Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth or ComSouth-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network: 11.4.1 A-link interface from ComSouth local or tandem switching systems; and 11.4.2 B-link interface from ComSouth STPs. 11.4.3 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface. 11.4.4 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP. 11.4.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references. 11.4.6 BellSouth shall set message screening parameters to accept messages from ComSouth local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth switching system has a valid signaling relationship.
Appears in 2 contracts
Sources: Interconnection Agreement, Interconnection Agreement
Interface Requirements. 9.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Global Connection or ComSouthGlobal Connection-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 9.7.9.1.1 A-link interface from ComSouth Global Connection local or tandem switching systems; and
11.4.2 9.7.9.1.2 B-link interface from ComSouth Global Connection STPs.
11.4.3 9.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 9.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 9.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 9.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Global Connection local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Global Connection switching system has a valid signaling relationship.
Appears in 2 contracts
Sources: Clec Agreement, Clec Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth PLI or ComSouthSprint-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth PLI local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth PLI STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-B- links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth PLI local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth PLI switching system has a valid signaling relationship.
Appears in 2 contracts
Sources: Interconnection Agreement, Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth CCI or ComSouthCCI-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth CCI local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth CCI STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth CCI local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth CCI switching system has a valid signaling relationship.
Appears in 2 contracts
Sources: Interconnection Agreement, Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth AFN or ComSouthAFN-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth AFN local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth AFN STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth AFN local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth AFN switching system has a valid signaling relationship.
Appears in 2 contracts
Sources: Interconnection Agreement, Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Southern Telcom or ComSouthSouthern Telcom-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Southern Telcom local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Southern Telcom STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Southern Telcom local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Southern Telcom switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth NGTelecom or ComSouthNGTelecom-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth NGTelecom local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth NGTelecom STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth NGTelecom local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth NGTelecom switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Network PTS or ComSouth-Network PTS- designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Network PTS local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Network PTS STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Network PTS local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Network PTS switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth CCI or ComSouthCCI-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth CCI local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth CCI STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth CCI local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth CCI switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Starlink or ComSouthStarlink-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Starlink local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Starlink STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Starlink local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Starlink switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 6.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth INET or ComSouthINET-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 6.9.1.1 A-link interface from ComSouth INET local or tandem switching systems; and
11.4.2 6.9.1.2 B-link interface from ComSouth INET STPs.
11.4.3 6.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 6.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 6.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 6.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth INET local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth INET switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth FPB or ComSouthFPB-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth FPB local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth FPB STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth FPB local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth FPB switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 6.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Southern Telecom or ComSouthSouthern Telecom-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 6.9.1.1 A-link interface from ComSouth Southern Telecom local or tandem switching systems; and
11.4.2 6.9.1.2 B-link interface from ComSouth Southern Telecom STPs.
11.4.3 6.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 6.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 6.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 6.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Southern Telecom local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth Southern Telecom switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 6.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth ONS or ComSouthONS-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 6.9.1.1 A-link interface from ComSouth ONS local or tandem switching systems; and
11.4.2 6.9.1.2 B-link interface from ComSouth ONS STPs.
11.4.3 6.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 6.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 6.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 6.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth ONS local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ONS switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Birch or ComSouthBirch-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 7.9.1 A-link interface from ComSouth Birch local or tandem switching systems; and
11.4.2 7.9.2 B-link interface from ComSouth Birch STPs.
