Measuring and Test Equipment Clause Samples

The Measuring and Test Equipment clause establishes requirements for the tools and devices used to inspect, measure, and test products or processes to ensure they meet specified standards. It typically outlines the need for equipment to be properly calibrated, maintained, and traceable to recognized standards, and may require records of calibration and maintenance to be kept. This clause ensures the accuracy and reliability of measurements, thereby reducing the risk of defects and ensuring compliance with quality or regulatory requirements.
Measuring and Test Equipment. The contractor shall use a calibration system that meets the requirements of MIL- STD-45662A, ANSI/NCSL-Z540.3-2006, or ISO 10012-1. Contractor use of a calibration system other than one specified herein will require Navy review and concurrence. (End of clause) This Section and FAR 52.204-2 “Security Requirements”, shall apply to an Order under this agreement only when DD Form 254 is attached hereto as part of the contract requirements, at which time Far 52.204-2 shall be considered Incorporated by Reference in Section I Contract Clauses of this document. The contractor shall, upon completion of final delivery hereunder, promptly so notify the Contracting Officer in writing and shall request a final military security requirements checklist (DD254). Such request shall be submitted to the Contracting Officer via the cognizant government inspector. (End of clause) When a contract is to be assigned pursuant to the FAR 52.232-23 “Assignment of Claims’ Clause Incorporated by Reference in Section I Contract Clauses of this document, the assignee shall forward a true copy of the instrument of assignment, (i.e., a certified duplicate or photostat copy of the original assignment), and an original and three (3) copies of the Notice of Assignment: A. To the Administrative Contracting Officer (ACO) located at the contract administration office specified herein, B. To the surety or sureties, if any, on any bond applicable to the contract, and C. To the Disbursing Officer designated in the contract to make payment. (End of clause) (1) of the basic clause:
View SourceView Similar (2)
Measuring and Test Equipment. Measuring and test equipments shall be controlled showing evidence of: · Equipment identification and calibration status · Proper use (range, precision, ...) · Record of proper calibration · Test records shall clearly identify any test equipment that has been used and its calibration status
View Source
Measuring and Test Equipment. If RWM Schweiz AG makes measuring and test equipment available to the supplier, then they must be labelled as RWM Schweiz AG property. The supplier is responsible for protecting this property from damage and ensuring proper calibration, maintenance and repair. The supplier must use suitable measuring and test equipment, including gauges and testing devices. The measuring equipment must be properly calibrated and the calibration traceable to a national or international standard. When utilising an external company for testing purposes or for the calibration of measuring equipment this must be accredited and verifiable. If required, suitable test equipment and testing methods shall be coordinated and agreed upon between the supplier and RWM Schweiz AG.
View Source
Measuring and Test Equipment. SUPPLIER shall be responsible for using adequate measuring and test equipment. All measuring and test equipment shall be released by way of an inspection equipment monitoring system; it must be possible to demonstrate the capability of test equipment by way of a measurement systems analysis. Test equipment monitoring and its organizational control shall as a rule be performed by means of an adequate system. Furthermore, SUPPLIER shall plan the procurement of new or modified measurement equipment and facilities in such a way that a timely delivery of contractual products that meet the agreed specifications is guaranteed. SUPPLIER shall make sure, by way of a maintenance plan, that its production facilities are in a condition that allows for the on-spec and on-time manufacture of contractual products.
View Source
Measuring and Test Equipment. The Contractor must dispose over measuring and test equipment that make it possible to measure and test the relevant quality characteristics pursuant to the state of the Art. The measuring and test equipment must be calibrated regularly or else calibrated and maintained in a ready to use condition. The ability of the measuring equipment has to be verified. If re- quired, measuring and test equipment as well as measuring and testing methods have to be coordinated between the Contractee and the Contractor.
View Source
Measuring and Test Equipment. The Supplier’s measuring and test equipment shall be maintained and calibrated in accordance with ANSI Z540-1 (formerly MIL-STD-45662) or ISO 10012-1.
View Source
Measuring and Test Equipment. Vendor/supplier shall be responsible for validating the accuracy and stability of tools, gages, and test equipment used to eonstarte that any item conforms to the requirements specified by the procurement document. Documented schedules shall be maintained to provide for periodic calibration to adequate standards. Objective evidence of calibrations shall be recorded and made available for Rainbow Mykotronx review.
View Source
Measuring and Test Equipment. The Contractor shall have a blast profile gauge, wet film comb, and a dry film thickness gauge at the shop/site at all times. The Contractor shall also have at the shop/site instrumentation to measure the psychrometric conditions and the substrate temperature.
View Source

