STEERING COMPONENTS Clause Samples

The "Steering Components" clause defines the parts and mechanisms responsible for controlling the direction and maneuverability of a vehicle or equipment. This clause typically outlines which specific components—such as the steering wheel, linkages, and associated hardware—are included under this definition and may specify standards for their maintenance, repair, or replacement. Its core practical function is to clearly identify the scope of responsibility for steering-related parts, ensuring that all parties understand which elements are covered under the agreement, thereby reducing disputes and clarifying obligations.
STEERING COMPONENTS. Steering control helm assembly, steering bracket and bushing, swivel bracket bearing, control rack and yoke assembly, power steering pump, power steering cylinder, steering wheel and coupling, steering cable, steering rams.
View SourceView Similar (2)
STEERING COMPONENTS. Steering stem shaft (when damaged by a covered steering component); upper and lower steering stem bearings and bushings; axle; steering stem; handle bar; steering stem nut and tie rod ends.
View Source
STEERING COMPONENTS. Steering control assembly, steering gate, rudder, and nozzle. (Cables are excluded.)
View Source
STEERING COMPONENTS. Inner and outer tie rod ends, drag link/steering link ends, spindle bushings.
View Source
STEERING COMPONENTS. Internally lubricated parts contained within the steering gear box or rack and pinion housing, power steering pump and pulley, pump mounting bracket, high pressure line, pressure return line, power cylinder assembly, power steering control valve, electric power steering motor, steering speed sensor, power steering cooler (FACTORY INSTALLED), steering intermediate shaft and steering gear box or rack and pinion housing if damaged by failure of an internally lubricated part.
View Source

Related to STEERING COMPONENTS

  • Components Patheon will purchase and test all Components (with the exception of Client-Supplied Components) at Patheon’s expense and as required by the Specifications.

  • OPEN SOURCE COMPONENTS The DS Offerings may include open source components. Whenever notices (such as acknowledgment, copies of licenses or attribution notice) are required by the original licensor, such notices are included in the Documentation of the DS Offerings. Moreover, some open source components may not be distributed and licensed under the terms of the Agreement but under the terms of their original licenses as set forth in the Documentation of the DS Offerings themselves. Source code for open source software components is available upon request. Except for components mentioned in the section EXCLUSIONS below, the warranty and indemnification provided by DS under the Agreement apply to all open source software components and shall be provided by DS and not by the original licensor, but only for the use of the DS Offerings that is in compliance with the terms of the Agreement, and in conjunction with the DS Offerings. The original licensors of said open source software components provide them on an “as is” basis and without any liability whatsoever to Customer.

  • Third Party Components The Products and Services may contain third party components (including open source software) subject to separate license agreements. To the limited extent a third party license expressly supersedes this ▇▇▇▇, such third party license governs Customer’s use of that third party component.

  • SHOP DRAWINGS, PRODUCT DATA AND SAMPLES 4.12.1 Shop Drawings are drawings, diagrams, schedules and other, data specially prepared for the Work by the Contractor or any Subcontractor, manufacturer, supplier or distributor to illustrate some portion of the Work. 4.12.2 Product Data are illustrations, standard schedules, performance charts, instructions, brochures, diagrams and other information furnished by the Contractor to illustrate a material, product or system for some portion of the Work. 4.12.3 Samples are physical examples which illustrate materials, equipment or workmanship and establish standards by which the Work will be judged. 4.12.4 The Contractor shall review, approve and submit, with reasonable promptness and in such sequence as to cause no delay in the Work or in the work of the State or any separate contractor, all Shop Drawings, Product Data and Samples required by the Contract Documents. 4.12.5 By approving and submitting Shop Drawings, Product Data and Samples, the Contractor represents that he / she has determined and verified all materials, field measurements, and field construction criteria related thereto, or will do so, and that he / she has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. 4.12.6 The Contractor shall not be relieved of responsibility for any deviation from the requirements of the Contract Documents by the Architect's approval of Shop Drawings, Product Data or Samples under Subparagraph 2.2.7 of these General Conditions unless the Contractor has specifically informed the Architect and the State in writing of such deviation at the time of sub- mission and the Architect and the State has given written approval to the specific deviation. The Contractor shall not be relieved from responsibility for errors or omissions in the Shop Drawings, Product Data or Samples by the Architect's approval thereof. 4.12.7 The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data or Samples, to revisions other than those requested by the Architect on previous submittals. 4.12.8 No portion of the Work requiring submission of a Shop Drawing, Product Data or Sample shall be commenced until the submittal has been approved by the Architect as provided in Subparagraph 2.2.7 of these General Conditions. All such portions of the Work shall be in accordance with approved submittals.

  • Laboratory Testing All laboratories selected by UPS Freight for analyzing Controlled Substances Testing will be HHS certified.