11.4.3 7.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 7.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 7.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 7.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Birch local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth Birch switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth ABC Telcom or ComSouthABC Telcom-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth ABC Telcom local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth ABC Telcom STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth ABC Telcom local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ABC Telcom switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth ▇▇▇▇▇▇▇▇.▇▇▇ or ComSouthAtlantic.Net-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth ▇▇▇▇▇▇▇▇.▇▇▇ local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth ▇▇▇▇▇▇▇▇.▇▇▇ STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth ▇▇▇▇▇▇▇▇.▇▇▇ local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ▇▇▇▇▇▇▇▇.▇▇▇ switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth DSL or ComSouthDSL-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 11.9.1 A-link interface from ComSouth DSL local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth DSL STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth DSL local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth DSL switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Access Point or ComSouthAccess Point-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Access Point local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Access Point STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Access Point local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Access Point switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Hotline or ComSouthHotline-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Hotline local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Hotline STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Hotline local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Hotline switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Clec Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Universal Beepers or ComSouthUniversal Beepers-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Universal Beepers local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Universal Beepers STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Universal Beepers local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Universal Beepers switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Conextel or ComSouthConextel-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Conextel local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Conextel STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Conextel local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Conextel switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth ▇▇▇▇ or ComSouth-designated ▇▇▇▇-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth ▇▇▇▇ local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth ▇▇▇▇ STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth ▇▇▇▇ local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ▇▇▇▇ switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Symtelco or ComSouthSymtelco-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Symtelco local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Symtelco STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Symtelco local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Symtelco switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth ConnectNow! or ComSouth-designated ConnectNow!-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth ConnectNow! local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth ConnectNow! STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth ConnectNow! local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ConnectNow! switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth AmTel or ComSouthAmTel-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth AmTel local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth AmTel STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth AmTel local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth AmTel switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Think 12 or ComSouthThink 12-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 11.9.1 A-link interface from ComSouth Think 12 local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Think 12 STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Think 12 local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth Think 12 switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Micro-Comm or ComSouthMicro-Comm-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Micro-Comm local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Micro-Comm STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Micro- Comm local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Micro-Comm switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Advantage Group or ComSouthAdvantage Group-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Advantage Group local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Advantage Group STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Advantage Group local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Advantage Group switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Kinetix or ComSouthKinetix-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Kinetix local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Kinetix STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Kinetix local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Kinetix switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Freedom or ComSouthFreedom-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Freedom local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Freedom STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Freedom local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Freedom switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth AmeriMex or ComSouthAmeriMex-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth AmeriMex local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth AmeriMex STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth AmeriMex local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth AmeriMex switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Utility USA or ComSouthUtility USA-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Utility USA local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Utility USA STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Utility USA local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Utility USA switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth US LEC or ComSouthUS LEC-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth US LEC local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth US LEC STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth US LEC local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth US LEC switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth ONS or ComSouthONS-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth ONS local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth ONS STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth ONS local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ONS switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Gateway or ComSouthGateway-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Gateway local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Gateway STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Gateway local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Gateway switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth SPARDI or ComSouthSPARDI-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth SPARDI local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth SPARDI STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth SPARDI local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth SPARDI switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth FLATEL or ComSouthFLATEL-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth FLATEL local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth FLATEL STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth FLATEL local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth FLATEL switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 6.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Sail Telecom or ComSouthSail Telecom-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 6.9.1.1 A-link interface from ComSouth Sail Telecom local or tandem switching systems; and
11.4.2 6.9.1.2 B-link interface from ComSouth Sail Telecom STPs.
11.4.3 6.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 6.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 6.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 6.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Sail Telecom local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Sail Telecom switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth ACN or ComSouthACN-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth ACN local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth ACN STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth ACN local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ACN switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Clec Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Seven Bridges or ComSouthSeven Bridges-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Seven Bridges local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Seven Bridges STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.AMENDMENT EXHIBIT 1 Attachment 2
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Seven Bridges local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Seven Bridges switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Preferred or ComSouthPreferred-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Preferred local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Preferred STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Preferred local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Preferred switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Grande or ComSouthGrande-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Grande local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Grande STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Grande local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Grande switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Aero or ComSouthAero-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Aero local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Aero STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Aero local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Aero switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Nexus or ComSouthNexus-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Nexus local or tandem switching systems; and
11.4.2 10.7.9.1. 2 B-link interface from ComSouth Nexus STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Nexus local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth Nexus switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Grande or ComSouthGrande-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Grande local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Grande STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Grande local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Grande switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Quality Telephone or ComSouthQuality Telephone-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Quality Telephone local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Quality Telephone STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Quality Telephone local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Quality Telephone switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 6.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth OnePoint or ComSouthOnePoint-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 6.9.1.1 A-link interface from ComSouth OnePoint local or tandem switching systems; and
11.4.2 6.9.1.2 B-link interface from ComSouth OnePoint STPs.
11.4.3 6.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 6.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 6.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 6.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth OnePoint local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth OnePoint switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 9.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Granite or ComSouthGranite-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 9.7.9.1.1 A-link interface from ComSouth Granite local or tandem switching systems; and
11.4.2 9.7.9.1.2 B-link interface from ComSouth Granite STPs.
11.4.3 9.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 9.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 9.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 9.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Granite local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Granite switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Bellsouth® / Clec Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth GSC or ComSouthGSC-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth GSC local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth GSC STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth GSC local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth GSC switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 6.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth ▇▇▇▇ or ComSouth-designated ▇▇▇▇-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 6.9.1.1 A-link interface from ComSouth ▇▇▇▇ local or tandem switching systems; and
11.4.2 6.9.1.2 B-link interface from ComSouth ▇▇▇▇ STPs.
