Inspection and Quality Control Tests Clause Samples

Inspection and Quality Control Tests. 7.1 Inspection and Quality Control tests before evaluation, prior to shipment of Goods and at the time of final acceptance are as follows: (i) Inspection of Goods as per quality control formats including functional testing, burn-in tests and mains fluctuation test at full load, facilities etc., as per the standards may be done at factory site of the Supplier before award of the Purchase Contract, by the Bank / Bank’s Consultants; Provided that the Bank may, at its sole discretion, waive inspection of goods having regard to the value of the order and/or the nature of the goods and/or any other such basis as may be decided at the sole discretion of the Bank meriting waiver of such inspection of goods. (ii) The inspection of the Goods is to check whether the Goods are in conformity with the technical specifications mentioned in the Invitation for Quotation or the Quotation submitted by the Supplier. The Supplier will dispatch the goods to the ultimate consignee after internal inspection/testing along with the Supplier’s inspection report, manufacturer’s warranty certificate. The Bank / Bank’s Consultants may also carry out pre-dispatch inspection. In such a case, the entire cost of such inspection, including the board, lodging, travelling, incidental expenses of the Bank’s representatives and/or Consultants, shall totally be borne by the Supplier, for the complete duration of the inspection. Successful conduct and conclusion of pre-dispatch inspection shall be the sole responsibility of the Supplier; (iii) Also, the Bank will test the equipment after completion of the installation and commissioning at the site of the installation (for site preparation, the Supplier should furnish all details to the Bank sufficiently in advance so as to get the works completed before receipt of the equipment). Complete hardware and software should be supplied, installed and commissioned properly by the Supplier prior to commencement of performance tests; (iv) The acceptance test will be conducted by the Bank / Bank’s Consultants or any other person nominated by the Bank, at its option. The acceptance will involve trouble-free operation for a period to be decided by the Bank, but not exceeding seven consecutive days. There shall not be any additional charges for carrying out acceptance tests. No malfunction, partial or complete failure of any part of hardware or excessive heating of motors attached to printers, drivers etc. or bugs in the software should occur. All the software...
View Source

Related to Inspection and Quality Control Tests

  • Existence and Qualification; Power; Compliance With Laws Borrower is a corporation duly formed, validly existing and in good standing under the Laws of the State of California. Borrower is duly qualified or registered to transact business and is in good standing in the State of California, and each other jurisdiction in which the conduct of its business or the ownership or leasing of its Properties makes such qualification or registration necessary, except where the failure so to qualify or register and to be in good standing could not reasonably be expected to have a Material Adverse Effect. Borrower has all requisite power and authority to conduct its business, to own and lease its Properties and to execute and deliver each Loan Document to which it is a Party and to perform its Obligations. The chief executive offices of Borrower are located in San Dimas, California. All outstanding capital stock of Borrower is duly authorized, validly issued, fully paid and non-assessable, and no holder thereof has any enforceable right of rescission under any applicable state or federal securities or other Laws. Borrower is in compliance with all Laws and other legal requirements applicable to its business, has obtained all authorizations, consents, approvals, orders, licenses and permits from, and has accomplished all filings, registrations and qualifications with, or obtained exemptions from any of the foregoing from, any Governmental Agency that are necessary for the transaction of its business, except where the failure so to comply with Laws and other legal requirements applicable to its business, obtain authorizations, etc., file, register, qualify or obtain exemptions could not reasonably be expected to have a Material Adverse Effect.

  • Minimum Condition and Warranty Requirements for TIPS Sales All goods quoted or sold through a TIPS Sale shall be new unless clearly stated otherwise in writing. All new goods and services shall include the applicable manufacturers minimum standard warranty unless otherwise agreed to in the Supplemental Agreement.

  • STANDARDS AND QUALITY The Supplier shall at all times during the Contract Period ensure that the Services are delivered in accordance with: the Digital Service Design Manual (and the Supplier shall comply with the processes and procedures set out therein); the Standards; the KPIs; the Methodology; the applicable SOW; and all other applicable provisions of this Contract.

  • SMHS Governance, Safety and Quality Requirements 4.1 Participates in the maintenance of a safe work environment. 4.2 Participates in an annual performance development review. 4.3 Supports the delivery of safe patient care and the consumers’ experience including participation in continuous quality improvement activities in accordance with the requirements of the National Safety and Quality Health Service Standards and other recognised health standards. 4.4 Completes mandatory training (including safety and quality training) as relevant to role. 4.5 Performs duties in accordance with Government, WA Health, South Metropolitan Health Service and Departmental / Program specific policies and procedures. 4.6 Abides by the WA Health Code of Conduct, Occupational Safety and Health legislation, the Disability Services Act and the Equal Opportunity Act.

  • EMHS Governance, Safety and Quality Requirements 4.1 Participates in the maintenance of a safe work environment. 4.2 Actively participates in the Peak Performance program. 4.3 Supports the delivery of safe patient care and the consumers’ experience including participation in continuous quality improvement activities in accordance with the requirements of the National Safety and Quality Health Service Standards and other recognised health standards. 4.4 Completes mandatory training (including safety and quality training) as relevant to role. 4.5 Performs duties in accordance with the EMHS Vision and Values, WA Health Code of Conduct, Occupational Safety and Health legislation, the Disability Services Act and the Equal Opportunity Act and Government, WA Health, EMHS and Departmental / Program specific policies and procedures.