VERIFICATION OF THE CONFORMITY OF PRODUCTION Sample Clauses

VERIFICATION OF THE CONFORMITY OF PRODUCTION. 3.1. With regard to the materials used for the manufacture of lenses, the lamps of a series shall be recognized as complying with this Regulation if:
View SourceView Similar (8)
VERIFICATION OF THE CONFORMITY OF PRODUCTION. 3.1. With regard to the materials used for the manufacture of lenses, the lamps of a series shall be recognized as complying with this Regulation if: 3.1.1. After the test for resistance to chemical agents and the test for resistance to detergents and hydrocarbons, the outer face of the samples exhibits no cracks, chipping or deformation visible to the naked eye (see paragraphs 2.2.2., 2.3.1. and 2.3.2.); 3.1.2. After the test described in paragraph 2.6.1.1., the photometric values at the points of measurement considered in paragraph 2.6.1.2. are within the limits prescribed for conformity of production by this Regulation. 3.2. If the test results fail to satisfy the requirements, the tests shall be repeated on another sample of headlamps selected at random. Annex 5 - Appendix 1 CHRONOLOGICAL ORDER OF APPROVAL TESTS A. Tests on plastic materials (lenses or samples of material supplied pursuant to paragraph 2.2.4 of this Regulation) Samples Lenses or samples of material Lenses 1.1. Limited photometry (A.5, para. 2.1.2.) X X X 1.1. Temperature change (A.5, para. 2.1.1.) X X X 1.2. Limited photometry (A.5, para. 2.1.2.) X X X 1.2.1. Transmission measurement X X X X X X X X X 1.2.2. Diffusion measurement X X X X X X 1.3. Atmospheric agents (A.5, para. 2.2.1.) X X X 1.3.1. Transmission measurement X X X 1.4. Chemical agents (A.5, para.2.2.2.) X X X 1. Diffusion measurement X X X 1.5. Detergents (A.5, para. 2.3.1.) X X X 1.6. Hydrocarbons (A.5, para. 2.3.2.) X X X 1. Transmission measurement X X X 1.7. Deterioration (A.5, para. 2.4.1.) X X X 1.7.1. Transmission measurement X X X 2. Diffusion measurement X X X 1.8. Adherence (A.5, para. 2.5.) X B. Tests on complete lamps (supplied pursuant to paragraph 2.2.3. of this Regulation) Tests Complete headlamp Sample No. 1 2 2.1. Deterioration (para. 2.6.1.1.) 2.2. Photometry (para. 2.6.1.2.) 2.3. Adherence (para. 2.6.2.) X X X METHOD OF MEASUREMENT OF THE DIFFUSION AND TRANSMISSION OF LIGHT 1. EQUIPMENT (see figure) The beam of a collimator K with a half divergence β/2 = 17.4 x 10-4 rd is limited by a diaphragm DT with an opening of 6 mm against which the sample stand is placed. A convergent achromatic lens L2, corrected for spherical aberrations, links the diaphragm DT with the receiver R; the diameter of the lens L2 shall be such that it does not diaphragm the light diffused by the sample in a cone with a half top angle of β/2 = 14°. An annular diaphragm DD with angles α0/2 = 1° et αmax/2 = 12° is placed in an image f...
View SourceView Similar (3)
VERIFICATION OF THE CONFORMITY OF PRODUCTION. 3.1. With regard to the materials used for the manufacture of lenses, the lamps of a series shall be recognized as complying with this Regulation if: 3.1.1. After the test for resistance to chemical agents and the test for resistance to detergents and hydrocarbons, the outer face of the samples exhibits no cracks, chipping or deformation visible to the naked eye (see paras. 2.2.2., 2.3.1. and 2.3.2.); 3.1.2. After the test described in paragraph 2.6.1.1., the photometric values at the points of measurement considered in paragraph 2.6.1.2. are within the limits prescribed for conformity of production by this Regulation. 3.2. If the test results fail to satisfy the requirements, the tests shall be repeated on another sample of headlamps selected at random. ▇▇▇▇▇ ▇ - ▇▇▇▇▇▇▇▇ ▇ CHRONOLOGICAL ORDER OF APPROVAL TESTS A. Tests on plastic materials (lenses or samples of material supplied pursuant to paragraph 2.2.4. of this Regulation). Samples Lenses or samples of material Lenses 1.1. Limited photometry (A.6, para. 2.1.2.) X X X 1.1. Temperature change (A.6, para. 2.1.1.) X X X
View SourceView Similar (2)
VERIFICATION OF THE CONFORMITY OF PRODUCTION. 3.1. With regard to the materials used for the manufacture of lenses, the lamps of a series shall be recognized as complying with this Regulation if: 3.1.1. After the test for resistance to chemical agents and the test for resistance to detergents and hydrocarbons, the outer face of the samples exhibits no cracks, chipping or deformation visible to the naked eye (see paragraphs 2.2.2., 2.3.1. and 2.3.2.); 3.1.2. After the test described in paragraph 2.6.1.1., the photometric values at the points of measurement considered in paragraph 2.6.1.2. are within the limits prescribed for conformity of production by this Regulation. 3.2. If the test results fail to satisfy the requirements, the tests shall be repeated on another sample of headlamps selected at random.
View Source
VERIFICATION OF THE CONFORMITY OF PRODUCTION. 3.1. With regard to the materials used for the manufacture of lenses, the lamps of a series shall be recognized as complying with this Regulation if: E/ECE/324 Rev.2/Add.112 Regulation No. 113 page 32 Annex 6 3.1.1. After the test for resistance to chemical agents and the test for resistance to detergents and hydrocarbons, the outer face of the samples exhibits no cracks, chipping or deformation visible to the naked eye (see paras. 2.2.2., 2.3.1. and 2.3.2.); 3.1.2. After the test described in paragraph 2.6.1.1., the photometric values at the points of measurement considered in paragraph 2.6.1.2. are within the limits prescribed for conformity of production by this Regulation. 3.2. If the test results fail to satisfy the requirements, the tests shall be repeated on another sample of headlamps selected at random. E/ECE/324 Rev.2/Add.112 Regulation No. 113 page 33 Annex 6 - Appendix 1
View Source

