Technical Approach definition

Technical Approach means the portion of the Technical Proposal providing the
View Source
Technical Approach. The modeling and the assumptions used in the modeling to support this PA are described in detail in the accompanying Technical Support Document (TSD). In general, a worst-case modeling approach was applied following EPA guidance. In all cases EPA’s ▇▇▇▇▇▇▇▇▇▇ emission model was used to generate emission estimates and CAL3QHC (version 04244) was used for the dispersion analysis. EPA’s current guidance for modeling CO Hot-Spots (Guideline for Modeling Carbon Monoxide from Roadway Intersections, U. S. EPA, EPA-454/R- 92-005, November 1992) was also applied. The assumptions and inputs used in the model were worst-case or highly conservative, leading to higher emission estimates and less dispersion (that is, greater forecast ambient concentrations) than would be expected under real-world conditions. Consequently, if a project does not cause a modeled exceedance of the NAAQS with these worst-case or conservative inputs and assumptions, then it may be stated with high confidence that an exceedance under real-world conditions would not be expected. Finally, STATE DOT consulted with the STATE AIR AGENCY to determine appropriate values for CO background concentrations and persistence factor. These values were used to arrive at an 8- hour total CO concentration for comparison with the 8-hour CO ambient air quality standard.
View Source
Technical Approach. A description of the plan for completing the goals of a project ToC- Theory of Change: The process by which a long term goal is achieved. USAID- United States Agency for International Development W4H- WASH for Health – 5 year WASH program funded by USAID starting this year in Ghana WASH- Water Sanitation and Hygiene
View Source

Examples of Technical Approach in a sentence

  • Written technical proposals shall normally address: * Technical Approach and descriptive narrative of the contractor's understanding of the requested effort * PWS in response to a SOO * Integrated Master Plan (if applicable) * Integrated Master Schedule (if applicable) * Key Personnel Assigned * Quantities/Hours of Personnel by Labor Categories and narrative justification (if applicable) * Other Direct Costs (ODCs) (materials and supplies, travel, training, etc.

  • The Statement of Technical Approach may be no longer than nine (9) pages.

  • The Statement of Technical Approach will be evaluated in accordance with the criteria in this Section 5.3.

  • The evaluation will collectively consider the DART rate, TCR, Technical Approach to Safety, and other sources of information available to the Government as part of such collective evaluation.

  • The Contractor will provide the services described in Addendum I (Scope of Services) attached hereto and made a part of this contract in accordance with Addendum III (the Contractor’s Technical Approach).

  • The IMS, MPS, and Summary Table (Factor 1, Technical Approach) dates, activities and Performance Objectives shall correlate.

  • TxDOT will evaluate responsive QSs according to the criteria in this Part A, Section 5.3. The relative weighting or importance of the evaluation criteria within each category is described in Part A, Sections 5.3.1 through 5.3.4 and is summarized below; • Technical Qualifications and Capability (35% Weighting) • Statement of Technical Approach (10% Weighting) • Project Finance Qualifications and Capability (45% Weighting) • Safety Qualifications (10% Weighting).

  • Though these pages (Summary Table) are part of the Technical Approach they will not be counted against the number of pages allocated for the technical volume.

  • The Technical Approach to Safety narrative shall be limited to two (2) single-sided pages or one (1) double- sided page.

  • The weights (points) associated with each Mission Suitability subfactor are as follows: A Management Approach 600 B Technical Approach 300 C Small Business Utilization 100 The Mission Suitability subfactors will be evaluated using the adjectival rating, definitions, and percentile ranges at NFS 1815.305(a)(3)(A).


More Definitions of Technical Approach

Technical Approach. The modeling conducted in support of this PA is described in detail in the accompanying TSD. In general, a worst-case modeling approach was applied following EPA
View Source
Technical Approach. We understand that it is essential for equity applicants to have general business knowledge for success especially, during uncertain times such as these it's imperative to stay connected and grow. Our technical approach is to deliver quality content in a virtual environment that is easy for applicants to understand, access and learn. We do this in the following ways: Online Courses: We use a secured Learning Management System for effective training. This is method of self-paced learning allows participants to watch videos, read text, complete exercises, complete assignments and take quizzes to encourage their interaction with the material in order to increase learning and comprehension. Our courses typically take 7-10 hours to complete from start to finish.
View Source
Technical Approach means the Vendor’s proposed technical tolling solution as described in the Proposal.
View Source
Technical Approach means the portion of the Technical Proposal providing the information requested in Section 4.1 of Exhibit 2 to the ITP.
View Source

Related to Technical Approach

  • Technical Support Services means the technical support and maintenance Services provided by us according to our then-current technical support policy and procedure listed at ▇▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇ (“Technical Support Policy”) when the Services are purchased.

  • Technical safeguards means the technology and the policy and procedures for its use that 27 protect electronic PHI and control access to it.

  • Non-Microsoft Product means any third-party-branded software, data, service, website or product, unless incorporated by Microsoft in a Product.

  • Technical Specifications A specification in a document defining the characteristics of a product or a service, such as the quality levels, the environmental and climate performance levels, the design for all needs, including accessibility for people with disabilities, and the evaluation of conformity, of product performance, of the use of the product, safety or dimensions, as well as requirements applicable to the product as regards the name by which it is sold, terminology, symbols, testing and test methods, packaging, marking or labelling, instructions for use, the production processes and methods at every stage in the life cycle of the supply or service, as well as the evaluation and conformity procedures;

  • Manufacturing Process means any process for—