Related to Measuring and Test Equipment

  • MEASURING EQUIPMENT 1. Seller will maintain and operate, at its own, expense and at the point of delivery of gas hereunder, a meter or meters and other necessary equipment by which the volume of gas delivered hereunder shall be measured. Such meters and equipment shall remain the property of the Seller. 2. Buyer agrees to fumish to Seller electricity for operating Seller's meters, at not cost to Seller. 3. Buyer agrees to change the charts on Seller's meters at no cost to Seller and fOlward same to Seller. 4. Buyer hereby grants to Seller suitable rights-of-way and easements necessary or incidental for the installation, maintenance, operation and removal of pipeline and other facilities together with rights of ingress thereto and egress there from at all times and hereby agrees to deliver to Seller, for the sum of one dollar ($1.00), an appropriate instrument or grant defining such rights and easements located on Buyer's plant site. 5. Buyer may install, maintain and operate such check measuring equipment, including a recording gravitometer and calorimeter as it shall desire, provided that such equipment shall be so installed so as not to interfere with the operation of Seller'S measuring equipment at or near the point of deliver. However, all ▇▇▇▇▇▇▇▇ to the Buyer shall be based on the metering of the Seller, subject only to the provisions of Paragraph 8 of this Article. 6. Each party shall have the right to be present at the time of any installing, reading, cleaning, changing, repairing, inspecting, testing, calibrating, or adjusting done in connection with the other's measuring equipment used in measuring deliveries hereunder and each party shall advise the other of any intended major maintenance operation SUfficiently in advance in order that the other party may conveniently have its representative present. 7. All Installation of measuring equipment, applying to or effecting deliveries hereunder, shall be made in such manner as to permit an accurate determination of the quantity of gas delivered and ready verification of the accuracy of measurement. Orifice meter installations, if used, shall conform to the recommendation for design and installation contained in the Gas Measurement Committee Report No.3 to the American Gas Association published April, 1955, and any modifications and amendments thereof and shall include the use of flange connections. 8. Measurement on Seller's meter or meters shall be conclusive of both parties except where the meter is defective or fails to register, or if found in error, in either of which case Seller shall repair or replace the meter and the quantity of gas delivered while the meter was out of order or failed to register shall be estimated: (a) By using the registration of any check meter if installed and accurately registering, or, in the absence of (a): (b) By correcting the error if the percentage of error by calibration, test or mathematical calculation, or, in the absence of both (a) and (b) then: (c) By estimating the quantity of delivery from deliveries during periods under similar conditions when the meter was registering accurately; and an appropriate billing adjustment shall be made in accordance with the current Rules and Regulations goveming gas systems issued by the Commission. 9. Seller will maintain its meters in good order and to this end will make periodic tests of its meters pursuant to the current Rules and Regulations governing gas systems issued by the Commission, or at such shorter intervals as seem to Seller desirable. If Buyer is dissatisfied with the accuracy at any time, it may call upon Seller to have the meter tested in accordance with all regulations relating to such tests and results of such tests as found in the current Rules and Regulations governing gas systems issued by the Comrnission. 10. Each party shall preserve all records for a period of at least two (2) years.

  • Revenue Metering The Connecting Transmission Owner’s revenue metering will be located on the generator side of the 115kV breaker at the ▇▇▇▇▇ Solar Collector Substation and will consist of: • three (3) combination current/voltage transformer (“CT/VT”) units (manufacturer and model ABB/▇▇▇▇▇▇▇ KXM-550, GE Grid Solutions KOTEF ▇▇▇.▇▇, or other equivalent specified by Connecting Transmission Owner); and • one (1) revenue meter. The ratios of the CTs and VTs will be provided by Connecting Transmission Owner upon its review of the Interconnection Customer’s design documents. (Note: Connecting Transmission Owner’s revenue metering CTs and VTs cannot be used to feed the Interconnection Customer’s check meter.) SERVICE AGREEMENT NO. 2556