11.4.3 6.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 6.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 6.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 6.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth ▇▇▇▇ local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ▇▇▇▇ switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Deland Actel or ComSouthDeland Actel-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth Deland Actel local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth Deland Actel STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Deland Actel local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Deland Actel switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth OnePoint or ComSouthOnePoint-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth OnePoint local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth OnePoint STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth OnePoint local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth OnePoint switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth CommuniGroup or ComSouthCommuniGroup-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth CommuniGroup local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth CommuniGroup STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth CommuniGroup local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth CommuniGroup switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth ICG or ComSouthICG-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth ICG local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth ICG STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth ICG local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ICG switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth WorldxChange or ComSouthWorldxChange-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth WorldxChange local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth WorldxChange STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOIs and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth WorldxChange local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth WorldxChange switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Clec Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Ring Connection or ComSouthRing Connection-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 11.9.1 A-link interface from ComSouth Ring Connection local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Ring Connection STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Ring Connection local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth Ring Connection switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 6.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth Freedom or ComSouthFreedom-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 6.9.1.1 A-link interface from ComSouth Freedom local or tandem switching systems; and
11.4.2 6.9.1.2 B-link interface from ComSouth Freedom STPs.
11.4.3 6.9.2 The Signaling Point of Interconnection for each link shall be located at a cross- connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 6.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 6.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 6.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth Freedom local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Freedom switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth INET or ComSouthINET-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 11.9.1 A-link interface from ComSouth INET local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth INET STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth INET local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth INET switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth ProNet or ComSouthProNet-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth ProNet local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth ProNet STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth ProNet local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth ProNet switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth US LEC or ComSouthUS LEC-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 network:
11.4.1 11.9.1 A-link interface from ComSouth US LEC local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth US LEC STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth US LEC local or tandem switching systems destined to any signaling point in the BellSouth SS7 network with which the ComSouth US LEC switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. 10.7.9.1 The following SS7 Network Interconnection interface options are available to connect ComSouth FLATEL or ComSouthFLATEL-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 10.7.9.1.1 A-link interface from ComSouth FLATEL local or tandem switching systems; and
11.4.2 10.7.9.1.2 B-link interface from ComSouth FLATEL STPs.
11.4.3 10.7.9.2 The Signaling Point of Interconnection SPOI for each link shall be located at a cross- cross-connect element in the central office CO where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points of interconnectionSPOIs. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 10.7.9.3 BellSouth shall provide intraoffice diversity between the Signaling Point of Interconnection SPOI and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 10.7.9.4 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 10.7.9.5 BellSouth shall set message screening parameters to accept messages from ComSouth FLATEL local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth FLATEL switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Spectrotel or ComSouthSpectrotel-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Spectrotel local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Spectrotel STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Spectrotel local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Spectrotel switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement
Interface Requirements. The following SS7 Network Interconnection interface options are available to connect ComSouth Excel PCHP or ComSouthExcel PCHP-designated local or tandem switching systems or signaling transfer point switches to the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network:
11.4.1 11.9.1 A-link interface from ComSouth Excel PCHP local or tandem switching systems; and
11.4.2 11.9.2 B-link interface from ComSouth Excel PCHP STPs.
11.4.3 11.9.3 The Signaling Point of Interconnection for each link shall be located at a cross- cross-connect element in the central office where the BellSouth STP is located. There shall be a DS1 or higher rate transport interface at each of the signaling points Signaling Points of interconnection. Each signaling link shall appear as a DS0 channel within the DS1 or higher rate interface.
11.4.4 11.9.4 BellSouth shall provide intraoffice diversity between the Signaling Point Points of Interconnection and the BellSouth STP, so that no single failure of intraoffice facilities or equipment shall cause the failure of both B-links in a layer connecting to a BellSouth STP.
11.4.5 11.9.5 The protocol interface requirements for SS7 Network Interconnection include the MTP, ISUPISDNUP, SCCP, and TCAP. These protocol interfaces shall conform to the applicable industry standard technical references.
11.4.6 11.9.6 BellSouth shall set message screening parameters to accept messages from ComSouth Excel PCHP local or tandem switching systems destined to any signaling point in the BellSouth SS7 ▇▇▇▇▇▇▇▇▇ ▇▇▇ network with which the ComSouth Excel PCHP switching system has a valid signaling relationship.
Appears in 1 contract
Sources: Interconnection Agreement