retail installment contract.