REBATE REQUIREMENT CALCULATIONS AND PAYMENT Sample Clauses

REBATE REQUIREMENT CALCULATIONS AND PAYMENT. The Authority and the Company have been advised by Bond Counsel that the following provisions and procedures also apply to the proceeds of the Bonds.
View SourceView Similar (2)
REBATE REQUIREMENT CALCULATIONS AND PAYMENT. The Issuer and the Concessionaire hereby covenant to comply with the rebate requirements of Section 148(f) of the Code (the “Rebate Requirement”). The Concessionaire agrees to make, or cause to be made, any calculations necessary to comply with the Rebate Requirement. A summary of the Regulations promulgated with respect to the Rebate Requirement is included in Appendix II attached hereto. Certain exceptions to the Rebate Requirement are available. For a summary of these exceptions see Appendix III attached hereto.
View Source
REBATE REQUIREMENT CALCULATIONS AND PAYMENT. The Borrower has covenanted to comply with the rebate requirements of section 148(f) of the Code as the same apply to the Notes. As long as the Borrower complies with its agreement hereunder not to invest Note Proceeds, no rebate payment to the U.S. Treasury will be required under present laws and regulations.
View Source

Related to REBATE REQUIREMENT CALCULATIONS AND PAYMENT

  • Payment Calculation District shall pay Contractor at a rate of $ per . District shall pay Contractor as described in attached Exhibit A

  • Calculation and Payment of Additional Rent Tenant shall pay to Landlord, in the manner set forth in Section 4.4.1, below, and as Additional Rent, Tenant’s Share of Direct Expenses for each Expense Year.

  • Calculation and Payment Interest on LIBOR Loans and all other Obligations and the amount of any fees set forth in Subsection 1.4 shall be calculated on the basis of a three hundred sixty (360) day year for the actual number of days elapsed. Interest on the Base Rate Loans shall be calculated on the basis of a three hundred sixty-five or -six (365-6) day year for the actual number of days elapsed. The date of funding or conversion to a Base Rate Loan and the first day of an Interest Period with respect to a LIBOR Loan shall be included in the calculation of interest. The date of payment of any Loan and the last day of an Interest Period with respect to a LIBOR Loan shall be excluded from the calculation of interest; provided, if a Loan is repaid on the same day that it is made, one (1) day’s interest shall be charged. Interest accruing on the Base Rate Loan is payable in arrears on each of the following dates or events: (i) the last day of each calendar quarter; (ii) the prepayment of such Loan (or portion thereof); and (iii) the applicable Maturity Date or the Revolving Loan Expiration Date, as the case may be, whether by acceleration or otherwise. Interest accruing on each LIBOR Loan is payable in arrears on each of the following dates or events: (i) the last day of each applicable Interest Period; (ii) if the Interest Period is longer than three (3) months, on each three-month anniversary of the commencement date of such Interest Period; (iii) the prepayment of such Loan (or portion thereof); and (iv) the applicable Maturity Date or the Revolving Loan Expiration Date, as the case may be, whether by acceleration or otherwise.

  • Average Log Length and Payment Reduction If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine ▇▇▇▇▇▇▇▇ mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.

  • CERTIFICATION OF INDEPENDENT PRICE DETERMINATION By submission of this bid, the Bidder certifies, and in the case of a joint bid each party thereto certifies as to its own organization, that in connection with this procurement: A. The prices in this bid have been arrived at independently, without consultation, collusion, communication, or agreement for the purpose of restricting competition, as to any matter relating to such prices with any other bidder or with any competitor. B. Unless otherwise required by law, the prices which have been quoted in this bid have not been knowingly disclosed by the Bidder and will not knowingly be disclosed by the Bidder prior to opening, directly or indirectly to any other Bidder or to any competitor; and, C. No attempt has been made or shall be made by the Bidder to induce any other person or bidder to submit or not to submit a bid for the purpose of restricting competition.