Scenario and Assumption Review Session Clause Samples
Scenario and Assumption Review Session. Sabre shall lead and collaborate with Customer to validate initial international codeshare assumptions and scope.
Acceptance and Assumption Assignee hereby accepts the foregoing assignment and further hereby assumes and agrees to perform, from and after January 1, 2002, all duties, obligations and responsibilities of the property manager arising under the Agreement.
Testing and Acceptance Within […***…] after RFM’s delivery of the IC Design File to ST, ST shall manufacture and deliver a commercially reasonable quantity of evaluation Product to RFM for evaluation testing. Upon RFM’s receipt of such Products from ST, RFM shall test such Products with the applicable Evaluation Software and in the applicable Evaluation Circuit Design to determine if the IC Design for such Products conforms to the applicable Specifications. Upon completion of such testing, RFM shall provide ST with the data from such testing (“Evaluation Data”). Upon ST’s receipt of the Evaluation Data, ST shall evaluate whether the Evaluation Data indicates that the IC Design conforms to the Specifications in all material respects. ST shall accept or reject the IC Design based on the Evaluation Data and shall give RFM written notice thereof within seven (7) calendar days after RFM’s delivery of the Evaluation Data to ST. An IC Design will be deemed accepted by ST if RFM has not received notification of rejection of such IC Design from ST within seven (7) calendar days after RFM’s delivery of the applicable Evaluation Data to ST. ST’s refusal to accept the IC Design must be reasonable, must be in writing and must be accompanied by a reasonably detailed description of the manner in which the IC Design fails to comply with the Specifications in all material respects (collectively, the “Deficiencies”) so that RFM can have the opportunity to correct the Deficiencies. If ST properly rejects the IC Design, RFM shall use commercially reasonable efforts to correct any Deficiencies and redeliver a corrected IC Design File within […***…] after RFM’s receipt of the rejection notice and the foregoing provisions set forth in this Section 3.3 shall be reapplied until the IC Design is accepted; provided, however, that upon the […***…] or any subsequent rejection, either party may terminate this Agreement upon thirty (30) calendar days prior written notice to the other party, unless the IC Design is accepted during such notice period.
Inspection and Acceptance Where the Master Agreement, a Participating Addendum, or an Order does not otherwise specify a process for inspection and Acceptance, this section governs. This section is not intended to limit rights and remedies under the applicable commercial code. Contractor shall provide right of access to the Lead State, or to any other authorized agent or official of the Lead State or other Participating or Purchasing Entity, at reasonable times, in order to monitor and evaluate performance, compliance, and quality assurance requirements under this Master Agreement. Upon delivery, the Purchasing Entity shall have 30 days to inspect. Products that do not meet specifications may be rejected. Failure to reject upon receipt, however, does not relieve the contractor of liability for material (nonconformity that substantially impairs value) latent or hidden defects subsequently revealed when goods are put to use. Acceptance of such goods may be revoked in accordance with the provisions of the applicable commercial code, and the Contractor is liable for any resulting expense incurred by the Purchasing Entity related to the preparation and shipping of Product rejected and returned, or for which Acceptance is revoked. If any services do not conform to contract requirements, the Purchasing Entity may require the Contractor to perform the services again in conformity with contract requirements, at no increase in Order amount. When defects cannot be corrected by re-performance, the Purchasing Entity may require the Contractor to take necessary action to ensure that future performance conforms to contract requirements; and reduce the contract price to reflect the reduced value of services performed. The warranty period shall begin upon Acceptance. The Purchasing Entity will make every effort to notify the Contractor, within thirty (30) calendar days following delivery, of non-acceptance of a Product or completion of Service. In the event that the Contractor has not been notified within 30 calendar days from delivery of Product or completion of Service, the Product and Services will be deemed accepted on the 31st day after delivery of Product or completion of Services. This clause shall not be applicable, if acceptance testing and corresponding terms have been mutually agreed to by both parties in writing. Acceptance Testing may be explicitly set out in a Master Agreement to ensure conformance to an explicit standard of performance. Acceptance Testing means the process set forth in the Master Agreement for ascertaining that the Product meets the standard of performance prior to Acceptance by the Purchasing Entity. If Acceptance Testing is prescribed, this subsection applies to applicable Products purchased under this Master Agreement, including any additional, replacement, or substitute Product(s) and any Product(s) which are modified by or with the written approval of Contractor after Acceptance by the Purchasing Entity. The Acceptance Testing period shall be thirty (30) calendar days or other time period identified in this Master Agreement or the Participating Addendum, starting from the day after the Product is delivered or, if installed, the day after the Product is installed and Contractor certifies that the Product is ready for Acceptance Testing. If the Product does not meet the standard of performance during the initial period of Acceptance Testing, Purchasing Entity may, at its discretion, continue Acceptance Testing on a day-to-day basis until the standard of performance is met. Upon rejection, the Contractor will have fifteen (15) calendar days to cure the standard of performance issue(s). If after the cure period, the Product still has not met the standard of performance, the Purchasing Entity may, at its option: (a) declare Contractor to be in breach and terminate the Order; (b) demand replacement Product from Contractor at no additional cost to Purchasing Entity; or, (c) continue the cure period for an additional time period agreed upon by the Purchasing Entity and the Contractor. Contractor shall pay all costs related to the preparation and shipping of Product returned pursuant to the section. No Product shall be deemed Accepted and no charges shall be paid until the standard of performance is met. The warranty period shall begin upon Acceptance.
Payoffs and Assumptions The Seller shall provide to the Purchaser, or its designee, copies of all assumption and payoff statements generated by the Seller on the related Mortgage Loans from the related Cut-off Date to the related Transfer Date.
Assignment and Assumption The parties to each assignment shall execute and deliver to the Administrative Agent an Assignment and Assumption, together with a processing and recordation fee in the amount of $3,500; provided, however, that the Administrative Agent may, in its sole discretion, elect to waive such processing and recordation fee in the case of any assignment. The assignee, if it is not a Lender, shall deliver to the Administrative Agent an Administrative Questionnaire.