Related to VERIFICATION OF THE CONFORMITY OF PRODUCTION

  • Inspection and Verification The Secured Parties and such persons as the Secured Parties may reasonably designate shall have the right to inspect the Collateral, all records related thereto (and to make extracts and copies from such records) and the premises upon which any of the Collateral is located, to discuss the Grantor’s affairs with the officers of the Grantor and its independent accountants and to verify under reasonable procedures the validity, amount, quality, quantity, value, condition and status of, or any other matter relating to, the Collateral, including, in the case of collateral in the possession of any third Person, by contacting any account debtor or third Person possessing such Collateral for the purpose of making such a verification. Out-of-pocket expenses in connection with any inspections by representatives of the Secured Parties shall be (a) the obligations of the Grantor with respect to any inspection after the Secured Parties’ demand payment of the Notes or (b) the obligation of the Secured Parties in any other case.

  • Conformity of production 8.1. Procedures concerning conformity of production shall comply with those set out in the 1958 Agreement, Schedule 1 (E/ECE/TRANS/505/Rev.3) and meet the following requirements: 8.2. A vehicle approved pursuant to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements of paragraph 5. above; 8.3. The Type Approval Authority which has granted approval may at any time verify the conformity of control methods applicable to each production unit. The normal frequency of such inspections shall be once every two years.

  • Inspection and Tests 3.8.1 The Procuring entity or its representative shall have the right to inspect and/or to test the goods to confirm their conformity to the Contract specifications. The Procuring entity shall notify the tenderer in writing in a timely manner, of the identity of any representatives retained for these purposes. 3.8.2 The inspections and tests may be conducted in the premises of the tenderer or its subcontractor(s), at point of delivery, and/or at the Goods’ final destination If conducted on the premises of the tenderer or its subcontractor(s), all reasonable facilities and assistance, including access to drawings and production data, shall be furnished to the inspectors at no charge to the Procuring entity. 3.8.3 Should any inspected or tested goods fail to conform to the Specifications, the Procuring entity may reject the equipment, and the tenderer shall either replace the rejected equipment or make alterations necessary to make specification requirements free of costs to the Procuring entity. 3.8.4 The Procuring entity’s right to inspect, test and where necessary, reject the goods after the Goods’ arrival shall in no way be limited or waived by reason of the equipment having previously been inspected, tested and passed by the Procuring entity or its representative prior to the equipment delivery. 3.8.5 Nothing in paragraph 3.8 shall in any way release the tenderer from any warranty or other obligations under this Contract.

  • Inspection and Testing Each Constructing Entity shall cause inspection and testing of the Interconnection Facilities that it constructs in accordance with the provisions of this section. The Construction Parties acknowledge and agree that inspection and testing of facilities may be undertaken as facilities are completed and need not await completion of all of the facilities that a Constructing Entity is building.

  • Penalties for non-conformity of production 9.1. The approval granted in respect of a vehicle type pursuant to this Regulation may be withdrawn if the requirements set forth above are not met. 9.2. If a Contracting Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith so notify the other Contracting Parties applying this Regulation, by means of a communication form conforming to the model in Annex 1 to this Regulation.